Dataset Information

Effects of flow rate on the migration of different plasticizers from PVC infusion medical devices.

ABSTRACT: Infusion medical devices (MDs) used in hospitals are often made of plasticized polyvinylchloride (PVC). These plasticizers may leach out into infused solutions during clinical practice, especially during risk-situations, e.g multiple infusions in Intensive Care Units and thus may enter into contact with the patients. The migrability of the plasticizers is dependent of several clinical parameters such as temperature, contact time, nature of the simulant, etc… However, no data is available about the influence of the flow rate at which drug solutions are administrated. In this study, we evaluated the impact of different flow rates on the release of the different plasticizers during an infusion procedure in order to assess if they could expose the patients to more toxic amounts of plasticizers. Migration assays with different PVC infusion sets and extension lines were performed with different flow rates that are used in clinical practice during 1h, 2h, 4h, 8h and 24h, using a lipophilic drug simulant. From a clinical point of view, the results showed that, regardless of the plasticizer, the faster the flow rate, the higher the infused volume and the higher the quantities of plasticizers released, both from infusion sets and extension lines, leading to higher patient exposure. However, physically, there was no significant difference of the migration kinetics linked to the flow rate for a same medical device, reflecting complex interactions between the PVC matrix and the simulant. The migration was especially dependent on the nature and the composition of the medical device.

SUBMITTER: Bernard L

PROVIDER: S-EPMC5825016 | biostudies-literature | 2018

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Effects of flow rate on the migration of different plasticizers from PVC infusion medical devices.

Bernard Lise L Eljezi Teuta T Clauson Hélène H Lambert Céline C Bouattour Yassine Y Chennell Philip P Pereira Bruno B Sautou Valérie V

PloS one 20180223 2

Infusion medical devices (MDs) used in hospitals are often made of plasticized polyvinylchloride (PVC). These plasticizers may leach out into infused solutions during clinical practice, especially during risk-situations, e.g multiple infusions in Intensive Care Units and thus may enter into contact with the patients. The migrability of the plasticizers is dependent of several clinical parameters such as temperature, contact time, nature of the simulant, etc… However, no data is available about t ...[more]

PMID: 29474357

Similar Datasets

Project description:BackgroundOne in five patients admitted to the hospital treated with intravenous (IV) fluid therapy suffer complications due to inappropriate administration. Errors have been reported in 13-84% of the preparation and administration of IV medications. The safe delivery of IV fluids requires precise rate administration.ObjectivesThis systematic review aims to determine the accuracy of infusion sets and devices and examine the factors that affect the flow rate accuracy of devices.Data sources and methodsSix databases (CINAHL, MEDLINE PubMed, EMBASE, Web of Science and Cochrane Database of systematic reviews) were systematically searched. Search terms included infusion pumps, infusion devices, flow rate accuracy, fluid administration rate, gravity-led infusion set and fluid balance. Studies were included if they examined infusion devices' flow rate accuracy and drop rates for fluids or non-oncological drugs. Findings were tabulated and synthesised qualitatively. The quality of the studies was examined based on the design of the studies due to their heterogeneity.ResultsEight studies were included: Four studies were conducted on human subjects in the hospital environment; studies recruited 182 participants between the ages of 18 and 94 years. Two studies examined flow rate accuracy in recruited patients across 509 observations and 2387 drip hours. No trials prospectively assessed the accuracy of infusion pumps in the clinical domain, and no studies were reported on patient safety outcomes. Four studies examined the impact of mechanical and physiological factors on the flow rate accuracies of infusion devices. Height and back pressure simulated vibrating conditions, the viscosity of IV fluid and the positions of patients were reported to have a significant impact on infusion volume and flow rates of infusion devices. Additionally, giving sets that vary from the manufacturer's specifications are reported to increase error percent by 10-20%.ConclusionInfusion devices are an important source of error in administering IV fluids. Yet, there needs to be more prospective trial data to support their clinical accuracy and the impact on patient outcomes. Future flow variability and accuracy studies should capture their impact on patient safety and clinical outcomes.

