Browse
Submit Data
Databases
API
Help

Dataset Information

22 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Effect of frequency on fretting wear behavior of Ti/TiN multilayer film on depleted uranium.

ABSTRACT: The Ti/TiN multi-layer film was prepared on the depleted uranium (DU) substrate by cathodic arc ion plating equipment. The character of multi-layer film was studied by SEM, XRD and AES, revealed that the surface was composed of small compact particle and the cross-section had a multi-layer structure. The fretting wear performance under different frequencies was performed by a MFT-6000 machine with a ball-on-plate configuration. The wear morphology was analyzed by white light interferometer, OM and SEM with an EDX. The result shows the Ti/TiN multi-layer film could greatly improve the fretting wear performance compared to the DU substrate. The fretting wear running and damaged behavior are strongly dependent on the film and test frequency. The fretting region of DU substrate and Ti/TiN multi-layer under low test frequency is gross slip. With the increase of test frequency, the fretting region of Ti/TiN multi-layer change from gross slip to mixed fretting, then to partial slip.

SUBMITTER: Wu YP

PROVIDER: S-EPMC5383101 | biostudies-literature | 2017

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Effect of frequency on fretting wear behavior of Ti/TiN multilayer film on depleted uranium.

Wu Yan-Ping YP Li Zheng-Yang ZY Zhu Sheng-Fa SF Lu Lei L Cai Zhen-Bing ZB

PloS one 20170406 4

The Ti/TiN multi-layer film was prepared on the depleted uranium (DU) substrate by cathodic arc ion plating equipment. The character of multi-layer film was studied by SEM, XRD and AES, revealed that the surface was composed of small compact particle and the cross-section had a multi-layer structure. The fretting wear performance under different frequencies was performed by a MFT-6000 machine with a ball-on-plate configuration. The wear morphology was analyzed by white light interferometer, OM a ...[more]

PMID: 28384200

Similar Datasets

Effect of elastic grading on fretting wear.

Project description:We consider fretting wear in elastic frictional contact under influence of oscillations of small amplitude and investigate the question, how wear damage can be influenced by the introduction of material gradients. To achieve a general understanding we restrict our consideration to media with a power-law dependency of the elastic modulus on depth. In this case, a complete analytical solution can be found for the final worn shape. In the limiting case of small fretting oscillations we obtain a simple, closed-form asymptotic solution of the problem. We find that the optimum grading depends on the oscillation amplitude: for large amplitudes, the use of materials with a positive exponent decreases the wear volume whilst for very small amplitudes the use of graded materials with slightly negative exponent is beneficial. Especially interesting is the case of the Gibson-medium which may help avoiding both fretting wear and fretting fatigue.

| S-EPMC6534625 | biostudies-literature

Data on the influence of TiN on wear and corrosion behavior of Ti-6Al-4V alloy fabricated through spark plasma sintering.

Project description:Data about bulk properties of Ti-6Al-4V based composites specimen achieved by powder metallurgy route using spark plasma sintering (SPS) technique is presented, with focus on the effect of TiN particles on wear and corrosion behavior of the resultant composites. Two microsized kind of powders are combined; Ti-6Al-4V and TiN. The powder mixing and SPS processing has been enhanced and consolidated.

| S-EPMC6141763 | biostudies-literature

Fretting Corrosion Behavior of Experimental Ti-20Cr Compared to Titanium.

Project description:Experimental cast titanium alloys containing 20 mass% chromium (Ti-20Cr) show preferable mechanical properties and a good corrosion resistance. This study evaluated the fretting corrosion behavior of Ti-20Cr. Ti-20Cr (n = 4) and commercially pure titanium (CP-Ti, n = 6) disk specimens were used. The fretting corrosion test was performed by electrochemical corrosion at 0.3 V in 0.9% saline solution and mechanical damage using 10 scratching cycles with three different scratching speeds (10-40 mm/s) at 10 N. After testing, the activation peak, repassivation time and surface morphology of each specimen were analyzed. The differences between the results were tested by parametric tests (α = 0.05). The average activation peaks were significantly higher in CP-Ti than in Ti-20Cr (p < 0.01), except at 20 mm/s. In the series of scratching speeds, faster scratching speeds showed higher activation peaks. The maximum activation peaks were also higher in CP-Ti. Slight differences in the repassivation time were observed between the materials at every scratching speed; faster scratching speeds showed shorter repassivation times in both materials (p < 0.05). CP-Ti showed severe damage and significantly higher wear depth than Ti-20Cr (p < 0.05). In conclusion, adding chromium to titanium reduced surface damage and improved the fretting corrosion resistance.

| S-EPMC5459177 | biostudies-other

Effects of Plasma ZrN Metallurgy and Shot Peening Duplex Treatment on Fretting Wear and Fretting Fatigue Behavior of Ti6Al4V Alloy.

