Focused-ion-beam induced rayleigh-plateau instability for diversiform suspended nanostructure fabrication.
Ontology highlight
ABSTRACT:
SUBMITTER: Li C
PROVIDER: S-EPMC4650821 | biostudies-other | 2015
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The Plateau-Rayleigh instability of a liquid column underlies a variety of fascinating phenomena that can be observed in everyday life. In contrast to the case of a free liquid cylinder, describing the evolution of a liquid layer on a solid fibre requires consideration of the solid-liquid interface. Here we revisit the Plateau-Rayleigh instability of a liquid coating a fibre by varying the hydrodynamic boundary condition at the fibre-liquid interface, from no slip to slip. Although the wavelength is not sensitive to the solid-liquid interface, we find that the growth rate of the undulations strongly depends on the hydrodynamic boundary condition. The experiments are in excellent agreement with a new thin-film theory incorporating slip, thus providing an original, quantitative and robust tool to measure slip lengths.
| S-EPMC4490368 | biostudies-literature
Project description:We report evidence of a displacive phase transformation from retained austenite to martensite during preparation of quenched and partitioned steel micro-pillars by using a focused ion beam (FIB) technique. The BCC phase produced by the FIB damage was identified as martensite. The invariant-plane strain surface relief associated with the martensitic transformation was observed in the retained austenite phase immediately after a FIB scan of the surface with the Ga+ ion beam. Use of a low acceleration voltage appears to lower the probability of the phase transformation, while a decrease of the acceleration voltage will result in an increase of the total milling time required to prepare a micro-pillar. This report addresses challenges related to the preparation of austenite micro-pillars by a conventional FIB technique.
| S-EPMC7047741 | biostudies-literature
Project description:In many areas of science and technology, patterned films and surfaces play a key role in engineering and development of advanced materials. Here, we introduce a new generic technique for the fabrication of polysaccharide nano-structures via focused electron beam induced conversion (FEBIC). For the proof of principle, organosoluble trimethylsilyl-cellulose (TMSC) thin films have been deposited by spin coating on SiO2 / Si and exposed to a nano-sized electron beam. It turns out that in the exposed areas an electron induced desilylation reaction takes place converting soluble TMSC to rather insoluble cellulose. After removal of the unexposed TMSC areas, structured cellulose patterns remain on the surface with FWHM line widths down to 70 nm. Systematic FEBIC parameter sweeps reveal a generally electron dose dependent behavior with three working regimes: incomplete conversion, ideal doses and over exposure. Direct (FT-IR) and indirect chemical analyses (enzymatic degradation) confirmed the cellulosic character of ideally converted areas. These investigations are complemented by a theoretical model which suggests a two-step reaction process by means of TMSC → cellulose and cellulose → non-cellulose material conversion in excellent agreement with experimental data. The extracted, individual reaction rates allowed the derivation of design rules for FEBIC parameters towards highest conversion efficiencies and highest lateral resolution.
| S-EPMC5009462 | biostudies-literature
Project description:Droplet impact on solid surfaces is essential for natural and industrial processes. Particularly, controlling the instability after droplet impact, and avoiding the satellite drops generation, have aroused great interest for its significance in inkjet printing, pesticide spraying, and hydroelectric power collection. Herein, we found that breaking the symmetry of the droplet impact dynamics using patterned-wettability surfaces can suppress the Plateau-Rayleigh instability during the droplet rebounding and improve the energy collection efficiency. Systematic experimental investigation, together with mechanical modeling and numerical simulation, revealed that the asymmetric wettability patterns can regulate the internal liquid flow and reduce the vertical velocity gradient inside the droplet, thus suppressing the instability during droplet rebounding and eliminating the satellite drops. Accordingly, the droplet energy utilization was promoted, as demonstrated by the improved hydroelectric power generation efficiency by 36.5%. These findings deepen the understanding of the wettability-induced asymmetrical droplet dynamics during the liquid-solid interactions, and facilitate related applications such as hydroelectric power generation and materials transportation.
| S-EPMC8635411 | biostudies-literature
Project description:A novel fabrication method based on the local sputtering of photoresist sidewalls during ion beam etching is presented. This method allows for the manufacture of three-dimensional multimaterial nanostructures at the wafer scale in only four process steps. Features of various shapes and profiles can be fabricated at sub-100-nm dimensions with unprecedented freedom in material choice. Complex nanostructures such as nanochannels, multimaterial nanowalls, and suspended networks were successfully fabricated using only standard microprocessing tools. This provides an alternative to traditional nanofabrication techniques, as well as new opportunities for biosensing, nanofluidics, nanophotonics, and nanoelectronics.
