Browse
Submit Data
Databases
API
Help

Dataset Information

40 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Influence of support-layer deformation on the intrinsic resistance of thin film composite membranes.

ABSTRACT: It is commonly believed that the overall permeation resistance of thin film composite (TFC) membranes is dictated by the crosslinked, ultrathin polyamide barrier layer, while the porous support merely serves as the mechanical support. Although this assumption might be the case under low transmembrane pressure, it becomes questionable under high transmembrane pressure. A highly porous support normally yields under a pressure of a few MPa, which can result in a significant level of compressive strain that may significantly increase the resistance to permeation. However, quantifying the influence of porous support deformation on the overall resistance of the TFC membrane is challenging. In particular, it is difficult to determine the deformation/strain of the membrane during active separation. In this study, we use nanoimprint lithography (NIL) to achieve precise compressive deformation in commercial TFC membranes. By adjusting the NIL conditions, membranes were compressed to strain levels up to 60%. SEM and AFM measurements showed that the compression had minimal impact on the barrier-layer surface morphology and total surface area with most of the deformation occurring in the support layer. DI water permeation measurements revealed that the water flux reduction decreases with an increase of strain level. Most significantly, the intrinsic membrane resistance showed negligible changes at strain levels lower than 30%-40%, but increased exponentially at higher strain levels, reaching 250%-500% of pristine (unstrained) membrane values. Using a resistance-in-series model, the strain dependency of the TFC membrane resistance can be described.

SUBMITTER: Aghajani M

PROVIDER: S-EPMC6459622 | biostudies-literature | 2018

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Fabrication of Thin Film Composite Membranes on Nanozeolite Modified Support Layer for Tailored Nanofiltration Performance.

Project description:Thin-film composite (TFC) structure has been widely employed in polymeric membrane fabrication to achieve superior performance for desalination and water treatment. In particular, TFC membranes with a thin active polyamide (PA) selective layer are proven to offer improved permeability without compromising salt rejection. Several modifications to TFCs have been proposed over the years to enhance their performance by altering the selective, intermediate, or support layer. This study proposes the modification of the membrane support using nanozeolites prepared by a unique ball milling technique for tailoring the nanofiltration performance. TFC membranes were fabricated by the interfacial polymerization of Piperazine (PIP) and 1,3,5-Benzenetricarbonyl trichloride (TMC) on Polysulfone (PSf) supports modified with nanozeolites. The nanozeolite concentration in the casting solution varied from 0 to 0.2%. Supports prepared with different nanozeolite concentrations resulted in varied hydrophilicity, porosity, and permeability. Results showed that optimum membrane performance was obtained for supports modified with 0.1% nanozeolites where pure water permeance of 17.1 ± 2.1 Lm-2 h-1 bar-1 was observed with a salt rejection of 11.47%, 33.84%, 94%, and 95.1% for NaCl, MgCl2, MgSO4, and Na2SO4 respectively.

| S-EPMC9610575 | biostudies-literature

Tuning the Ion-Selectivity of Thin-Film Composite Nanofiltration Membranes by Molecular Layer Deposition of Alucone.

Project description:This work addresses a key challenge of tailoring the ion selectivity of a thin-film composite nanofiltration membrane to a specific application, such as water softening, without altering the water permeability. We modified the active surface of a commercial NF270 membrane by molecular layer deposition (MLD) of ethylene glycol-Al (EG-alucone). With increasing deposition cycles, we found that the MLD precursors first infiltrated and deposited in the active layer of NF270, then inflated the active layer, and finally deposited on the surface as a distinct EG-alucone layer. The deposition process changed the morphology of the membrane active layer and decreased the overall density of its fixed negative charge by embedding the positively charged EG-alucone. Filtration experiments revealed that these modifications affected the ion separation properties of the membrane without significantly hindering the water permeability. Specifically, the permeation of Na+ increased relative to that of Mg2+, as indicated by the permselectivity of Na+ salts over Mg2+ salts. The changes in permselectivities with an increasing number of MLD cycles were rationalized using the dielectric, steric, and electrostatic ion exclusion mechanisms, which are related to the membrane material, pore size, and fixed charge, respectively. These relations open a path for the rational design of nanofiltration membranes with tailored selectivity by tuning the properties of the MLD layer. Filtration results of natural brackish groundwater using the MLD modified membranes agreed with the single salt experiments. As a result, water hardness was 26% lower for the permeate obtained using the MLD-modified membranes, which were found stable even during a 24 h filtration run. These results highlight the practical potential of this approach in enhancing water softening efficiency.

