Dataset Information

Segmental Additive Tissue Engineering.

ABSTRACT: Segmental bone defects caused by trauma and disease represent a major clinical problem worldwide. Current treatment options are limited and often associated with poor outcomes and severe complications. Bone engineering is a promising alternative solution, but a number of technical challenges must be addressed to allow for effective and reproducible construction of segmental grafts that meet the size and geometrical requirements needed for individual patients and routine clinical applications. It is important to devise engineering strategies and standard operating procedures that make it possible to scale up the size of bone-engineered grafts, minimize process and product variability, and facilitate technology transfer and implementation. To address these issues, we have combined traditional and modular tissue engineering approaches in a strategy referred to as Segmental Additive Tissue Engineering (SATE). To demonstrate this approach, a digital reconstruction of a rabbit femoral defect was partitioned transversally to the longitudinal axis into segments (modules) with discoidal geometry and defined thickness to enable protocol standardization and effective tissue formation in vitro. Bone grafts corresponding to each segment were then engineered using biomimetic scaffolds seeded with human induced pluripotent stem cell-derived mesodermal progenitors (iPSC-MPs) and a novel perfusion bioreactor with universal design. The SATE strategy enables the effective and reproducible engineering of segmental bone grafts for personalized skeletal reconstruction, and will facilitate technology transfer and implementation of a tissue engineering approach to segmental bone defect therapy.

SUBMITTER: Sladkova M

PROVIDER: S-EPMC6052158 | biostudies-literature | 2018 Jul

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Segmental Additive Tissue Engineering.

Sladkova Martina M Alawadhi Rawan R Jaragh Alhaddad Rawan R Esmael Asmaa A Alansari Shoug S Saad Munerah M Mulla Yousef Jenan J Alqaoud Lulwa L de Peppo Giuseppe Maria GM

Scientific reports 20180718 1

Segmental bone defects caused by trauma and disease represent a major clinical problem worldwide. Current treatment options are limited and often associated with poor outcomes and severe complications. Bone engineering is a promising alternative solution, but a number of technical challenges must be addressed to allow for effective and reproducible construction of segmental grafts that meet the size and geometrical requirements needed for individual patients and routine clinical applications. It ...[more]

PMID: 30022102

Similar Datasets

Project description:BackgroundBone tissue engineering is not widely used in clinical treatment. Two main reasons hide behind this: (1) the seed cells are difficult to obtain and (2) the process of tissue engineering bone construction is too complex and its efficiency is still relatively low. It is foreseeable that in the near future, the problem of seed cell sources could be solved completely in tissue engineering bone repair. As for the complex process and low efficiency of tissue engineering bone construction, usually two strategies would be considered: (1) the construction strategy based on injectable bone tissue and (2) the construction strategy based on osteogenic cell sheets. However, the application of injectable bone tissue engineering (iBTE) strategy and osteogenic cell sheet strategy is limited and they could hardly be used directly in repairing defects of large segmental bone, especially load-bearing bone.MethodsIn this study, we built an osteogenic micro-tissue with simple construction but with a certain structure and composition. Based on this, we established a new iBTE repair strategy-osteogenic micro-tissue in situ repair strategy, mainly targeting at solving the problem of large segmental bone defect. The steps are as follows: (1) Build the biodegradable three-dimensional scaffold based on the size of the defect site with 3D printing rapid prototyping technology. (2) Implant the three-dimensional scaffold into the defect site. This scaffold is considered as the "steel framework" that could provide both mechanical support and space for bone tissue growth. (3) Inject the osteogenic micro-tissue (i.e., the "cell-extracellular matrix" complex), which could be considered as "concrete," into the three-dimensional scaffold, to promote the bone tissue regeneration in situ. Meanwhile, the digested cells were injected as the compared group in this experiment. After 3 months, the effect of in situ bone defect repair of osteogenic micro-tissue and digested cells was compared.ResultsIt is confirmed that osteogenic micro-tissue could achieve a higher efficiency on cell usage and has a better repair effect than the digested cells.ConclusionsOsteogenic micro-tissue repairing strategy would be a more promising clinical strategy to solve the problem of large segmental bone defect.

Project description:Thermoplastic polymer-filler composites are excellent materials for bone tissue engineering (TE) scaffolds, combining the functionality of fillers with suitable load-bearing ability, biodegradability, and additive manufacturing (AM) compatibility of the polymer. Two key determinants of their utility are their rheological behavior in the molten state, determining AM processability and their mechanical load-bearing properties. We report here the characterization of both these physical properties for four bone TE relevant composite formulations with poly(ethylene oxide terephthalate)/poly(butylene terephthalate (PEOT/PBT) as a base polymer, which is often used to fabricate TE scaffolds. The fillers used were reduced graphene oxide (rGO), hydroxyapatite (HA), gentamicin intercalated in zirconium phosphate (ZrP-GTM) and ciprofloxacin intercalated in MgAl layered double hydroxide (MgAl-CFX). The rheological assessment showed that generally the viscous behavior dominated the elastic behavior (G″ > G') for the studied composites, at empirically determined extrusion temperatures. Coupled rheological-thermal characterization of ZrP-GTM and HA composites showed that the fillers increased the solidification temperatures of the polymer melts during cooling. Both these findings have implications for the required extrusion temperatures and bonding between layers. Mechanical tests showed that the fillers generally not only made the polymer stiffer but more brittle in proportion to the filler fractions. Furthermore, the elastic moduli of scaffolds did not directly correlate with the corresponding bulk material properties, implying composite-specific AM processing effects on the mechanical properties. Finally, we show computational models to predict multimaterial scaffold elastic moduli using measured single material scaffold and bulk moduli. The reported characterizations are essential for assessing the AM processability and ultimately the suitability of the manufactured scaffolds for the envisioned bone regeneration application.

Dataset Information

Segmental Additive Tissue Engineering.

Publications

Segmental Additive Tissue Engineering.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure