Browse
Submit Data
Databases
API
Help

Dataset Information

24 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Percolative Composites with Carbon Nanohorns: Low-Frequency and Ultra-High Frequency Response.

ABSTRACT: We systematically studied the electromagnetic properties of carbon nanohorns (CNHs) and polystyrene composites filled with CNHs in static regime, low frequency and microwave regions. CNHs were synthesized using the direct current arc-discharge method using solid graphite rods and graphite rods filled by melamine mixed with graphite powder. Transmission electron microscopy and thermo-gravimetric analysis showed that CNH agglomerates are the main product, while the addition of melamine promotes the formation of graphite balls. Graphitic contamination causes the internal leakage of inter-agglomerate capacity, lowering the permittivity and enhancing the conductivity of composites. The permittivity of CNH/polystyrene composites increases with the filler fraction, and near the dielectric threshold electromagnetic characteristics of the composites exhibit critical behaviour. Our results suggest that CNHs with relatively high values of permittivity and contact resistance could be used as high-k materials.

SUBMITTER: Sedelnikova OV

PROVIDER: S-EPMC6600986 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Preparation and Mechanical Behavior of Ultra-High Strength Low-Carbon Steel.

Project description:The low-carbon steel (~0.12 wt%) with complete martensite structure, obtained by quenching, was cold rolled to get the high-strength steel sheets. Then, the mechanical properties of the sheets were measured at different angles to the rolling direction, and the microstructural evolution of low-carbon martensite with cold rolling reduction was observed. The results show that the hardness and the strength gradually increase with increasing rolling reduction, while the elongation and impact toughness obviously decrease. The strength of the sheets with the same rolling reduction are different at the angles of 0°, 45°, and 90° to the rolling direction. The tensile strength (elongation) along the rolling direction is higher than that in the other two directions, but the differences between them are not obvious. When the aging was performed at a low temperature, the strength of the initial martensite and deformed martensite increased with increasing aging time during the early stages of aging, followed by a gradual decrease with further aging. However, the elongation increases with increasing aging time. The change of hardness is consistent with that of strength for the cold-rolled martensite, while the hardness of the initial martensite decreases gradually with increasing aging time.

| S-EPMC7013394 | biostudies-literature

Structural Study of Sulfur-Added Carbon Nanohorns.

Project description:In the past few decades, nanostructured carbons (NCs) have been investigated for their interesting properties, which are attractive for a wide range of applications in electronic devices, energy systems, sensors, and support materials. One approach to improving the properties of NCs is to dope them with various heteroatoms. This work describes the synthesis and study of sulfur-added carbon nanohorns (S-CNH). Synthesis of S-CNH was carried out by modified chemical vapor deposition (m-CVD) using toluene and thiophene as carbon and sulfur sources, respectively. Some parameters such as the temperature of synthesis and carrier gas flow rates were modified to determine their effect on the properties of S-CNH. High-resolution scanning and transmission electron microscopy analysis showed the presence of hollow horn-type carbon nanostructures with lengths between 1 to 3 µm and, diameters that are in the range of 50 to 200 nm. Two types of carbon layers were observed, with rough outer layers and smooth inner layers. The surface textural properties are attributed to the defects induced by the sulfur intercalated into the lattice or bonded with the carbon. The XRD patterns and X-ray microanalysis studies show that iron serves as the seed for carbon nanohorn growth and iron sulfide is formed during synthesis.

| S-EPMC9148090 | biostudies-literature

Bio-Inspired Aggregation Control of Carbon Nanotubes for Ultra-Strong Composites.

