Browse
Submit Data
Databases
API
Help

Dataset Information

21 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Time-resolved photoluminescence on double graded Cu(In,Ga)Se₂ - Impact of front surface recombination and its temperature dependence.

ABSTRACT: Time-resolved photoluminescence (TRPL) is applied to determine an effective lifetime of minority charge carriers in semiconductors. Such effective lifetimes include recombination channels in the bulk as well as at the surfaces and interfaces of the device. In the case of Cu(In,Ga)Se₂ absorbers used for solar cell applications, trapping of minority carriers has also been reported to impact the effective minority carrier lifetime. Trapping can be indicated by an increased temperature dependence of the experimentally determined photoluminescence decay time when compared to the temperature dependence of Shockley-Read-Hall (SRH) recombination alone and can lead to an overestimation of the minority carrier lifetime. Here, it is shown by technology computer-aided design (TCAD) simulations and by experiment that the intentional double-graded bandgap profile of high efficiency Cu(In,Ga)Se₂ absorbers causes a temperature dependence of the PL decay time similar to trapping in case of a recombinative front surface. It is demonstrated that a passivated front surface results in a temperature dependence of the decay time that can be explained without minority carrier trapping and thus enables the assessment of the absorber quality by means of the minority carrier lifetime. Comparison with the absolute PL yield and the quasi-Fermi-level splitting (QFLS) corroborate the conclusion that the measured decay time corresponds to the bulk minority carrier lifetime of 250 ns for the double-graded CIGS absorber under investigation.

SUBMITTER: Weiss TP

PROVIDER: S-EPMC6484473 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Emission-wavelength-dependent photoluminescence decay lifetime of N-functionalized graphene quantum dot downconverters: Impact on conversion efficiency of Cu(In, Ga)Se2 solar cells.

Project description:Graphene quantum dots (GQDs) have several advantages over inorganic quantum dots owing to their beneficial properties. Recently, GQDs have been used as downconverters in photovoltaic devices. However, the application of GQDs in most emergent thin-film-based Cu(In, Ga)Se2 (CIGS) photovoltaic cells is limited because of either low photoluminescence (PL) quantum yield (QY) or a small Stokes shift (Δλ). Therefore, GQDs with an ultrahigh QY and large Δλ are essential to realizing the two emergent fields, i.e., the application of GQDs in CIGS photovoltaic solar cells. In this regard, we synthesized nitrogen-functionalized GQDs (NGQDs) with an ultrahigh QY (77-99%) and a large Δλ (95-155 nm) via tailoring of the nitrogen and oxygen moieties. The NGQDs were applied in CIGS solar cells to evaluate their downconversion efficiency. Our study shows that the emission wavelength (λem)-dependent photoluminescence decay lifetime (τem) determines the down-conversion efficiency of the nitrogen-functionalized graphene quantum dots. With the increase in τem at λem > 500 nm, the conversion efficiencies of the NGQDs coated-CIGS solar cells increased by 12.22%. Thus, the increase in τem at λem > 500 nm significantly increased the maximum current output and thus enhanced the solar-cell performance.

| S-EPMC6658560 | biostudies-literature

Refractive indices of layers and optical simulations of Cu(In,Ga)Se2 solar cells.

Project description:Cu(In,Ga)Se2 based solar cells have reached efficiencies close to 23%. Further knowledge-driven improvements require accurate determination of the material properties. Here, we present refractive indices for all layers in Cu(In,Ga)Se2 solar cells with high efficiency. The optical bandgap of Cu(In,Ga)Se2 does not depend on the Cu content in the explored composition range, while the absorption coefficient value is primarily determined by the Cu content. An expression for the absorption spectrum is proposed, with Ga and Cu compositions as parameters. This set of parameters allows accurate device simulations to understand remaining absorption and carrier collection losses and develop strategies to improve performances.

| S-EPMC5954485 | biostudies-literature

Deliberate and Accidental Gas-Phase Alkali Doping of Chalcogenide Semiconductors: Cu(In,Ga)Se2.

