Data supporting the morphological/topographical properties and the degradability on PET/PLA and PET/chitosan blends.
Ontology highlight
ABSTRACT:
SUBMITTER: Palma-Ramirez D
PROVIDER: S-EPMC6552015 | biostudies-literature | 2019 Aug
REPOSITORIES: biostudies-literature
Publications
Data supporting the morphological/topographical properties and the degradability on PET/PLA and PET/chitosan blends.
Palma-Ramírez D D Torres-Huerta A M AM Domínguez-Crespo M A MA Del Angel-López D D Flores-Vela A I AI de la Fuente D D
Data in brief 20190524
These data display evidence of the fracture through the morphologies and the topographical features as well as roughness data of different ratios of R(recycled)-PET/PLA, PET(virgin)/PLA, PET(virgin)/Chitosan and R(recycled)-PET/chitosan. Also, data of the morphologies after degradation under accelerated weathering test and degradation mechanisms are revealed. The data supplement the article "Comparative assessment of miscibility and degradability on PET/PLA and PET/chitosan blends". ...[more]
Similar Datasets
Project description:Poly(lactic acid) (PLA) is one of the most commonly employed synthetic biopolymers for facing plastic waste problems. Despite its numerous strengths, its inherent brittleness, low toughness, and thermal stability, as well as a relatively slow crystallization rate represent some limiting properties when packaging is its final intended application. In the present work, silver nanoparticles obtained from a facile and green synthesis method, mediated with chitosan as a reducing and stabilizing agent, have been introduced in the oligomeric lactic acid (OLA) plasticized PLA in order to obtain nanocomposites with enhanced properties to find potential application as antibacterial food packaging materials. In this way, the green character of the matrix and plasticizer was preserved by using an eco-friendly synthesis protocol of the nanofiller. The X-ray diffraction (XRD) and differential scanning calorimetry (DSC) results proved the modification of the crystalline structure as well as the crystallinity of the pristine matrix when chitosan mediated silver nanoparticles (AgCH-NPs) were present. The final effect over the thermal stability, mechanical properties, degradation under composting conditions, and antimicrobial behavior when AgCH-NPs were added to the neat plasticized PLA matrix was also investigated. The obtained results revealed interesting properties of the final nanocomposites to be applied as materials for the targeted application.
| S-EPMC7022492 | biostudies-literature
Project description:One of the methods of making traditional polymers more environmentally friendly is to modify them with natural materials or their biodegradable, synthetic equivalents. It was assumed that blends with polylactide (PLA), polysaccharides: chitosan (Ch) and starch (St) of branched polyurethane (PUR) based on synthetic poly([R,S]-3-hydroxybutyrate) (R,S-PHB) would degrade faster in the processes of hydrolysis and oxidation than pure PUR. For the sake of simplicity in the publication, all three modifiers: commercial PLA, Ch created by chemical modification of chitin and St are called bioadditives. The samples were incubated in a hydrolytic and oxidizing environment for 36 weeks and 11 weeks, respectively. The degradation process was assessed by observation of the chemical structure as well as the change in the mass of the samples, their molecular weight, surface morphology and thermal properties. It was found that the PUR samples with the highest amount of R,S-PHB and the lowest amount of polycaprolactone triol (PCLtriol) were degraded the most. Moreover, blending with St had the greatest impact on the susceptibility to degradation of PUR. However, the rate of weight loss of the samples was low, and after 36 weeks of incubation in the hydrolytic solution, it did not exceed 7% by weight. The weight loss of Ch and PLA blends was even smaller. However, a significant reduction in molecular weight, changes in morphology and changes in thermal properties indicated that the degradation of the samples should occur quickly after this time. Therefore, when using these polyurethanes and their blends, it should be taken into account that they should decompose slowly in their initial life. In summary, this process can be modified by changing the amount of R,S-PHB, the degree of cross-linking, and the type and amount of second blend component added (bioadditives).
| S-EPMC8068122 | biostudies-literature
Project description:Polymer blends of poly(butylene adipate-co-terephthalate) (PBAT) and polylactide (PLA) have been drawn attention due to the application potential as packaging or agricultural films. This study aims to determine the manufacturability, miscibility and mechanical properties of uncompatibilized PBAT/PLA blends prepared using different techniques. First, PBAT and PLA are melt-blended in a wide range of ratios from 90/10 to 10/90. The compounds are then processed into pressed panels, flat films and blown films. Finally, the thermal, morphological, rheological and mechanical properties of these blends are investigated. PBAT/PLA blends have a small difference of solubility parameters, predicting theoretically good miscibility. However, they show two almost unchanged glass transition temperatures in the DSC, phase separation in SEM and two relaxation mechanisms in the Cole-Cole plot. The phase morphology varies depending on both the blend ratios and the preparation techniques. Tensile tests indicate that with increasing PLA content the elongation at break decreases. A good correlation between the elongation at break and the tear propagation resistance is found. Furthermore, the trouser tear method is proven to be more applicable to differentiate highly extensible blown films compared with the Elmendorf tear method.
| S-EPMC7662590 | biostudies-literature
Project description:Poly(butylene adipate-co-terephthalate) (PBAT) was added to poly(lactic acid) (PLA)/lignin blends to decrease the considerable stiffness and brittleness of the blends. Two- and three-component blends were prepared in a wide composition range through homogenization in an internal mixer followed by compression molding. Interactions among the components were estimated by comparing the solubility parameters of the materials used and through thermal analysis. Mechanical properties were characterized by tensile testing. The structure of the blends was studied using scanning electron (SEM) and digital optical (DOM) microscopy. The results showed that the interactions between PBAT and lignin are somewhat stronger than those between PLA and the other two components. The maleic anhydride grafted PLA added as a coupling agent proved completely ineffective; it does not modify the interactions. The structural analysis confirmed the immiscibility of the components; the structure of the blends was heterogeneous at each composition. A dispersed structure formed when the concentration of one of the components was small, while, depending on lignin content, an interpenetrating network-like structure developed and phase inversion took place in the range of 30-60 vol% PBAT content. Lignin was located mainly in the PBAT phase. Properties were determined by the relative amount of PBAT and PLA; the addition of lignin deteriorated properties, mainly the deformability of the blends. Other means, such as reactive processing, must be used to improve compatibility and blend properties. The results contribute considerably to a better understanding of structure-property correlations in lignin-based hybrid blends.
| S-EPMC10422597 | biostudies-literature
Project description:Morphological and rheological properties of poly(lactic acid), PLA (semicrystalline and amorphous), and poly(butylene adipate-co-terephthalate), PBAT, and their blends (75 wt%/25 wt%; PLA/PBAT) were investigated in the presence of cellulose nanocrystals (CNCs) prepared from solution casting followed by melt mixing. For the solution casting step, the CNCs were either incorporated into the matrix, the dispersed phase, or both. The dispersion and distribution of the CNCs in the neat polymers and localization in their blends were analyzed via scanning electron microscopy (SEM) and atomic force microscopy (AFM). The highly dispersed CNCs in the solution cast nanocomposites were agglomerated after melt mixing. In the blends with 1 wt% CNCs, the nanoparticles were mostly localized on the surface of the PBAT droplets irrespective of their initial localization. The rheological behavior of the single polymer matrix nanocomposites and their blends was determined in dynamic and transient shear flow in the molten state. Upon melt mixing the complex viscosity and storage modulus of the solution cast nanocomposites decreased markedly due to re-agglomeration of the CNCs. Under shearing at 0.1 s-1, a significant droplet coalescence was observed in the neat blends, but was prevented by the presence of the CNCs at the interface in the blend nanocomposites.
| S-EPMC8065413 | biostudies-literature
Project description:Designing polymer structures and polymer blends opens opportunities to improve the performance of plastics. Blending poly(butylene adipate-co-terephthalate) (PBAT) and polylactide (PLA) is a cost-effective approach to achieve a new sustainable material with complementary properties. This study aimed to predict the theoretical miscibility of PBAT/PLA blends at the molecular level. First, the basic properties and the structure of PBAT and PLA are introduced, respectively. Second, using the group contribution methods of van Krevelen and Hoy, the Hansen and Hildebrand solubility parameters of PBAT and PLA were calculated, and the effect of the molar ratio of the monomers in PBAT on the miscibility with PLA was predicted. Third, the dependence of the molecular weight on the blend miscibility was simulated using the solubility parameters and Flory-Huggins theory. Next, the glass transition temperature of miscible PBAT/PLA blends, estimated using the Fox equation, is shown graphically. According to the prediction and simulation, the blends with a number-average molecular weight of 30 kg/mol for each component were thermodynamically miscible at 296 K and 463 K with the possibility of spinodal decomposition at 296 K and 30% volume fraction of PBAT. This study contributes to the strategic synthesis of PBAT and the development of miscible PBAT/PLA blends.
