Browse
Submit Data
Databases
API
Help

Dataset Information

7 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Microwave-Assisted Preparation of Activated Carbon Modified by Zinc Chloride as a Packing Material for Column Separation of Saccharides.

ABSTRACT: Activated carbon, an amorphous carbon material with a high specific surface area and void fraction, is widely used as an economical adsorbent in many fields. In this work, a kind of new activated carbon composite for saccharide column separation was prepared by zinc chloride impregnating and microwave heating. The structural characterizations validate the increase in porosity and the specific surface area of the activated carbon as well as the change of the activated carbon crystallite lattice. The chemical characterizations validate the increase in the number of oxygen-containing functional groups and structural bonding of zinc with the activated carbon surface. Compared with the blank control, the surface Zn element improves the adsorption selectivity of the activated carbon to the target saccharides. Under the special mechanism of microwaves, the pores created by expansion from the inside to the outside facilitate the free flow of the mobile phase. The eight saccharides can be separated by the columns packed with the activated carbon impregnated with 40% and 70% zinc chloride.

SUBMITTER: Liu Z

PROVIDER: S-EPMC7203912 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Facile Microwave-assisted Synthesis Manganese Doped Zinc Sulfide Nanoparticles.

Project description:Undoped and manganese doped zinc sulfide nanoparticles were produced by a fast, one-step and two-component microwave-assisted synthesis method. The solid phase retains around 78% of the initial Mn concentration, as revealed by Particle Induced X-ray Emission analysis. X-ray diffraction patterns confirmed zinc blende structure and in the transmission electron microscopy images, nanoparticles with triangular prism and cube shapes were observed, respectively with an average particle size around 7?nm and 13?nm. Dried powders of zinc sulfide nanoparticles, doped with 0.1?mol% and 0.7?mol% of Mn ions, show highest brilliance of luminescence under UV light. Increasing dopant levels resulted in a diminishing emission that vanishes above 4% of dopant concentration. The synthesis of ZnS was monitored and two main events were detected, one at 145?°C corresponding to the sol-gel phase formation and another after ~3?min at 300?°C where the precipitation of the zinc sulfide nanoparticles occurs.

| S-EPMC6207788 | biostudies-literature

Microwave-Assisted Preparation of Organo-Lead Halide Perovskite Single Crystals.

Project description:The efficiency of organo-lead halide perovskite-based optoelectronic devices is dramatically lower for amorphous materials compared to highly crystalline ones. Therefore, it is challenging to optimize and scale up the production of large-sized single crystals of perovskite materials. Here, we describe a novel and original approach to preparing lead halide perovskite single crystals by applying microwave radiation during the crystallization. The microwave radiation primarily causes precise heating control in the whole volume and avoids temperature fluctuations. Moreover, this facile microwave-assisted method of preparation is highly reproducible and fully automated, it and can be applied for various different perovskite structures. In addition, this cost-effective method is expected to be easily scalable because of its versatility and low energy consumption. The crystallization process has low heat losses; therefore, only a low microwave reactor power of 8-15 W during the temperature changes and of less than 1 W during the temperature holding is needed.

| S-EPMC7059302 | biostudies-literature

Ultrasound-assisted of alkali chloride separation using bulk ionic liquid membrane.

Project description:An ultrasonic-assisted separation of alkali chloride (LiCl, NaCl, and KCl) salts have been carried out using of an hydrophobic ionic liquid membrane (ILM). The ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate and tributyl phosphate mixture have been used as ILM. An ultrasonic probe with different frequencies (25, 100, and 250) kHz have been applied as source of ultrasound generator with different times of sonication (2, 5, and 10) min in three phases system containing feed, ILM, and receiver in osmotic U-shaped tube. Also, 250, 500, and 1000 ppm of the feed (alkali chloride) concentration have been used to separate. The frequency of 250 kHz with higher sonication time provides optimum condition for separation of LiCl with lower feed concentration. The thermodynamic properties such as density and speed of sound and the related thermodynamic properties have been calculated to optimize ILM composition (xIL = 0.45) for ultrasound-separation.

| S-EPMC8091055 | biostudies-literature

Microwave assisted synthesis and characterisation of a zinc oxide/tobacco mosaic virus hybrid material. An active hybrid semiconductor in a field-effect transistor device.

Project description:Tobacco mosaic virus (TMV) has been employed as a robust functional template for the fabrication of a TMV/zinc oxide field effect transistor (FET). A microwave based approach, under mild conditions was employed to synthesize stable zinc oxide (ZnO) nanoparticles, employing a molecular precursor. Insightful studies of the decomposition of the precursor were done using NMR spectroscopy and material characterization of the hybrid material derived from the decomposition was achieved using dynamic light scattering (DLS), transmission electron microscopy (TEM), grazing incidence X-ray diffractometry (GI-XRD) and atomic force microscopy (AFM). TEM and DLS data confirm the formation of crystalline ZnO nanoparticles tethered on top of the virus template. GI-XRD investigations exhibit an orientated nature of the deposited ZnO film along the c-axis. FET devices fabricated using the zinc oxide mineralized virus template material demonstrates an operational transistor performance which was achieved without any high-temperature post-processing steps. Moreover, a further improvement in FET performance was observed by adjusting an optimal layer thickness of the deposited ZnO on top of the TMV. Such a bio-inorganic nanocomposite semiconductor material accessible using a mild and straightforward microwave processing technique could open up new future avenues within the field of bio-electronics.

| S-EPMC4419583 | biostudies-literature

Microwave-Assisted Catalytic Degradation of Brilliant Green by Spinel Zinc Ferrite Sheets.

Project description:Microwave (MW)-assisted catalytic degradation, being an emerging technique, can potentially fill in the technological gap which promises on-demand, prompt, and efficient catalysis, and therefore, suitable MW catalysts are curiously being hunted. Candidature of spinel zinc ferrite (SZFO) atomic sheets as a MW catalyst has thoroughly been investigated in this article. Analytical techniques prove SZFO atomic sheets to be highly crystalline, thermally stable, good dielectric, and superparamagnetic, which render it a potentially strong MW catalyst. Brilliant green (BG) has been demonstrated to be chemisorbed on the SZFO atomic sheets, which upon MW irradiation gets mineralized within 5 min, and the overall efficiency has been observed to be >99%. Total organic carbon removal of ∼80% has been obtained. Ionic chromatography proves the formation of SO4 2- and NO3 - anions which increase with MW exposure time. Liquid chromatography mass spectroscopy studies have established intermediate formations during catalysis. SZFO, established as a uniquely suited and highly efficient MW catalyst for BG, is expected to broaden the horizons of MW-assisted catalytic degradation and lead it toward its broader applications.

| S-EPMC6648797 | biostudies-literature

Superparamagnetic and Perfect-Paramagnetic Zinc Ferrite Quantum Dots from Microwave-Assisted Tunable Synthesis.

Project description:The properties of quantum dot (QD)-size material depend directly upon its unit cell structure. Spinel zinc ferrite QD powder is produced via a one-pot microwave-assisted hydrothermal synthesis for just 5 min. Varying initial pH values of the preparation sol from 6 to 12 enlarges the Zn/Fe atomic ratio (by ca. 10%), unit cell volume (by ca. 0.5%), particle size (3.5-4.5 nm), and degree of inversion. This leads to a change in the magnetic behavior of the QD-size zinc ferrite from a superparamagnetic to a perfect-paramagnetic type. This novel finding points that the significant changes in the inherent structural parameters of spinel ZnFe2O4 QDs (Zn/Fe ratio and degree of inversion) induced by the systematic pH change of the preparation sol are exclusively responsible for the observed unique magnetic behavior instead of mere QD (single domain) nanosizes.

| S-EPMC9453939 | biostudies-literature

Microwave-Assisted Sol-Gel Preparation of the Nanostructured Magnetic System for Solid-Phase Synthesis.