Project description:Alkali metal doping is essential to achieve highly efficient energy conversion in Cu(In,Ga)Se2 (CIGSe) solar cells. Doping is normally achieved through solid state reactions, but recent observations of gas-phase alkali transport in the kesterite sulfide (Cu2ZnSnS4) system (re)open the way to a novel gas-phase doping strategy. However, the current understanding of gas-phase alkali transport is very limited. This work (i) shows that CIGSe device efficiency can be improved from 2% to 8% by gas-phase sodium incorporation alone, (ii) identifies the most likely routes for gas-phase alkali transport based on mass spectrometric studies, (iii) provides thermochemical computations to rationalize the observations and (iv) critically discusses the subject literature with the aim to better understand the chemical basis of the phenomenon. These results suggest that accidental alkali metal doping occurs all the time, that a controlled vapor pressure of alkali metal could be applied during growth to dope the semiconductor, and that it may have to be accounted for during the currently used solid state doping routes. It is concluded that alkali gas-phase transport occurs through a plurality of routes and cannot be attributed to one single source.

| S-EPMC5324121 | biostudies-literature

Optical bleaching front in bedrock revealed by spatially-resolved infrared photoluminescence.

Project description:Optically stimulated luminescence (OSL) dating of sediment, based on the accumulation of trapped charge in natural crystals since their last exposure to daylight, has revolutionised our understanding of the late Quaternary period. Recently, a complementary technique called luminescence rock surface dating (RSD), which uses differential spatial eviction of trapped charges in rocks exposed to daylight, has been developed to derive exposure and burial ages, and hard-rock erosion rates. In its current form, the RSD technique suffers from labour intensive sample preparation, uncertainties in the depth and dose rate estimates, and poor resolution of the luminescence-depth profile. Here, we develop a novel, 2D luminescence imaging technique for RSD of large rock slabs (3?×?5?cm) to overcome these challenges. We utilize the recently discovered infrared photoluminescence (IRPL) signal for direct, non-destructive imaging of the luminescence-depth profile in a sub-aerially exposed granitic rock, with an unprecedented spatial resolution of ~140?µm. We further establish a correlation between luminescence and geochemistry using micro X-ray fluorescence (µXRF) spectroscopy. Our study promises a substantial advancement in luminescence imaging and paves the path towards novel applications using 2D dating, micro-dosimetry in mixed composition samples, and portable instrumentation for in-situ luminescence measurements.

| S-EPMC6385230 | biostudies-literature

Microscopic origins of performance losses in highly efficient Cu(In,Ga)Se2 thin-film solar cells.

Project description:Thin-film solar cells based on polycrystalline absorbers have reached very high conversion efficiencies of up to 23-25%. In order to elucidate the limiting factors that need to be overcome for even higher efficiency levels, it is essential to investigate microscopic origins of loss mechanisms in these devices. In the present work, a high efficiency (21% without anti-reflection coating) copper indium gallium diselenide (CIGSe) solar cell is characterized by means of a correlative microscopy approach and corroborated by means of photoluminescence spectroscopy. The values obtained by the experimental characterization are used as input parameters for two-dimensional device simulations, for which a real microstructure was used. It can be shown that electrostatic potential and lifetime fluctuations exhibit no substantial impact on the device performance. In contrast, nonradiative recombination at random grain boundaries can be identified as a significant loss mechanism for CIGSe solar cells, even for devices at a very high performance level.

| S-EPMC7442832 | biostudies-literature

Surface/Interface Effects by Alkali Postdeposition Treatments of (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells.

Project description:Ag alloying and the introduction of alkali elements through a postdeposition treatment are two approaches to improve the performance of Cu(In,Ga)Se2 (CIGS) thin film solar cells. In particular, a postdeposition treatment of an alkali metal fluoride of the absorber has shown a beneficial effect on the solar cells performance due to an increase in the open circuit voltage (V OC) for both (Ag,Cu)(In,Ga)Se2 (ACIGS) and CIGS based solar cells. Several reasons have been suggested for the improved V OC in CIGS solar cells including absorber surface and interface effects. Less works investigated how the applied postdeposition treatment influences the ACIGS absorber surface and interface properties and the subsequent buffer layer growth. In this work we employed hard X-ray photoelectron spectroscopy to study the chemical and electronic properties at the real functional interface between a CdS buffer and ACIGS absorbers that have been exposed to different alkali metal fluoride treatments during preparation. All samples show an enhanced Ag content at the CdS/ACIGS interface as compared to ACIGS bulk-like composition, and it is also shown that this enhanced Ag content anticorrelates with Ga content. The results indicate that the absorber composition at the near-surface region changes depending on the applied alkali postdeposition treatment. The Cu and Ga decrease and the Ag increase are stronger for the RbF treatment as compared to the CsF treatment, which correlates with the observed device characteristics. This suggests that a selective alkali postdeposition treatment could change the ACIGS absorber surface composition, which can influence the solar cell behavior.

| S-EPMC8790805 | biostudies-literature

Alkali Dispersion in (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells-Insight from Theory and Experiment.