| S-EPMC8309548 | biostudies-literature
Project description:In this study, polymer blends with a mechanical property balance based on poly(lactic acid) (PLA), stiff polymer, and elongated polymer were developed. First, the binary blends PLA-elongated polymer [ethyl vinyl acetate (EVA) or polyethylene], or PLA-stiff polymer [polystyrene or poly(styrene-co-methyl methacrylate) (SMMA)] blends were studied using dynamic mechanic analysis (DMA) and analyzed using Minitab statistical software to determine the factors influencing the elongation or stiffness of the blends. Then, ternary blends such as elongation-poly(lactic acid)-stiff, were made from the binary blends that presented optimal performance. In addition, three blends [EVA-PLA-SMMA (EPS)] were elaborated by studying the mixing time (5, 15, and 15 min) and the added time of the SMMA (0, 0, and 10 min). Specifically, the mixing time for EPS 1, EPS 2, and EPS 3 is 5 min, 15 min, and 15 min (first EVA + PLA for 10 min, plus 5 min PLA-EVA and SMMA), respectively. Mechanical, thermal, rheological, and morphological properties of the blends were studied. According to DMA, the results show an increase in elongation at break (εb) and do not decrease the elastic module of poly(lactic acid). Nevertheless, EPS 3 excels in all properties, with an εb of 67% and modulus of elasticity similar to PLA. SMMA has a significant role as a compatibilizing agent and improves PLA processability.
| S-EPMC8703449 | biostudies-literature
Project description:This study investigated the effect of the Joncryl concentration on the properties of polylactide/poly(ε-caprolactone) (PLA/PCL) and PLA/poly(ethylene glycol) (PEG) blends. The addition of Joncryl influenced the properties of both PLA-based blends. In the blend of PLA/PCL blends, the addition of Joncryl reduced the size of PCL droplets, which implies the compatibility of the two phases, while PLA/PEG blends showed a co-continuous type of morphology at 0.1% and 0.3 wt.% of Joncryl loading. The crystallinity of PCL and PEG was studied on both PLA/PCL and PLA/PEG blend systems. In both scenarios, the crystallinity of the blends decreased upon the addition of Joncryl. Thermal stabilities were shown to depend on the addition of Joncryl. The toughness increased when 0.5 wt.% of Joncryl was added to both systems. However, the stiffness of PLA/PCL decreased, while the stiffness of PLA/PEG increased with the increasing concentration of Joncryl. This study provides new insight into the effect of chain extenders on the compatibility of PLA-based blends.
| S-EPMC10181129 | biostudies-literature
Project description:In this work, to fabricate a novel composite consisting of chitosan/poly-lactic acid doped with graphene oxide (CS/PLA-GO), composites were prepared via solution blending method to create various compositions of CS and PLA (90/10, 70/30 and 50/50CS/PLA-GO). Graphene oxide (GO) was added into a PLA solution prior to blending it with chitosan (CS). The surface morphology and structural properties of synthesized composites were characterized using FT-IR, SEM and XRD analysis. The performances of synthesized composites on thermal strength, mechanical strength, water absorption, and microbial activity were also evaluated through standard testing methods. The morphology of 70/30CS/PLA-GO became smoother with the addition of GO due to enhanced interfacial adhesion between CS, PLA and GO. The presence of GO has also improved the miscibility of CS and PLA and has superior properties compared to CS/PLA composites. Moreover, the addition of GO has boosted the thermal stability of the composite, with a significant enhancement of Td and Tg. The highest Td and Tg were accomplished at 389 °C and 76.88 °C, respectively, for the 70/30CS/PLA-GO composite in comparison to the CS and PLA that recorded Td at 272 °C and 325 °C and Tg at 61 °C and 60 °C, respectively. In addition, as reinforcement, GO provided a significant influence on the tensile strength of composites where the tensile modulus showed remarkable improvement compared to pure CS and CS/PLA composites. Furthermore, CS/PLA-GO composites showed excellent water-barrier properties. Among other compositions, 70/30CS/PLA revealed the greatest decrement in water absorption. From the antibacterial results, it was observed that 90/10CS/PLA-GO and 70/30CS/PLA-GO showed an inhibitory effect and had wide inhibition zones which were 8.0 and 8.5 mm, respectively, against bacteria Bacillus Subtillis B29.
| S-EPMC8199591 | biostudies-literature
Project description:Morphological characterization of chars from coal and bagasse plays an important role in both the burning efficiency and intrinsic reactivity of chars, during a combustion process [1], [2]. In this work, abundant data on the morphology of chars produced from coal and bagasse blends are presented. Char synthesis was performed varying the temperature (900, 1000 and 1100 °C) and bagasse proportion feeding (0, 25, 50, 75 and 100% w/w) in the pyrolysis reaction. Proximate, ultimate, petrographic and vitrinite reflectance of raw coal and bagasse are presented. Char morphology is classified into three groups -- thin walls, thick walls, and solid particles--, and results are exhibited. The data set is a comprehensive source for advancing in a further understanding of char's morphology from coal-bagasse blends.
| S-EPMC7109420 | biostudies-literature