Dataset Information

Influence of Plastic Strain Accumulation in Continuous Ingots during ECAP on Structure and Recrystallization Temperature of AlCu4MgSi Alloy.

ABSTRACT: This work attempts to process AlCu4MgSi (AW 2017A) alloy continuous ingots by means of the equal channel angular pressing (ECAP) method. The equal channel angular pressing (ECAP) technique has been widely investigated in recent years as the most promising severe plastic deformation (SPD) method. The presented research was focused on the precise determination of the phase composition of the precipitates formed in the AlCu4MgSi alloy and its influence on intensive plastic deformation. In the second stage, the research was focused on explaining the recrystallization process. With the use of the high-temperature X-ray diffraction (HTXRD) technique, the changes in the dislocation substructure at various recrystallization annealing temperatures were analyzed.

SUBMITTER: Nuckowski PM

PROVIDER: S-EPMC7040609 | biostudies-literature | 2020 Jan

REPOSITORIES: biostudies-literature

ACCESS DATA

Publications

Influence of Plastic Strain Accumulation in Continuous Ingots during ECAP on Structure and Recrystallization Temperature of AlCu4MgSi Alloy.

Nuckowski Paweł M PM Snopiński Przemysław P Wróbel Tomasz T

Materials (Basel, Switzerland) 20200125 3

This work attempts to process AlCu4MgSi (AW 2017A) alloy continuous ingots by means of the equal channel angular pressing (ECAP) method. The equal channel angular pressing (ECAP) technique has been widely investigated in recent years as the most promising severe plastic deformation (SPD) method. The presented research was focused on the precise determination of the phase composition of the precipitates formed in the AlCu4MgSi alloy and its influence on intensive plastic deformation. In the secon ...[more]

PMID: 31991833

Similar Datasets

Project description:Plastic deformation of low/high density polyethylene (LDPE/HDPE) was analyzed in this work using positron annihilation lifetime spectroscopy (PALS). It was shown that in undeformed LDPE, both the mean ortho-positronium lifetime (τ3) and its dispersion (σ3), corresponding to the average size and size distribution of the free-volume pores of the amorphous component, respectively, were clearly higher than in HDPE. This effect was induced by a lower and less uniform molecular packing of the amorphous regions in LDPE. During the deformation of LDPE, an increase in the τ3 value was observed within the local strains of 0-0.25. This effect was mainly stimulated by a positive relative increase in interlamellar distances due to the deformation of lamellar crystals oriented perpendicular (increased by 31.8%) and parallel (decreased by 10.1%) to the deformation directions. At the same time, the dimension of free-volume pores became more uniform, which was manifested by a decrease in the σ3 value. No significant effect of temperature or strain rate on the τ3 and σ3 values was observed during LDPE deformation. In turn, in the case of HDPE, with an increase in the strain rate/or a decrease in temperature, an intensification of the cavitation phenomenon could be observed with a simultaneous decrease in the τ3 value. This effect was caused by the lack of annihilation of ortho-positonium (o-Ps) along the longer axis of the highly anisotropic/ellipsoidal cavities. Therefore, this dimension was not detectable by the PALS technique. At the same time, the increase in the dimension of the shorter axis of the cavities was effectively limited by the thickness of amorphous layers. As the strain rate increased or the temperature decreased, the σ3 value during HDPE deformation increased. This change was correlated with the initiation and intensification of the cavitation phenomenon. Based on the mechanical response of samples with a similar yield stress, it was also proven that the susceptibility of the amorphous regions of LDPE to the formation of cavities is lower than in the case of amorphous component of HDPE.

Dataset Information

Influence of Plastic Strain Accumulation in Continuous Ingots during ECAP on Structure and Recrystallization Temperature of AlCu4MgSi Alloy.

Publications

Influence of Plastic Strain Accumulation in Continuous Ingots during ECAP on Structure and Recrystallization Temperature of AlCu4MgSi Alloy.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets