Ion beam etching redeposition for 3D multimaterial nanostructure manufacturing.
Ontology highlight
ABSTRACT:
SUBMITTER: Desbiolles BXE
PROVIDER: S-EPMC6475643 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:An ion beam etching system with etching endpoint detection (EPD) capability based on optical emission spectroscopy (OES) was conceived, built, and tested. An expansion chamber was added on the right side of the etching chamber to fix the optical detector for in-situ detecting. In this system, the optical detector was mounted on a seven-shaped bracket, which was fixed by two straight guides, thus the position of the optical detector could be adjusted arbitrarily to collect the emission spectrum generated by the sample during the etching process. The signal was transmitted by optical fiber to the computer for processing, and the etching endpoint could be detected after analyzing the data. Firstly, we used simple substances (Al, Cr, Si, and Mg) to analyze the feasibility of the system and determine the best position of the optical detector. In addition, we also tested the detection limit of the system. Finally, a complex multilayer film sample with different materials was tested, and the results showed that the system could clearly detect the characteristic emission lines of different layers and had a good real-time performance and excellent endpoint detection capabilities.
| S-EPMC8877325 | biostudies-literature
Project description:The electronic and optical properties of graphene are greatly dependent on the the number of layers. For the precise control of the graphene layers, atomic layer etching (ALE), a cyclic etching method achieved through chemical adsorption and physical desorption, can be the most powerful technique due to barely no damage and no contamination. In this study, we demonstrated the ALE process of graphene layers without noticeably damaging the graphene by using a controlled low energy oxygen (O2+/O+)-ion for chemical adsorption and a low energy Ar+-ion (11.2 eV) for physical desorption. In addition, using a trilayer graphene, mono- and bi-layer graphene could be successfully fabricated after one- and two-cycle ALE of the trilayer graphene, respectively. We believe that the ALE technique presented herein can be applicable to all layered materials such as graphene, black phosphorous and transition metal dichalcogenides which are important for next generation electronic devices.
| S-EPMC5446397 | biostudies-literature
Project description:We present a novel 3D printed multimaterial microfluidic proportional valve. The microfluidic valve is a fundamental primitive that enables the development of programmable, automated devices for controlling fluids in a precise manner. We discuss valve characterization results, as well as exploratory design variations in channel width, membrane thickness, and membrane stiffness. Compared to previous single material 3D printed valves that are stiff, these printed valves constrain fluidic deformation spatially, through combinations of stiff and flexible materials, to enable intricate geometries in an actuated, functionally graded device. Research presented marks a shift towards 3D printing multi-property programmable fluidic devices in a single step, in which integrated multimaterial valves can be used to control complex fluidic reactions for a variety of applications, including DNA assembly and analysis, continuous sampling and sensing, and soft robotics.
| S-EPMC4985141 | biostudies-literature
Project description:A novel method for fabricating diversiform suspended nanostructures is reported. The method utilizes focused-ion-beam (FIB) induced material redistribution and Rayleigh-Plateau instability, which determine the resulting shapes of formed nanostructures. By choosing target materials, their predefined patterns as well as FIB settings, we have achieved parallel nanofabrication of various kinds including nanostrings, nanobead chains and nanopore membranes with smooth surfaces due to the self-perfection effect of the material redistribution upon the minimization of system free energy. The diameters of the nanostrings and nanopores reach about 10 nm and 200 nm, respectively. The average period of the nanobead chains is 250 nm.
| S-EPMC4650821 | biostudies-other
Project description:Besides its interesting physical properties, graphene as a two-dimensional lattice of carbon atoms promises to realize devices with exceptional electronic properties, where freely suspended graphene without contact to any substrate is the ultimate, truly two-dimensional system. The practical realization of nano-devices from suspended graphene, however, relies heavily on finding a structuring method which is minimally invasive. Here, we report on the first electron beam-induced nano-etching of suspended graphene and demonstrate high-resolution etching down to ~7 nm for line-cuts into the monolayer graphene. We investigate the structural quality of the etched graphene layer using two-dimensional (2D) Raman maps and demonstrate its high electronic quality in a nano-device: A 25 nm-wide suspended graphene nanoribbon (GNR) that shows a transport gap with a corresponding energy of ~60 meV. This is an important step towards fast and reliable patterning of suspended graphene for future ballistic transport, nano-electronic and nano-mechanical devices.