Project description:BackgroundMedical devices (MDs) in polyvinyl chloride (PVC) are not a well-known source of exposure to plasticizers, in particular during pregnancy. Because of its toxicity, the di-(2-ethylhexyl) phthalate (DEHP) has been replaced by other plasticizers such as di (isononyl)-cyclohexane-1,2-dicarboxilic acid (DINCH), tri-octyltrimellitate (TOTM) and di-(isononyl) phthalate (DiNP). Our study aimed to quantify the plasticizers (DEHP and alternative plasticizers) contained in PVC medical devices used for hospitalised pregnant women and to describe which these MDs had been used (type, number, duration of exposure).MethodsThe plasticizers contained in the MDs used for daily care in the Obstetrics Department of a French University Hospital were extracted from PVC (after contact with a chloroform solution), identified and quantified by gas-chromatography-mass-spectrometry analysis. A total of 168 pregnant women hospitalised in the Obstetrics Department with at least one catheter were included in the observational study. The median number of MDs containing plasticizers used and the daily duration of exposure to the MDs were compared in three groups of pregnant women: "Pathology group" (women hospitalised for an obstetric disorder who did not give birth during this hospitalisation; n = 52), "Pathology and delivery group" (hospitalised for an obstetric disorder and who gave birth during this stay; n = 23) and "Delivery group" (admitted for planned or spontaneous delivery without obstetric disorder; n = 93).ResultsDiNP, TOTM and DINCH were the predominant plasticizers contained in the MDs at an amount of 29 to 36 g per 100 g of PVC. Women in the "Pathology group" (preterm labour or other pathology) were exposed to a median number of two MDs containing TOTM and one MD containing DiNP, fewer than those in the "Pathology and delivery group" (p < 0.05). Women in the "Pathology group" had a median exposure of 3.4 h/day to MDs containing DiNP and 8.2 h/day to MDs containing TOTM, longer than those in the "Delivery group" (p < 0.01).ConclusionsOur study shows that the medical management of pregnant women in a hospital setting entails exposure to MDs containing alternative plasticizers (DiNP, TOTM and DINCH).

Project description:Medical tubings in plasticized polyvinylchloride (PVC) are widely used for the infusion of medications but are known in some cases to cause content-container interactions (drug sorption and plasticizer release). The aim of this study was to assess interactions between drugs and five alternative materials to a reference plasticized PVC intravenous (IV) infusion tubing: three were PVC coextruded with polyethylene (PE), polyurethane (PU) or a thermoplastic elastomer (Styrene-EthyleneButadiene-Styrene (SEBS)) and two were SEBS or thermoplastic olefin (TPO) monolayer tubings. Diazepam and insulin were chosen as respective reference of absorption and adsorption while paracetamol acted as a negative control. The concentration of each drug was quantified with liquid chromatography to evaluate a potential loss after a static contact condition and simulated infusion at 1 mL/h and 10 mL/h dynamic condition by an electric syringe pump. A characterization of each material's surface was performed by Fourier transform infrared spectroscopy in attenuated total reflection mode (ATR-FTIR) and by measurement of surface zeta potential. Plasticizer release was quantified by gas chromatography coupled with mass spectrometry (GC-MS). For all tubings except PVC/PU, no loss of paracetamol was observed in any condition. Diazepam sorption appeared to be less important with PVC/PE, PVC/SEBS, SEBS and TPO tubings than with PVC, but was more important when using PVC/PU tubings. PVC tubings induced the least loss of insulin amongst all the studied materials. Surface analysis by ATR-FTIR highlighted the presence of a plasticizer (that could be attributed to Tris (2-Ethylhexyl) Trimellitate (TOTM)) in the coextruded SEBS layer of PVC/SEBS, which could have influenced drug sorption, probably as a consequence of a migration from the PVC layer. Coextruded PVC/SEBS and PVC/PE presented the lowest zeta potential of all studied materials with respective values of -39 mV and -36 mV and were related to the highest sorption of insulin while PVC/PU with the highest zeta potential (about -9 mV) presented the highest absorption of diazepam. Coextruded layered materials appeared to have a lower plasticizer release than PVC alone. As a conclusion, PVC/PE and thermoplastic elastomers alone or coextruded with PVC could be interesting alternatives to PVC tubings with regards to sorption phenomena and plasticizer release.

Dataset Information

Effects of flow rate on the migration of different plasticizers from PVC infusion medical devices.

Publications

Effects of flow rate on the migration of different plasticizers from PVC infusion medical devices.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets