Browse
Submit Data
Databases
API
Help

Dataset Information

22 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Microscopic origins of performance losses in highly efficient Cu(In,Ga)Se₂ thin-film solar cells.

ABSTRACT: Thin-film solar cells based on polycrystalline absorbers have reached very high conversion efficiencies of up to 23-25%. In order to elucidate the limiting factors that need to be overcome for even higher efficiency levels, it is essential to investigate microscopic origins of loss mechanisms in these devices. In the present work, a high efficiency (21% without anti-reflection coating) copper indium gallium diselenide (CIGSe) solar cell is characterized by means of a correlative microscopy approach and corroborated by means of photoluminescence spectroscopy. The values obtained by the experimental characterization are used as input parameters for two-dimensional device simulations, for which a real microstructure was used. It can be shown that electrostatic potential and lifetime fluctuations exhibit no substantial impact on the device performance. In contrast, nonradiative recombination at random grain boundaries can be identified as a significant loss mechanism for CIGSe solar cells, even for devices at a very high performance level.

SUBMITTER: Krause M

PROVIDER: S-EPMC7442832 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Surface/Interface Effects by Alkali Postdeposition Treatments of (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells.

Project description:Ag alloying and the introduction of alkali elements through a postdeposition treatment are two approaches to improve the performance of Cu(In,Ga)Se2 (CIGS) thin film solar cells. In particular, a postdeposition treatment of an alkali metal fluoride of the absorber has shown a beneficial effect on the solar cells performance due to an increase in the open circuit voltage (V OC) for both (Ag,Cu)(In,Ga)Se2 (ACIGS) and CIGS based solar cells. Several reasons have been suggested for the improved V OC in CIGS solar cells including absorber surface and interface effects. Less works investigated how the applied postdeposition treatment influences the ACIGS absorber surface and interface properties and the subsequent buffer layer growth. In this work we employed hard X-ray photoelectron spectroscopy to study the chemical and electronic properties at the real functional interface between a CdS buffer and ACIGS absorbers that have been exposed to different alkali metal fluoride treatments during preparation. All samples show an enhanced Ag content at the CdS/ACIGS interface as compared to ACIGS bulk-like composition, and it is also shown that this enhanced Ag content anticorrelates with Ga content. The results indicate that the absorber composition at the near-surface region changes depending on the applied alkali postdeposition treatment. The Cu and Ga decrease and the Ag increase are stronger for the RbF treatment as compared to the CsF treatment, which correlates with the observed device characteristics. This suggests that a selective alkali postdeposition treatment could change the ACIGS absorber surface composition, which can influence the solar cell behavior.

| S-EPMC8790805 | biostudies-literature

Alkali Dispersion in (Ag,Cu)(In,Ga)Se2 Thin Film Solar Cells-Insight from Theory and Experiment.

Project description:Silver alloying of Cu(In,Ga)Se2 absorbers for thin film photovoltaics offers improvements in open-circuit voltage, especially when combined with optimal alkali-treatments and certain Ga concentrations. The relationship between alkali distribution in the absorber and Ag alloying is investigated here, combining experimental and theoretical studies. Atom probe tomography analysis is implemented to quantify the local composition in grain interiors and at grain boundaries. The Na concentration in the bulk increases up to ∼60 ppm for [Ag]/([Ag] + [Cu]) = 0.2 compared to ∼20 ppm for films without Ag and up to ∼200 ppm for [Ag]/([Ag] + [Cu]) = 1.0. First-principles calculations were employed to evaluate the formation energies of alkali-on-group-I defects (where group-I refers to Ag and Cu) in (Ag,Cu)(In,Ga)Se2 as a function of the Ag and Ga contents. The computational results demonstrate strong agreement with the nanoscale analysis results, revealing a clear trend of increased alkali bulk solubility with the Ag concentration. The present study, therefore, provides a more nuanced understanding of the role of Ag in the enhanced performance of the respective photovoltaic devices.

| S-EPMC7898268 | biostudies-literature

Dataset demonstrating the modeling of a high performance Cu(In,Ga)Se2 absorber based thin film photovoltaic cell.

Project description:The physical data of the semiconductor materials used in the design of a CIGS absorber based thin film photovoltaic cell have been presented in this data article. Besides, the values of the contact parameter and operating conditions of the cell have been reported. Furthermore, by conducting the simulation with data corresponding to the device structure: soda-lime glass (SLG) substrate/Mo back-contact/CIGS absorber/CdS buffer/intrinsic ZnO/Al-doped ZnO window/Al-grid front-contact, the solar cell performance parameters such as open circuit voltage [Formula: see text], short circuit current density [Formula: see text], fill factor [Formula: see text], efficiency [Formula: see text], and collection efficiency [Formula: see text] have been analyzed.

| S-EPMC5328687 | biostudies-literature

Voids and compositional inhomogeneities in Cu(In,Ga)Se2 thin films: evolution during growth and impact on solar cell performance.

Project description:Structural defects such as voids and compositional inhomogeneities may affect the performance of Cu(In,Ga)Se2 (CIGS) solar cells. We analyzed the morphology and elemental distributions in co-evaporated CIGS thin films at the different stages of the CIGS growth by energy-dispersive x-ray spectroscopy in a transmission electron microscope. Accumulation of Cu-Se phases was found at crevices and at grain boundaries after the Cu-rich intermediate stage of the CIGS deposition sequence. It was found, that voids are caused by Cu out-diffusion from crevices and GBs during the final deposition stage. The Cu inhomogeneities lead to non-uniform diffusivities of In and Ga, resulting in lateral inhomogeneities of the In and Ga distribution. Two and three-dimensional simulations were used to investigate the impact of the inhomogeneities and voids on the solar cell performance. A significant impact of voids was found, indicating that the unpassivated voids reduce the open-circuit voltage and fill factor due to the introduction of free surfaces with high recombination velocities close to the CIGS/CdS junction. We thus suggest that voids, and possibly inhomogeneities, limit the efficiency of solar cells based on three-stage co-evaporated CIGS thin films. Passivation of the voids' internal surface may reduce their detrimental effects.

| S-EPMC6249540 | biostudies-literature

Aqueous-Solution-Processed Cu2ZnSn(S,Se)4 Thin-Film Solar Cells via an Improved Successive Ion-Layer-Adsorption-Reaction Sequence.

Project description:A facile improved successive ionic-layer adsorption and reaction (SILAR) sequence is described for the fabrication of Cu2ZnSn(S,Se)4 (CZTSSe) thin-film solar cells (TFSCs) via the selenization of a precursor film. The precursor films were fabricated using a modified SILAR sequence to overcome compositional inhomogeneity due to different adsorptivities of the cations (Cu+, Sn4+, and Zn2+) in a single cationic bath. Rapid thermal annealing of the precursor films under S and Se vapor atmospheres led to the formation of carbon-free Cu2ZnSnS4 (CZTS) and CZTSSe absorber layers, respectively, with single large-grained layers. The best devices based on CZTS and CZTSSe absorber layers showed total area (∼0.30 cm2) power conversion efficiencies (PCEs) of 1.96 and 3.74%, respectively, which are notably the first-demonstrated efficiencies using a modified SILAR sequence. Detailed diode analyses of these solar cells revealed that a high shunt conductance (G sh), reverse saturation current density (J o), and ideality factor (n d) significantly affected the PCE, open-circuit voltage (V oc), and fill factor (FF), whereas the short-circuit current density (J sc) was dominated by the series resistance (R s) and G sh. However, the diode analyses combined with the compositional and interface microstructural analyses shed light on further improvements to the device efficiency. The facile layer-by-layer growth of the kesterite CZTS-based thin films in aqueous solution provides a great promise as an environmentally benign pathway to fabricate a variety of multielement-component compounds with high compositional homogeneities.

| S-EPMC6645655 | biostudies-literature

Refractive indices of layers and optical simulations of Cu(In,Ga)Se2 solar cells.

Project description:Cu(In,Ga)Se2 based solar cells have reached efficiencies close to 23%. Further knowledge-driven improvements require accurate determination of the material properties. Here, we present refractive indices for all layers in Cu(In,Ga)Se2 solar cells with high efficiency. The optical bandgap of Cu(In,Ga)Se2 does not depend on the Cu content in the explored composition range, while the absorption coefficient value is primarily determined by the Cu content. An expression for the absorption spectrum is proposed, with Ga and Cu compositions as parameters. This set of parameters allows accurate device simulations to understand remaining absorption and carrier collection losses and develop strategies to improve performances.

| S-EPMC5954485 | biostudies-literature

Effect of the KF post-deposition treatment on grain boundary properties in Cu(In, Ga)Se2 thin films.

Project description:Significant power conversion efficiency improvements have recently been achieved for thin-film solar cells based on a variety of polycrystalline absorbers, including perovskites, CdTe, and Cu(In,Ga)Se2 (CIGS). The passivation of grain boundaries (GBs) through (post-deposition) treatments is a crucial step for this success. For the case of CIGS, the introduction of a potassium fluoride post-deposition treatment (KF-PDT) has boosted their power conversion efficiency to the best performance of all polycrystalline solar cells. Direct and indirect effects of potassium at the interface and interface-near region in the CIGS layer are thought to be responsible for this improvement. Here, we show that also the electronic properties of the GBs are beneficially modified by the KF-PDT. We used Kelvin probe force microscopy to study the effect of the KF-PDT on the CIGS surface by spatially resolved imaging of the surface potential. We find a clear difference for the GB electronic properties: the KF-PDT increases the band bending at GBs by about 70% and results in a narrower distribution of work function values at the GBs. This effect of the KF-PDT on the GB electronic properties is expected to contribute to the improved efficiency values observed for CIGS thin-film solar cells with KF-PDT.

| S-EPMC5269666 | biostudies-literature

Ultra-thin passivation layers in Cu(In,Ga)Se2 thin-film solar cells: full-area passivated front contacts and their impact on bulk doping.

Project description:In the search for highly transparent and non-toxic alternative front layers replacing state-of-the-art CdS in Cu(In,Ga)Se2 thin-film solar cells, alternatives rarely exceed reference devices in terms of efficiency. Full-area ultra-thin aluminium oxide tunnelling layers do not require any contact patterning and thus overcome the main drawback of insulating passivation layers. Even a few monolayers of aluminium oxide can be deposited in a controlled manner by atomic layer deposition, they show excellent interface passivation properties, low absorption, and suitable current transport characteristics on test devices. Depositing a ZnO-based transparent front contact, however, results in extremely poor solar cell performance. The issue is not necessarily a low quality of the alternative front layer, but rather the intricate relation between front layer processing and electronic bulk properties in the absorber layer. We identify three challenges critical for the development of novel front passivation approaches: (i) both Cd and Zn impurities beneficially reduce the high native net dopant concentration in the space charge region, (ii) sputter deposition of ZnO damages the passivation layer resulting in increased interface recombination, (iii) thermal treatments of devices with ZnO layer result in substantial Zn diffusion, which can penetrate the full absorber thickness already at moderate temperatures.

| S-EPMC7200765 | biostudies-literature

Direct evidence for grain boundary passivation in Cu(In,Ga)Se2 solar cells through alkali-fluoride post-deposition treatments.

Project description:The properties and performance of polycrystalline materials depend critically on the properties of their grain boundaries. Polycrystalline photovoltaic materials - e.g. hybrid halide perovskites, copper indium gallium diselenide (CIGSe) and cadmium telluride - have already demonstrated high efficiencies and promise cost-effective electricity supply. For CIGSe-based solar cells, an efficiency above 23% has recently been achieved using an alkali-fluoride post-deposition treatment; however, its full impact and functional principle are not yet fully understood. Here, we show direct evidence for the passivation of grain boundaries in CIGSe treated with three different alkali-fluorides through a detailed study of the nanoscale optoelectronic properties. We determine a correlation of the surface potential change at grain boundaries with the open-circuit voltage, which is supported by numerical simulations. Our results suggest that heavier alkali elements might lead to better passivation by reducing the density of charged defects and increasing the formation of secondary phases at grain boundaries.

| S-EPMC6726603 | biostudies-literature

Inkjet-Printed Cu2ZnSn(S, Se)4 Solar Cells.

Project description:Cu2ZnSn(S, Se)4-based solar cells with total area (0.5 cm2) power conversion efficiency of 6.4% are demonstrated from thin film absorbers processed by inkjet printing technology of Cu-Zn-Sn-S precursor ink followed by selenization. The device performance is limited by the low fill factor, which is due to the high series resistance.

| S-EPMC5115396 | biostudies-literature