First Order Reversal Curve Study of SmFe₂ Melt-Spun Ribbons.
Ontology highlight
ABSTRACT:
SUBMITTER: Grijalva-Castillo MC
PROVIDER: S-EPMC6212980 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:The influence of grain constraint on the magnetic field levels required to complete the isothermal martensitic transformation in magnetic shape memory alloys has been demonstrated for a NiCoMnSn alloy, and the magnetocaloric performance of an optimally heat treated alloy was quantified. Ni45CoxMn45-xSn10 melt spun ribbons with x = 2, 4, 5, and 6 were characterized. The x = 5 sample was determined to exhibit the lowest transformation thermal hysteresis (7 K) and transformation temperature range during transformation from paramagnetic austenite to nonmagnetic martensite, as well as a large latent heat of transformation (45 J kg-1 K-1). For this composition, it was found that increasing the grain size to thickness ratio of the ribbons from 0.2 to 1.2, through select heat treatments, resulted in a decrease in the magnetic field required to induce the martensitic transformation by about 3 T due to the corresponding reduction in the martensitic transformation temperature range. This decrease in the field requirement ultimately led to a larger magnetocaloric entropy change achieved under relatively smaller magnetic field levels. The giant inverse magnetocaloric effect of the optimized alloy was measured and showed that up to 25 J kg-1 K-1 was generated by driving the martensitic transition with magnetic fields up to 7 T.
| S-EPMC5543997 | biostudies-other
Project description:SnTe has been the focus of numerous experimental and theoretical studies over the last years owing to its high thermoelectric performances near 800 K when appropriately doped. Here, we demonstrate that melt-spinning, an ultrafast-quenching synthesis technique, followed by spark plasma sintering results in enhanced ZT values in polycrystalline SnTe. To illustrate the impact of this technique, the results are contrasted with those obtained on two polycrystalline samples prepared by direct quenching of molten SnTe and without quenching. SnTe melt-spun ribbons are characterized by a peculiar columnar microstructure that contributes to lower the lattice thermal conductivity below 700 K in pressed samples. More importantly, this technique results in a significant decrease in the hole concentration, giving rise to enhanced thermopower values above 500 K. The variation in the hole concentration is likely due to a slight loss of elemental Te during the melt-spinning process. Thanks to the decreased hole concentration, the thermoelectric performances are significantly enhanced with a peak ZT value of 0.6 at 800 K, which represents a 40% increase over the values measured for samples prepared with and without quenching. These findings indicate that melt-spinning provides a novel strategy to improve the thermoelectric properties of SnTe that could be worthwhile extending to substituted compounds.
| S-EPMC6645241 | biostudies-literature
Project description:The fabrication of nanocomposite films and fibers based on cellulose nanocrystals (P-tCNCs) and a thermoplastic polyurethane (PU) elastomer is reported. High-aspect-ratio P-tCNCs were isolated from tunicates using phosphoric acid hydrolysis, which is a process that affords nanocrystals displaying high thermal stability. Nanocomposites were produced by solvent casting (films) or melt-mixing in a twin-screw extruder and subsequent melt-spinning (fibers). The processing protocols were found to affect the orientation of both PU hard segments and the P-tCNCs within the PU matrix and therefore the mechanical properties. While the films were isotropic, both the polymer matrix and the P-tCNCs proved to be aligned along the fiber direction in the fibers, as shown using SAXS/WAXS, angle-dependent Raman spectroscopy, and birefringence analysis. Tensile tests reveal that fibers and films, at similar P-tCNC contents, display Young's moduli and strain-at-break that are within the same order of magnitude, but the stress-at-break was found to be ten-times higher for fibers, conferring them a superior toughness over films.