Project description:A metallurgical zirconium nitride (ZrN) layer was fabricated using glow metallurgy using nitriding with zirconiuming prior treatment of the Ti6Al4V alloy. The microstructure, composition and microhardness of the corresponding layer were studied. The influence of this treatment on fretting wear (FW) and fretting fatigue (FF) behavior of the Ti6Al4V alloy was studied. The composite layer consisted of an 8-μm-thick ZrN compound layer and a 50-μm-thick nitrogen-rich Zr-Ti solid solution layer. The surface microhardness of the composite layer is 1775 HK0.1. A gradient in cross-sectional microhardness distribution exists in the layer. The plasma ZrN metallurgical layer improves the FW resistance of the Ti6Al4V alloy, but reduces the base FF resistance. This occurs because the improvement in surface hardness results in lowering of the toughness and increasing in the notch sensitivity. Compared with shot peening treatment, plasma ZrN metallurgy and shot peening composite treatment improves the FW resistance and enhances the FF resistance of the Ti6Al4V alloy. This is attributed to the introduction of a compressive stress field. The combination of toughness, strength, FW resistance and fatigue resistance enhance the FF resistance for titanium alloy.

| S-EPMC5502668 | biostudies-other

The Wear Behavior of the Laser Cladded Ti-Al-Si Composite Coatings on Ti-6Al-4V Alloy with Additional TiC.

Project description:In this study, the Ti-Al-Si + xTiC (x = 0, 2, 6, 10 wt.%) composite coatings, each with a different content of TiC were fabricated on a Ti-6Al-4V alloy by laser surface cladding. The microstructure of the prepared coatings was analyzed by the scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). The microhardness and the wear resistance of these coatings were also evaluated. The results show that α-Ti, Ti3Al, Ti5Si3, TiAl3, TiAl, Ti3AlC2 and TiC particles can be found in the composites. The microstructure can obviously be refined by increasing the content of TiC particles, while the microhardness increases and the coefficient of friction decreases. The Ti-Al-Si-6TiC composite shows the best wear resistance, owing to its relatively fine microstructure and high content of TiC particles. The microhardness of this coating is 5.3 times that of the substrate, while the wear rate is only 0.43 times. However, when the content of TiC was up to 10 wt.%, the original TiC could not be dissolved completely during the laser cladding process, leading to formation of cracks on the coatings.

| S-EPMC8400223 | biostudies-literature

Investigation of the Optoelectronic Properties of Ti-doped Indium Tin Oxide Thin Film.

Project description:: In this study, direct-current magnetron sputtering was used to fabricate Ti-doped indium tin oxide (ITO) thin films. The sputtering power during the 350-nm-thick thin-film production process was fixed at 100 W with substrate temperatures increasing from room temperature to 500 °C. The Ti-doped ITO thin films exhibited superior thin-film resistivity (1.5 × 10-⁴ Ω/cm), carrier concentration (4.1 × 1021 cm-³), carrier mobility (10 cm²/Vs), and mean visible-light transmittance (90%) at wavelengths of 400-800 nm at a deposition temperature of 400 °C. The superior carrier concentration of the Ti-doped ITO alloys (>1021 cm-³) with a high figure of merit (81.1 × 10-³ Ω-¹) demonstrate the pronounced contribution of Ti doping, indicating their high suitability for application in optoelectronic devices.

| S-EPMC5512923 | biostudies-other

Modeling Fretting Wear Resistance and Shakedown of Metallic Materials with Graded Nanostructured Surfaces.

Project description:In applications involving fretting wear damage, surfaces with high yield strength and wear resistance are required. In this study, the mechanical responses of materials with graded nanostructured surfaces during fretting sliding are investigated and compared to homogeneous materials through a systematic computational study. A three-dimensional finite element model is developed to characterize the fretting sliding characteristics and shakedown behavior with varying degrees of contact friction and gradient layer thicknesses. Results obtained using a representative model material (i.e., 304 stainless steel) demonstrate that metallic materials with a graded nanostructured surface could exhibit a more than 80% reduction in plastically deformed surface areas and volumes, resulting in superior fretting damage resistance in comparison to homogeneous coarse-grained metals. In particular, a graded nanostructured material can exhibit elastic or plastic shakedown, depending on the contact friction coefficient. Optimal fretting resistance can be achieved for the graded nanostructured material by decreasing the friction coefficient (e.g., from 0.6 to 0.4 in 304 stainless steel), resulting in an elastic shakedown behavior, where the plastically deformed volume and area exhibit zero increment in the accumulated plastic strain during further sliding. These findings in the graded nanostructured materials using 304 stainless steel as a model system can be further tailored for engineering optimal fretting damage resistance.

| S-EPMC10222345 | biostudies-literature

The Effect of Modulation Ratio of Cu/Ni Multilayer Films on the Fretting Damage Behaviour of Ti-811 Titanium Alloy.