| S-EPMC6475643 | biostudies-literature
Project description:The functionalization of graphene remains an important challenge for numerous applications expected by this fascinating material. To keep advantageous properties of graphene after modification or functionalization of its structure, local approaches are a promising road. A novel technique is reported here that allows precise site-selective fluorination of graphene. The basic idea of this approach consists in the local radicalization of graphene by focused ion beam (FIB) irradiation and simultaneous introduction of XeF2 gas. A systematic series of experiments were carried out to outline the relation between inserted defect creation and the fluorination process. Based on a subsequent X-ray photoelectron spectroscopy (XPS) analysis, a 6-fold increase of the fluorine concentration on graphene under simultaneous irradiation was observed when compared to fluorination under normal conditions. The fluorine atoms are predominately localized at the defects as indicated from scanning tunneling microscopy (STM). The experimental findings are confirmed by density functional theory which predicts a strong increase of the binding energy of fluorine atoms when bound to the defect sites. The developed technique allows for local fluorination of graphene without using resists and has potential to be a general enabler of site-selective functionalization of graphene using a wide range of gases.
| S-EPMC4731758 | biostudies-literature
Project description:Focused ion beam (FIB) milling is an important rapid prototyping tool for micro- and nanofabrication and device and materials characterization. It allows for the manufacturing of arbitrary structures in a wide variety of materials, but establishing the process parameters for a given task is a multidimensional optimization challenge, usually addressed through time-consuming, iterative trial-and-error. Here, we show that deep learning from prior experience of manufacturing can predict the postfabrication appearance of structures manufactured by focused ion beam (FIB) milling with >96% accuracy over a range of ion beam parameters, taking account of instrument- and target-specific artifacts. With predictions taking only a few milliseconds, the methodology may be deployed in near real time to expedite optimization and improve reproducibility in FIB processing.
| S-EPMC9097578 | biostudies-literature
Project description:Solid-state nanopores (ssNPs) are extremely versatile single-molecule sensors and their potential have been established in numerous biomedical applications. However, the fabrication of ssNPs remains the main bottleneck to their widespread use. Herein, we introduce a rapid and localizable ssNPs fabrication method based on feedback-controlled optical etching. We show that a focused blue laser beam irreversibly etches silicon nitride (SiNx) membranes in solution. Furthermore, photoluminescence (PL) emitted from the SiNx is used to monitor the etching process in real-time, hence permitting rate adjustment. Transmission electron microscopy (TEM) images of the etched area reveal an inverted Gaussian thickness profile, corresponding to the intensity point spread function of the laser beam. Continued laser exposure leads to the opening of a nanopore, which can be controlled to reproducibly fabricate nanopores of different sizes. The optically-formed ssNPs exhibit electrical noise on par with TEM-drilled pores, and translocate DNA and proteins readily. Notably, due to the localized thinning, the laser-drilled ssNPs exhibit highly suppressed background PL and improved spatial resolution. Given the total control over the nanopore position, this easily implemented method is ideally suited for electro-optical sensing and opens up the possibility of fabricating large nanopore arrays in situ.
| S-EPMC6021433 | biostudies-literature
Project description:The Rayleigh-Plateau instability, a phenomenon of paramount significance in fluid dynamics, finds widespread application in the Continuous InkJet (CIJ) printing process. This study presents a comprehensive dataset comprising experimental investigations of fluid jet breakup phenomena under large-amplitude stimulation conditions using an industrial CIJ print-head from Markem-Imaje. Unlike previous studies, this dataset encompasses a diverse range of experimental conditions, including nine different Newtonian fluids with meticulously measured rheological properties (viscosities, surface tensions and densities). The applied stimulation amplitudes vary from 5V to 45V, representing a substantial span of excitation levels. The experimental setup captures the intricate dynamics of fluid jets subjected to these varying conditions, producing a rich collection of over 5,000 high-resolution images depicting the breakup phenomena. Each amplitude of stimulation and fluid type yields more than 55 distinct images, providing detailed insights into the evolving jet morphologies. To ensure the accuracy and relevance of the dataset, all ejection parameters are rigorously documented and included. The dataset thus serves as a valuable resource for researchers seeking to explore the dynamics of large-amplitude Rayleigh-Plateau instability in CIJ printing. Its comprehensiveness and diversity make it particularly suitable for the application of novel machine learning and deep-learning approaches, enabling the study of jet morphological evolution beyond the confines of classical Rayleigh's theory. This dataset holds promise for advancing our understanding of fluid jet dynamics and enhancing the efficiency and quality of CIJ printing processes.
| S-EPMC10801292 | biostudies-literature
Project description:This paper studies the Rayleigh-Plateau instability for co-flowing immiscible aqueous polymer solutions in a microfluidic channel. Careful vibration-free experiments with controlled actuation of the flow allowed direct measurement of the growth rate of this instability. Experiments for the well-known aqueous two phase system (ATPS, or aqueous biphasic systems) of dextran and polyethylene glycol solutions exhibited a growth rate of 1 s(-1), which was more than an order of magnitude slower than an analogous experiment with two immiscible Newtonian fluids with viscosities and interfacial tension that closely matched the ATPS experiment. Viscoelastic effects and adhesion to the walls were ruled out as explanations for the observed behavior. The results are remarkable because all current theory suggests that such dilute polymer solutions should break up faster, not slower, than the analogous Newtonian case. Microfluidic uses of aqueous two phase systems include separation of labile biomolecules but have hitherto be limited because of the difficulty in making droplets. The results of this work teach how to design devices for biological microfluidic ATPS platforms.
| S-EPMC3331863 | biostudies-other