Project description:Silver alloying of Cu(In,Ga)Se2 absorbers for thin film photovoltaics offers improvements in open-circuit voltage, especially when combined with optimal alkali-treatments and certain Ga concentrations. The relationship between alkali distribution in the absorber and Ag alloying is investigated here, combining experimental and theoretical studies. Atom probe tomography analysis is implemented to quantify the local composition in grain interiors and at grain boundaries. The Na concentration in the bulk increases up to ∼60 ppm for [Ag]/([Ag] + [Cu]) = 0.2 compared to ∼20 ppm for films without Ag and up to ∼200 ppm for [Ag]/([Ag] + [Cu]) = 1.0. First-principles calculations were employed to evaluate the formation energies of alkali-on-group-I defects (where group-I refers to Ag and Cu) in (Ag,Cu)(In,Ga)Se2 as a function of the Ag and Ga contents. The computational results demonstrate strong agreement with the nanoscale analysis results, revealing a clear trend of increased alkali bulk solubility with the Ag concentration. The present study, therefore, provides a more nuanced understanding of the role of Ag in the enhanced performance of the respective photovoltaic devices.

| S-EPMC7898268 | biostudies-literature

Dataset demonstrating the modeling of a high performance Cu(In,Ga)Se2 absorber based thin film photovoltaic cell.

Project description:The physical data of the semiconductor materials used in the design of a CIGS absorber based thin film photovoltaic cell have been presented in this data article. Besides, the values of the contact parameter and operating conditions of the cell have been reported. Furthermore, by conducting the simulation with data corresponding to the device structure: soda-lime glass (SLG) substrate/Mo back-contact/CIGS absorber/CdS buffer/intrinsic ZnO/Al-doped ZnO window/Al-grid front-contact, the solar cell performance parameters such as open circuit voltage [Formula: see text], short circuit current density [Formula: see text], fill factor [Formula: see text], efficiency [Formula: see text], and collection efficiency [Formula: see text] have been analyzed.

| S-EPMC5328687 | biostudies-literature

Effect of the KF post-deposition treatment on grain boundary properties in Cu(In, Ga)Se2 thin films.

Project description:Significant power conversion efficiency improvements have recently been achieved for thin-film solar cells based on a variety of polycrystalline absorbers, including perovskites, CdTe, and Cu(In,Ga)Se2 (CIGS). The passivation of grain boundaries (GBs) through (post-deposition) treatments is a crucial step for this success. For the case of CIGS, the introduction of a potassium fluoride post-deposition treatment (KF-PDT) has boosted their power conversion efficiency to the best performance of all polycrystalline solar cells. Direct and indirect effects of potassium at the interface and interface-near region in the CIGS layer are thought to be responsible for this improvement. Here, we show that also the electronic properties of the GBs are beneficially modified by the KF-PDT. We used Kelvin probe force microscopy to study the effect of the KF-PDT on the CIGS surface by spatially resolved imaging of the surface potential. We find a clear difference for the GB electronic properties: the KF-PDT increases the band bending at GBs by about 70% and results in a narrower distribution of work function values at the GBs. This effect of the KF-PDT on the GB electronic properties is expected to contribute to the improved efficiency values observed for CIGS thin-film solar cells with KF-PDT.

| S-EPMC5269666 | biostudies-literature

Direct evidence for grain boundary passivation in Cu(In,Ga)Se2 solar cells through alkali-fluoride post-deposition treatments.

Project description:The properties and performance of polycrystalline materials depend critically on the properties of their grain boundaries. Polycrystalline photovoltaic materials - e.g. hybrid halide perovskites, copper indium gallium diselenide (CIGSe) and cadmium telluride - have already demonstrated high efficiencies and promise cost-effective electricity supply. For CIGSe-based solar cells, an efficiency above 23% has recently been achieved using an alkali-fluoride post-deposition treatment; however, its full impact and functional principle are not yet fully understood. Here, we show direct evidence for the passivation of grain boundaries in CIGSe treated with three different alkali-fluorides through a detailed study of the nanoscale optoelectronic properties. We determine a correlation of the surface potential change at grain boundaries with the open-circuit voltage, which is supported by numerical simulations. Our results suggest that heavier alkali elements might lead to better passivation by reducing the density of charged defects and increasing the formation of secondary phases at grain boundaries.

| S-EPMC6726603 | biostudies-literature