Project description:To improve the fretting damage (fretting wear and fretting fatigue) resistance of Ti-811 titanium alloy, three Cu/Ni multilayer films with the same modulation period thickness (200 nm) and different modulation ratios (3:1, 1:1, 1:3) were deposited on the surface of the alloy via ion-assisted magnetron sputtering deposition (IAD). The bonding strength, micro-hardness, and toughness of the films were evaluated, and the effect of the modulation ratio on the room-temperature fretting wear (FW) and fretting fatigue (FF) resistance of the alloy was determined. The results indicated that the IAD technique can be successfully used to prepare Cu/Ni multilayer films, with high bonding strength, low-friction, and good toughness, which yield improved room-temperature FF and FW resistance of the alloy. For the same modulation period (200 nm), the micro-hardness, friction, and FW resistance of the coated alloy increased, decreased, and improved, respectively, with increasing modulation ratio of the Ni-to-Cu layer thickness. However, the FF resistance of the coated alloy increased non-monotonically with the increasing modulation ratio. Among the three Cu/Ni multilayer films, those with a modulation ratio of 1:1 can confer the highest FF resistance to the Ti-811 alloy, owing mainly to their unique combination of good toughness, high strength, and low-friction.

| S-EPMC5552178 | biostudies-other

Corrosion and Wear Behavior of TiO2/TiN Duplex Coatings on Titanium by Plasma Electrolytic Oxidation and Gas Nitriding.

Project description:In this study, corrosion and wear behavior of three kinds of coatings by two processes, namely, plasma electrolytic oxidation (PEO) coatings (Ti/TiO2), gas nitriding coating (Ti/TiN), and the duplex coating (Ti/TiO2-N) by combination of PEO and gas nitriding methods were systematically investigated. X-ray diffraction tests, field-emission scanning electron microscopy, and adhesion tests are employed for the coating characterization, along with the wear and electrochemical test for evaluating the corrosion and tribological properties. The morphology and structure of the coating consist of micro-cavities known as the pancake structure on the surface. The electrolytic plasma oxidation process produces a typical annealing behavior with a low friction coefficient based on the wear test. The coating consists of nitride and nitrate/oxides titanium for nitrided samples. The surface morphology of nitrided oxide titanium coating shows a slight change in the size of the crystals and the diameter of the cavities due to the influence of nitrogen in the titanium oxide coating. The tribological behavior of the coatings showed that the wear resistance of the duplex coating (Ti/TiO2-N) and Ti/TiO2 coatings is significantly higher compared to Ti/TiN coatings and uncoated Ti samples. The polarization resistance of the Ti/TiO2-N and Ti/TiO2 coatings was 632.2 and 1451.9 kΩ cm2, respectively. These values are considerably greater than that of the uncoated Ti (135.9 kΩ cm2). Likewise, impedance showed that the Ti/TiO2-N and Ti/TiO2 coatings demonstrate higher charge transfer resistance than that of other samples due to better insulating behavior and denser structure.

| S-EPMC9741034 | biostudies-literature

Effect of the Ultrasonic Surface Rolling Process on the Fretting Fatigue Behavior of Ti-6Al-4V Alloy.

Project description:The effect of the ultrasonic surface rolling process (USRP) on the rotary bending fretting fatigue (FF) of Ti-6Al-4V alloy was investigated. The reason for the USRP's ability to improve the FF resistance of Ti-6Al-4V alloy was studied. The results revealed that the USRP induced a compressive residual stress field with a depth of 530 μm and a maximum residual stress of -930 MPa. Moreover, the surface micro-hardness of the USRP sample was significantly higher than that of the untreated base material (BM) sample, and the USRP yielded a 72.7% increase in the FF limit of the alloy. These further enhanced fatigue properties contributed mainly to the compressive residual stress field with large numerical value and deep distribution, which could effectively suppress FF crack initiation and early propagation. The USRP-induced surface work-hardening had only a minor impact on the FF resistance.

| S-EPMC5551876 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data