Project description:This work describes a new synthesis method for core-shell magnetite nanoparticles with a secondary silica shell, functionalized with a linker system (Fe3O4-PABA-SiO2-linker) using a microwave-assisted heating technique. The functionalized solid nanomaterial was used for the nanophase synthesis of peptides (Fmoc route) as a solid support. The co-precipitation method was selected to obtain magnetite nanoparticles and sol-gel technique for silica coating using a microwave-assisted (MW) procedure. The magnetic properties of the nanoparticle core offer the advantage of a quick and easy alternative for the magnetic separation of the product from the reaction mixture, facilitating all the intermediary washing and separation operations. The intermediate and final materials were analyzed by advanced characterization methods. The effectiveness of the nanophase peptide synthesis using this nanostructured material as solid support was demonstrated for a short peptide sequence.

| S-EPMC8709383 | biostudies-literature

Microwave-assisted synthesis of isosorbide-derived diols for the preparation of thermally stable thermoplastic polyurethane.

Project description:In order to prepare thermally stable isosorbide-derived thermoplastic polyurethane, the synthesis of two new chiral exo-exo configured diols, prepared from isosorbide, and two types of diphenols (bisphenol A and thiodiphenol) was described. The synthesis conditions were optimized under conventional heating and microwave irradiations. To prove their suitability in polymerization, these monomers were successfully polymerized using 4,4'-diphenylmethane diisocyanate (MDI) and hexamethylene diisocyanate (HDI). Both monomers and polymers have been studied by NMR, FT-IR, TGA, DSC; intrinsic viscosity of polymers has also been determined. The results showed the effectiveness of the synthetic strategy proposed; moreover, a dramatic reduction of the reaction time and an important improvement of the monomers yield using microwave irradiation have been demonstrated. The monomers, as well as the polymers, showed excellent thermal stability both in air and nitrogen. It was also shown that the introduction of sulphur in the polyurethane backbone was effective in delaying the onset of degradation as well as the degradation rate.

| S-EPMC5812175 | biostudies-literature

Copper-/Zinc-Doped TiO<sub>2</sub> Nanopowders Synthesized by Microwave-Assisted Sol-Gel Method.

Project description:Using the microwave-assisted sol-gel method, Zn- and Cu-doped TiO2 nanoparticles with an anatase crystalline structure were prepared. Titanium (IV) butoxide was used as a TiO2 precursor, with parental alcohol as a solvent and ammonia water as a catalyst. Based on the TG/DTA results, the powders were thermally treated at 500 °C. XRD and XRF revealed the presence of a single-phase anatase and dopants in the thermally treated nanoparticles. The surface of the nanoparticles and the oxidation states of the elements were studied using XPS, which confirmed the presence of Ti, O, Zn, and Cu. The photocatalytic activity of the doped TiO2 nanopowders was tested for the degradation of methyl-orange (MO) dye. The results indicate that Cu doping increases the photoactivity of TiO2 in the visible-light range by narrowing the band-gap energy.

| S-EPMC10137937 | biostudies-literature

Ultrasonic assisted rapid preparation of superhydrophobic stainless steel surface and its application in oil/water separation.

Project description:The preparation of superhydrophobic (SH) surface on stainless steel by chemical etching method is challenging due to the good corrosion resistance of the material. In this work, SH surface with water contact angle (WCA) as high as 163.21° was accomplished on 304 stainless steel surface by a rapid ultrasonic-assisted chemical etching method within 7 min and a low-cost fluorine-free modification treatment. The mechanism of ultrasonic field on the etching process was explored by detecting the cavitation and oscillation energy in the reactor. It is the first time to found that the ultrasonic cavitation effect enhanced the etching process by both chemical and physical facilitation resulting in hierarchical lamellar micro-structures, "mountain-like" micro-structure clusters and "coral-reef-like" nano-scale structures on the surface. With the ultrasonic power increasing, the ultrasonic cavitation effect not only enhanced the superhydrophobicity of sample surface, but also improved the uniformity of surface wettability. The samples also showed excellent performance of oil/water separation for various organics (all separation efficiencies up to 96%) and remarkable mechanical stability.

| S-EPMC8637139 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data