| S-EPMC7735666 | biostudies-literature

Comparison of performance and biofouling resistance of thin-film composite forward osmosis membranes with substrate/active layer modified by graphene oxide.

Project description:In this study, the influence mechanisms of graphene oxide (GO) on the membrane substrate/active layer for improving the water flux and anti-biofouling ability of thin-film composite (TFC) membranes in forward osmosis (FO) were systematically investigated. We fabricated a pristine TFC membrane, a TFC membrane in which the substrate or polyamide active layer was modified by GO (TFN-S membrane or TFN-A membrane), and a TFC membrane in which both the substrate and active layer were functionalized by GO (TFN-S + A membrane). Our results showed that the TFN-S membrane possesses a higher water flux (∼27.2%) than the TFN-A because the substrate that contained GO could improve the porous structure and porosity, while the TFN-A membrane exhibited a lower reverse salt flux and higher salt rejection than the TFN-S membrane, indicating that the surface properties played a more important role than the substrate for the salt rejection. Regarding the biofouling experiment, the TFN-A and TFN-S + A membranes facilitated a higher antifouling performance than the TFN-S and TFC membranes after 72 h of operation because of the greater hydrophilicity, lower roughness and facilitated higher bactericidal activity on the GO-modified surface. In addition, the biovolume and biofilm thickness of the TFN-A and TFN-S + A membranes were found to follow the same trend as flux decline performance. In conclusion, the substrate modified by GO could greatly improve the water flux, whereas the GO-functionalized active layer is favorable for salt rejection and biofouling mitigation. The advantage of TFN-A in biofouling mitigation suggests that the antibacterial effect of GO has a stronger influence on biofouling control than the changes of hydrophilicity and roughness.

| S-EPMC9060938 | biostudies-literature

Poly(aryl cyanurate)-Based Thin-Film Composite Nanofiltration Membranes.

Project description:The successful synthesis of poly(aryl cyanurate) nanofiltration membranes via the interfacial polymerization reaction between cyanuric chloride and 1,1,1-tris(4-hydroxyphenyl)ethane (TPE), atop a polyethersulfone ultrafiltration support, is demonstrated. The use of cyanuric chloride allows for the formation of a polymer that does not contain hydrolysis-susceptible amide bonds that inherently limit the stability of polyamide nanofiltration membranes. In order to achieve a thin defect-free cross-linked film via interfacial polymerization, a sufficient number of each monomer should react. However, the reactivities of the second and third chloride groups of the cyanuric chloride are moderate. Here, this difficulty is overcome by the high functionality and the high reactivity of TPE. The membranes demonstrate a typical nanofiltration behavior, with a molecular weight cutoff of 400 ± 83 g·mol-1 and a permeance of 1.77 ± 0.18 L·m-2 h-1 bar-1. The following retention behavior Na2SO4 (97.1%) > MgSO4 (92.8%) > NaCl (51.3%) > MgCl2 (32.1%) indicates that the membranes have a negative surface charge. The absence of amide bonds in the membranes was expected to result in superior pH stability as compared to polyamide membranes. However, it was found that under extremely acidic conditions (pH = 1), the performance showed a pronounced decline over the course of 2 months. Under extremely alkaline conditions (pH = 13), after 1 month, the performance was lost. After 2 months of exposure to moderate alkaline conditions (pH = 12), the MgSO4 retention decreased by 14% and the permeance increased by 2.5-fold. This degradation was attributed to the hydrolysis of the aryl cyanurate bond that behaves like an ester bond.

| S-EPMC8154205 | biostudies-literature

3D printed MOF-based mixed matrix thin-film composite membranes.

Project description:MOF-based mixed-matrix membranes (MMMs) have attracted considerable attention due to their tremendous separation performance and facile processability. In large-scale applications such as CO2 separation from flue gas, it is necessary to have high gas permeance, which can be achieved using thin membranes. However, there are only a handful of MOF MMMs that are fabricated in the form of thin-film composite (TFC) membranes. We propose herein the fabrication of robust thin-film composite mixed-matrix membranes (TFC MMMs) using a three dimensional (3D) printing technique with a thickness of 2-3 μm. We systematically studied the effect of casting concentration and number of electrospray cycles on membrane thickness and CO2 separation performance. Using a low concentration of polymer of intrinsic microporosity (PIM-1) or PIM-1/HKUST-1 solution (0.1 wt%) leads to TFC membranes with a thickness of less than 500 nm, but the fabricated membranes showed poor CO2/N2 selectivity, which could be attributed to microscopic defects. To avoid these microscale defects, we increased the concentration of the casting solution to 0.5 wt% resulting in TFC MMMs with a thickness of 2-3 μm which showed three times higher CO2 permeance than the neat PIM-1 membrane. These membranes represent the first examples of 3D printed TFC MMMs using the electrospray printing technique.

| S-EPMC9037021 | biostudies-literature

Covalently Modified Graphene Oxide and Polymer of Intrinsic Microporosity (PIM-1) in Mixed Matrix Thin-Film Composite Membranes.

Project description:In this study, mixed matrix membranes (MMMs) consisting of graphene oxide (GO) and functionalized graphene oxide (FGO) incorporated in a polymer of intrinsic microporosity (PIM-1) serving as a polymer matrix have been fabricated by dip-coating method, and their single gas transport properties were investigated. Successfully surface-modified GOs were characterized by Fourier transform infrared spectroscopy (FTIR), UV-Vis spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA). The effect of FGO loading on MMM morphology and performance was investigated by varying the FGO content in polymer matrix from 9 to 84 wt.%. Use of high FGO content in the polymer matrix helped to reveal difference in interaction of functionalized fillers with PIM-1 and even to discuss the change of FGO stiffness and filler alignment to the membrane surface depending on functional group nature.

| S-EPMC6232192 | biostudies-literature

Photothermal Optical Beam Steering Using Large Deformation Multi-Layer Thin Film Structures.

Project description:Photothermal actuation of microstructures remains an active area of research for microsystems that demand electrically isolated, remote, on-chip manipulation. In this study, large-deformation structures constructed from thin films traditional to microsystems were explored through both simulation and experiment as a rudimentary means to both steer and shape an incident light beam through photothermal actuation. A series of unit step infrared laser exposures were applied at increasing power levels to both uniformly symmetric and deliberately asymmetric absorptive structures with the intent of characterizing the photothermal tilt response. The results indicate that a small angle (<4° at ~74 W/cm2) mechanical tilt can be instantiated through central placement of an infrared beam, although directional control appears highly sensitive to initial beam placement. Greater responsivity (up to ~9° mechanical tilt at ~54 W/cm2) and gross directional control was demonstrated with an asymmetrical absorptive design, although this response was accompanied by a large amount (~5-10°) of mechanical tilt burn-in and drift. Rigorous device cycling remains to be explored, but the results suggest that these structures, and those similar in construction, can be further matured to achieve controllable photoactuation suitable for optical beam control or other applications.

| S-EPMC8070700 | biostudies-literature

Development of Thin-Film Composite Membranes for Nanofiltration at Extreme pH.

Project description:Water recycling is one of the most sustainable solutions to growing water scarcity challenges. However, wastewaters usually contain organic pollutants and often are at extreme pH, which complicates the treatment of these streams with conventional membranes. In this work, we report the synthesis of a robust membrane material that can withstand prolonged exposure to extreme pH (of 1 or 13 for 2 months). Polyamine thin film composite (TFC) membranes are prepared in situ by interfacial polymerization between 1,3,5-tris(bromomethyl)benzene (tBrMeB) and p-phenylenediamine (PPD). Contrary to conventional polyamide TFC membranes, enhanced pH stability is achieved by eliminating the carbonyl groups from the polymer network. The membranes showed pure water permeance and molecular weight cutoff (MWCO) of 0.28 ± 0.09 L m-2 h-2 bar-1 and 820 ± 132 g mol-1, respectively. The membrane performance is further enhanced by manipulating the monomer structures and replacing p-phenylenediamine with m-phenylenediamine, resulting in a higher permeance of 1.3 ± 0.3 L m-2 h-1 bar-1 and a lower MWCO of 566 ± 43 g mol-1. Given the ease of fabrication and excellent stability, this chemistry represents a step forward in the fabrication of robust membranes for industrial wastewater recycling.

| S-EPMC8593864 | biostudies-literature

Influence of Surface Micro-Patterning and Hydrogel Coating on Colloidal Silica Fouling of Polyamide Thin-Film Composite Membranes.

Project description:In this work, colloidal fouling by silica particles of different sizes on micro-patterned pristine and poly-(N-isopropylacylamide)-coated polyamide (PA) thin-film composite (TFC) membranes was studied. The competing impacts of surface micro-patterning vs. surface chemical modification on enhancing antifouling propensity in unstirred dead-end filtration conditions were systematically explored. Spatially selective deposition of silica microparticles (500 nm), driven by unequal flow distribution, was observed on micro-patterned membranes such that silica particles accumulated preferentially within the surface pattern's valleys, while keeping apexes regions not fouled. This interesting phenomenon may explain the substantially enhanced antifouling propensity of micro-patterned PA TFC membranes. A detailed mechanism for spatially selective deposition of silica microparticles is proposed. Furthermore, micro-imprinted surface patterns were revealed to influence deposition behavior/packing of silica nanoparticles (50 nm) resulting in very limited flux decline that was, almost, recovered under influence of triggering stirring stimulus during a continued silica filtration experiment. The current findings provide more insights into the potency of surface micro-patterning consolidated with hydrogel coating toward new fouling-resistant PA TFC membranes.

| S-EPMC6630248 | biostudies-literature

The Intrinsic Parameters of the Polyamide Nanofilm in Thin-Film Composite Reverse Osmosis (TFC-RO) Membranes: The Impact of Monomer Concentration.

Project description:The realistic resistance zone of water and salt molecules to transport across a TFC-RO membrane is the topmost polyamide nanofilm. The existence of hollow voids in the fully aromatic polyamide (PA) film gives its surface ridge-and-valley morphologies, which confuses the comprehensions of the definition of the PA thickness. The hollow voids, however, neither participate in salt-water separation nor hinder water penetrating. In this paper, the influence of intrinsic thickness (single wall thickness) of the PA layer on water permeability was studied by adjusting the concentration of reacting monomers. It confirms that the true permeation resistance of water molecules originates from the intrinsic thickness portion of the membrane. The experimental results show that the water permeability constant decreases from 3.15 ± 0.02 to 2.74 ± 0.10 L·m-2·h-1·bar-1 when the intrinsic thickness of the membrane increases by 9 nm. The defects on the film surface generate when the higher concentration of MPD is matched with the relatively low concentration of TMC. In addition, the role of MPD and TMC in the micro-structure of the PA membrane was discussed, which may provide a new way for the preparation of high permeability and high selectivity composite reverse osmosis membranes.

| S-EPMC9032585 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data