| S-EPMC6960881 | biostudies-literature
Project description:First-order reversal curve diagrams, or FORC diagrams, have been studied to determine if the widths of their distributions along the interaction and coercivity axes can be related to the mean-field magnetization dependent interaction field (MDIF). Arrays of nanowires with diameters ranging from 18 up to 100 nm and packing fractions varying from 0.4 to 12% have been analyzed. The mean-field MDIF has been measured using the remanence curves and used as a measuring scale on the FORC diagrams. Based on these measurements, the full width of the interaction field distribution and the full width at half maximum (FWHM) of the FORC distribution profile along the interaction field direction are shown to be proportional to the MDIF, and the relation between them is found. Moreover, by interpreting the full width of the coercive field distribution in terms of the dipolar induced shearing, a simple relation is found between the width of this distribution and the MDIF. Furthermore, we show that the width of the FORC distribution along the coercive field axis is equal to the width of the switching field distribution obtained by the derivation of the DC remanence curve. This was further verified with the switching field distribution determined using in-field magnetic force microscopy (MFM) for very low density nanowires. The results are further supported by the good agreement found between the experiments and the values calculated using the mean-field model, which provides analytical expressions for both FORC distributions.
| S-EPMC7721885 | biostudies-literature
Project description:For many antibacterial polymer fibres, especially for those with natural functional additives, the antibacterial response might not last over time. Moreover, the mechanical performance of polymeric fibres degrades significantly during the intended operation, such as usage in textile and industrial filter applications. The degradation process and overall ageing can lead to emitted volatile organic compounds (VOCs). This work focused on the usage of pine rosin as natural antibacterial chemical and analysed the weathering of melt-spun polyethylene (PE) and poly lactic acid (PLA) polyfilaments. A selected copolymer surfactant, as an additional chemical, was studied to better integrate rosin with the molecular structure of the plastics. The results reveal that a high 20 w-% of rosin content can be obtained by surfactant addition in non-oriented PE and PLA melt-spun polyfilaments. According to the VOC analysis, interestingly, the total emissions from the melt-spun PE and PLA fibres were lower for rosin-modified (10 w-%) fibres and when analysed below 60 ℃. The PE fibres of the polyfilaments were found to be clearly more durable in terms of the entire weathering study, i.e., five weeks of ultraviolet radiation, thermal ageing and standard washing. The antibacterial response against Gram-positive Staphylococcus aureus by the rosin-containing fibres was determined to be at the same level (decrease of 3-5 logs cfu/mL) as when using 1.0 w-% of commercial silver-containing antimicrobial. For the PE polyfilaments with rosin (10 w-%), full killing response (decrease of 3-5 logs cfu/mL) remained after four weeks of accelerated ageing at 60 ℃.
| S-EPMC7916070 | biostudies-literature
Project description:Poly(lactic acid) (PLA) is an attractive biomaterial due to its biocompatibility, biodegradability, and fiber-forming ability. However, the polymer is highly susceptible to both hydrolytic and thermal degradation during processing. Melt processing conditions typically involve high temperature and shear, whereas to prevent premature degradation, PLA needs to be processed under the mildest conditions that still yield the desired yarn properties. Thus, there is a need to determine the optimum processing conditions to achieve the desired properties of extruded PLA yarn. This study focuses on the effect of melt-spinning process parameters on the mechanical and physicochemical properties of the resulting PLA yarn and to derive their process-property relationships. The study compares the effect of process parameters like melt temperature, throughput through the spinneret, take-up speed at the wind-up roller, draw ratio, and drawing temperature on the yarn properties such as the yarn size (linear mass density), tenacity, elongation at break, crystallinity, and molecular weight. Depending on the combination of process parameters, the resulting PLA yarn had a yarn size ranging from 6.2 to 101.6 tex, tenacity ranging from 2.5 to 34.1 gf/tex, elongation at break ranging from 4 to 480%, and degree of crystallinity ranging from 14.6 to 62.2%. Certain combinations of processing parameters resulted in higher process-induced degradation, as evident from the reduction in molecular weight, ranging from 7.6% reduction to 20.5% reduction. Findings from this study increase our understanding on how different process parameters can be utilized to achieve the desired properties of the as-spun and drawn PLA yarn while controlling process-induced premature degradation.
| S-EPMC8223423 | biostudies-literature
Project description:The first order reversal curve (FORC) method is a magnetometry based technique used to capture nanoscale magnetic phase separation and interactions with macroscopic measurements using minor hysteresis loop analysis. This makes the FORC technique a powerful tool in the analysis of complex systems which cannot be effectively probed using localized techniques. However, recovering quantitative details about the identified phases which can be compared to traditionally measured metrics remains an enigmatic challenge. We demonstrate a technique to reconstruct phase-resolved magnetic hysteresis loops by selectively integrating the measured FORC distribution. From these minor loops, the traditional metrics-including the coercivity and saturation field, and the remanent and saturation magnetization-can be determined. In order to perform this analysis, special consideration must be paid to the accurate quantitative management of the so-called reversible features. This technique is demonstrated on three representative materials systems, high anisotropy FeCuPt thin-films, Fe nanodots, and SmCo/Fe exchange spring magnet films, and shows excellent agreement with the direct measured major loop, as well as the phase separated loops.
| S-EPMC7889904 | biostudies-literature
Project description:Amorphous microwires have attracted substantial attention in the past decade because of their useful technological applications. Their bistable magnetic response is determined by positive or negative magnetostriction, respectively. First-order reversal curves (FORC) are a powerful tool for analyzing the magnetization reversal processes of many-body ferromagnetic systems that are essential for a deeper understanding of those applications. After theoretical considerations about magnetostatic interactions among microwires, this work introduces a systematic experimental study and analysis of the FORC diagrams for magnetostrictive microwires exhibiting an individually bistable hysteresis loop, from a single microwire to sets of an increasing number of coupled microwires, the latter considered as an intermediate case to the standard many-body problem. We performed the study for sets of quasi-identical and different hysteretic microwires where we obtained the coercivity Hc and interaction Hu fields. In the cases with relevant magnetostatic interactions, FORC analysis supplies deeper information than standard hysteresis loops since the intrinsic fluctuations of the switching field generate a complex response. For sets of microwires with very different coercivity, the coercivity distributions of the individual microwires characterize the FORC diagram.
| S-EPMC10058406 | biostudies-literature
Project description:As textiles contribute considerably to overall anthropogenic pollution and resource consumption, increasing their circularity is essential. We report the melt-spinning of long-chain polyesters, materials recently shown to be fully chemically recyclable under mild conditions, as well as biodegradable. High-quality uniform fibers are enabled by the polymers' favorable combination of thermal stability, crystallization ability, melt strength, and homogeneity. The polyethylene-like crystalline structure endows these fibers with mechanical strength, which is further enhanced by its orientation upon drawing (tensile strength of up to 270 MPa). In vitro depolymerization by high concentrations of Humicola insolens cutinase underlines the accessibility of the fibers for enzymatic degradation, which can proceed from the surface and through the entire fiber within days, depending on the choice of the fiber material. Fibers and knitted fabrics withstand stress, as encountered in machine washing.
| S-EPMC11320378 | biostudies-literature
Project description:Poly(hydroxybutyrate-co-3-hexanoate) (PHBH) is a biodegradable thermoplastic polyester with the potential to be used in textile and medical applications. We have aimed at developing an upscalable melt-spinning method to produce fine biodegradable PHBH filaments without the use of an ice water bath or offline drawing techniques. We have evaluated the effect of different polymer grades (mol% 3-hydroxy hexanoate, molecular weight etc.) and production parameters on the tensile properties of melt-spun filaments. PHBH monofilaments (diameter < 130 µm) have been successfully melt-spun and online drawn from three different polymer grades. We report thermal and rheological properties of the polymer grades as well as morphological, thermal, mechanical, and structural properties of the melt-spun filaments thereof. Tensile strengths up to 291 MPa have been achieved. Differences in tensile performance have been correlated to structural differences with wide-angle X-ray diffraction and small-angle X-ray scattering. The measurements obtained have revealed that a synergetic interaction of a highly oriented non-crystalline mesophase with highly oriented α-crystals leads to increased tensile strength. Additionally, the effect of aging on the structure and tensile performance has been investigated.
| S-EPMC8747132 | biostudies-literature