Project description:High performance nanocomposites require well dispersion and high alignment of the nanometer-sized components, at a high mass or volume fraction as well. However, the road towards such composite structure is severely hindered due to the easy aggregation of these nanometer-sized components. Here we demonstrate a big step to approach the ideal composite structure for carbon nanotube (CNT) where all the CNTs were highly packed, aligned, and unaggregated, with the impregnated polymers acting as interfacial adhesions and mortars to build up the composite structure. The strategy was based on a bio-inspired aggregation control to limit the CNT aggregation to be sub 20-50 nm, a dimension determined by the CNT growth. After being stretched with full structural relaxation in a multi-step way, the CNT/polymer (bismaleimide) composite yielded super-high tensile strengths up to 6.27-6.94 GPa, more than 100% higher than those of carbon fiber/epoxy composites, and toughnesses up to 117-192 MPa. We anticipate that the present study can be generalized for developing multifunctional and smart nanocomposites where all the surfaces of nanometer-sized components can take part in shear transfer of mechanical, thermal, and electrical signals.

| S-EPMC4476433 | biostudies-literature

Radiation and electrostatic resistance for ultra-stable polymer composites reinforced with carbon fibers.

Project description:Future space travel needs ultra-lightweight and robust structural materials that can withstand extreme conditions with multiple entry points to orbit to ensure mission reliability. This is unattainable with current inorganic materials. Ultra-highly stable carbon fiber reinforced polymers (CFRPs) have shown susceptibility to environmental instabilities and electrostatic discharge, thereby limiting the full lightweight potential of CFRP. A more robust and improved CFRP is needed in order to improve space travel and structural engineering further. Here, we address these challenges and present a superlattice nano-barrier-enhanced CFRP with a density of ~3.18 g/cm3 that blends within the mechanical properties of the CFRP, thus becoming part of the composite itself. We demonstrate composites with enhanced radiation resistance coupled with electrical conductivity (3.2 × 10-8 ohm⋅m), while ensuring ultra-dimensionally stable physical properties even after temperature cycles from 77 to 573 K.

| S-EPMC10022895 | biostudies-literature

MIPP-Seq: Ultra-sensitive rapid detection and validation of low-frequency mosaic mutations

Project description:MIPP-Seq provides an ultra-sensitive, low-cost approach for detecting and validating known and novel mutations in a highly scalable system with broad utility spanning both research and clinical diagnostic testing applications. The scalability of MIPP-Seq allows for multiplexing mutations and samples, which dramatically reduce costs of variant validation when compared to methods like ddPCR. By leveraging the power of individual analyses of multiple unique and independent reactions, MIPP-Seq can validate and precisely quantitate extremely low AAFs across multiple tissues and mutational categories including both indels and SNVs. Furthermore, using Illumina sequencing technology, MIPP-seq provides a robust method for accurate detection of novel mutations at an extremely low AAF.

2021-01-30 | GSE165780 | GEO

Single-Walled Carbon Nanohorns as Boosting Surface for the Analysis of Low-Molecular-Weight Compounds by SALDI-MS.

Project description:Limits of Matrix-Assisted Laser Desorption Ionization (MALDI) mass spectrometry (MS) in the study of small molecules are due to matrix-related interfering species in the low m/z range. Single-walled carbon nanohorns (SWCNH) were here evaluated as a specific surface for the rapid analysis of amino acids and lipids by Surface-Assisted Laser Desorption Ionization (SALDI). The method was optimized for detecting twenty amino acids, mainly present as cationized species, with the [M+K]+ response generally 2-time larger than the [M+Na]+ one. The [M+Na]+/[M+K]+ signals ratio was tentatively correlated with the molecular weight, dipole moment and binding affinity, to describe the amino acids' coordination ability. The SWCNH-based surface was also tested for analyzing triglycerides in olive oil samples, showing promising results in determining the percentage composition of fatty acids without any sample treatment. Results indicated that SWCNH is a promising substrate for the SALDI-MS analysis of low molecular weight compounds with different polarities, enlarging the analytical platforms for MALDI applications.

| S-EPMC9100638 | biostudies-literature

Molecular Dynamics Modeling of Interfacial Interactions between Flattened Carbon Nanotubes and Amorphous Carbon: Implications for Ultra-Lightweight Composites.

Project description:Flattened carbon nanotubes (flCNTs) naturally form in many carbon nanotube-based materials and can exhibit mechanical properties similar to round carbon nanotubes but with tighter packing and alignment. To facilitate the design, fabrication, and testing of flCNT-based composites for aerospace structures, computational modeling can be used to efficiently and accurately predict their performance as a function of processing parameters, such as reinforcement/matrix cross-linking. In this study, molecular dynamics modeling is used to predict the load transfer characteristics of the interface region between the flat region of flCNTs (i.e., bi-layer graphene) and amorphous carbon (AC) with various levels and locations of covalent bond cross-linking and AC mass density. The results of this study show that increasing the mass density of AC at the interface improves the load transfer capability of the interface. However, a much larger improvement is observed when cross-linking is added both to the flCNT-AC interface and between the flCNT sheets. With both types of cross-linking, substantial improvements in interfacial shear strength, transverse tension strength, and transverse tension toughness are predicted. The results of this study are important for optimizing the processing of flCNT/AC composites for demanding engineering applications.

| S-EPMC9039962 | biostudies-literature

Hydrocarbon Resin-Based Composites with Low Thermal Expansion Coefficient and Dielectric Loss for High-Frequency Copper Clad Laminates.

Project description:The rapid development of the 5G communication technology requires the improvement of the thermal stability and dielectric performance of high-frequency copper clad laminates (CCL). A cyclic olefin copolymer (COC) resin was added to the original 1,2-polybutadienes (PB)/styrene ethylene butylene styrene (SEBS) binary resin system to construct a PB/SEBS/COC ternary polyolefin system with optimized dielectric properties, mechanical properties, and water absorption. Glass fiber cloths (GFCs) and SiO2 were used to fill the resin matrix so to reduce the thermal expansion coefficient (CTE) and enhance the mechanical strength of the composites. It was found that the CTE of polyolefin/GFCs/SiO2 composite laminates decreased with the increase of SiO2 loading at first, which was attributed to the strong interfacial interaction restricting the segmental motion of polymer chains between filler and matrix. It was obvious that the addition of COC and SiO2 had an effect on the porosity, as shown in the SEM graph, which influenced the dielectric loss (Df) of the composites directly. When the weight of SiO2 accounted for 40% of the total mass of the composites, the laminates exhibited the best comprehensive performance. Their CTE and Df were reduced by 63.3% and 22.0%, respectively, and their bending strength increased by 2136.1% compared with that of the substrates without COC and SiO2. These substrates have a great application prospect in the field of hydrocarbon resin-based CCL.

| S-EPMC9182675 | biostudies-literature

Ultra-low frequency labeling of single cell lineages in Drosophila.

Project description:We describe a new methodology for genetically labeling single cell lineages in Drosophila called DMARCM. The system offers ultra-low frequency labeling, linear induction, consistent labeling among individuals and virtually no background signal. We compare this technique to an existing approach, which has been widely adopted. We demonstrate how application of DMARCM in the gastrointestinal epithelium permits the effects of labeling frequency on tumorigenic stem cell growth to be distinguished in an established tumor model.

| S-EPMC7205028 | biostudies-literature

Ultra High-Speed Radio Frequency Switch Based on Photonics.

Project description:Microwave switches, or Radio Frequency (RF) switches have been intensively used in microwave systems for signal routing. Compared with the fast development of microwave and wireless systems, RF switches have been underdeveloped particularly in terms of switching speed and operating bandwidth. In this paper, we propose a photonics based RF switch that is capable of switching at tens of picoseconds speed, which is hundreds of times faster than any existing RF switch technologies. The high-speed switching property is achieved with the use of a rapidly tunable microwave photonic filter with tens of gigahertz frequency tuning speed, where the tuning mechanism is based on the ultra-fast electro-optics Pockels effect. The RF switch has a wide operation bandwidth of 12 GHz and can go up to 40 GHz, depending on the bandwidth of the modulator used in the scheme. The proposed RF switch can either work as an ON/OFF switch or a two-channel switch, tens of picoseconds switching speed is experimentally observed for both type of switches.

| S-EPMC4660296 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data