| S-EPMC4293590 | biostudies-literature
Project description:3D printing, formally known as additive manufacturing, creates complex geometries via layer-by-layer addition of materials. While 3D printing has been historically perceived as the static addition of build layers, 3D printing is now considered as a dynamic assembly process. In this context, here a new 3D printing process is reported that executes full degree-of-freedom (DOF) transformation (translating, rotating, and scaling) of each individual building layer while utilizing continuous fabrication techniques. Transforming individual building layers within the sequential layered manufacturing process enables dynamic transformation of the 3D printed parts on-the-fly, eliminating the time-consuming redesign steps. Preserving the locality of the transformation to each layer further enables the discrete conformal transformation, allowing objects such as vascular scaffolds to be optimally fabricated to properly fit within specific patient anatomy obtained from the magnetic resonance imaging (MRI) measurements. Finally, exploiting the freedom to control the orientation of each individual building layer, multimaterials, multiaxis 3D printing capability are further established for integrating functional modules made of dissimilar materials in 3D printed devices. This final capability is demonstrated through 3D printing a soft pneumatic gripper via heterogenous integration of rigid base and soft actuating limbs.
| S-EPMC8245009 | biostudies-literature
Project description:Simultaneous 3D printing of disparate materials; metals, polymers and semiconductors with device quality interfaces and at high resolution remains challenging. Moreover, the precise placement of discrete and continuous domains to enable both device performance and electrical connectivity poses barriers to current high-speed 3D-printing approaches. Here, we report filaments with disparate materials arranged in elaborate microstructures, combined with an external adhesion promoter, to enable a wide range of topological outcomes and device-quality interfaces in 3D printed media. Filaments, structured towards light-detection, are printed into fully-connected 3D serpentine and spherical sensors capable of spatially resolving light at micron resolution across its entire centimeter-scale surface. 0-dimensional metallic microspheres generate light-emitting filaments that are printed into hierarchical 3D objects dotted with electroluminescent pixels at high device resolution of 55 µm not restricted by surface tension effects. Structured multimaterial filaments provides a path towards custom three-dimensional functional devices not realizable by existing approaches.
| S-EPMC6728390 | biostudies-literature
Project description:A robust power device for wearable technologies and soft electronics must feature good encapsulation, high deformability, and reliable electrical outputs. Despite substantial progress in materials and architectures for two-dimensional (2D) planar power configurations, fiber-based systems remain limited to relatively simple configurations and low performance due to challenges in processing methods. Here, we extend complex 2D triboelectric nanogenerator configurations to 3D fiber formats based on scalable thermal processing of water-resistant thermoplastic elastomers and composites. We perform mechanical analysis using finite element modeling to understand the fiber's deformation and the level of control and engineering on its mechanical behavior and thus to guide its dimensional designs for enhanced electrical performance. With microtexture patterned functional surfaces, the resulting fibers can reliably produce state-of-the-art electrical outputs from various mechanical deformations, even under harsh conditions. These mechanical and electrical attributes allow their integration with large and stretchable surfaces for electricity generation of hundreds of microamperes.
| S-EPMC9651858 | biostudies-literature
Project description:Production of objects with varied mechanical properties is challenging for current manufacturing methods. Additive manufacturing could make these multimaterial objects possible, but methods able to achieve multimaterial control along all three axes of printing are limited. Here we report a multi-wavelength method of vat photopolymerization that provides chemoselective wavelength-control over material composition utilizing multimaterial actinic spatial control (MASC) during additive manufacturing. The multicomponent photoresins include acrylate- and epoxide-based monomers with corresponding radical and cationic initiators. Under long wavelength (visible) irradiation, preferential curing of acrylate components is observed. Under short wavelength (UV) irradiation, a combination of acrylate and epoxide components are incorporated. This enables production of multimaterial parts containing stiff epoxide networks contrasted against soft hydrogels and organogels. Variation in MASC formulation drastically changes the mechanical properties of printed samples. Samples printed using different MASC formulations have spatially-controlled chemical heterogeneity, mechanical anisotropy, and spatially-controlled swelling that facilitates 4D printing.
| S-EPMC6377643 | biostudies-literature
Project description:3D printing has become commonplace for the manufacturing of objects with unusual geometries. Recent developments that enabled printing of multiple materials indicate that the technology can potentially offer a much wider design space beyond unusual shaping. Here we show that a new dimension in this design space can be exploited through the control of the orientation of anisotropic particles used as building blocks during a direct ink-writing process. Particle orientation control is demonstrated by applying low magnetic fields on deposited inks pre-loaded with magnetized stiff platelets. Multimaterial dispensers and a two-component mixing unit provide additional control over the local composition of the printed material. The five-dimensional design space covered by the proposed multimaterial magnetically assisted 3D printing platform (MM-3D printing) opens the way towards the manufacturing of functional heterogeneous materials with exquisite microstructural features thus far only accessible by biological materials grown in nature.
| S-EPMC4639895 | biostudies-literature