Data for experimental and calculated values of the adsorption of Pb(II) and Cr(VI) on APTES functionalized magnetite biochar using Langmuir, Freundlich and Temkin equations
Ontology highlight
ABSTRACT:
SUBMITTER: Nnadozie E
PROVIDER: S-EPMC7509373 | biostudies-literature | 2020 Sep
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Biochar is preferentially recommended for the remediation of heavy metal-polluted soils. Sunflower is an important high-biomass oil crop with a promising potential for phytoremediation of Cr(VI)-polluted soil. However, how biochar affects sunflower growth and Cr accumulation in Cr(VI)-polluted soil needs to be elucidated. Here, a pot culture experiment was conducted to study whether soil amendment with biochar (0, 0.1%, 1%, and 5%, w/w) can mitigate Cr toxicity and accumulation in sunflower seedlings grown in soils artificially polluted with different levels of Cr(VI) (0, 50, and 250 mg Cr(VI)/kg soil). The addition of Cr(VI) exhibited significant phytotoxicity, as evidenced by inhibited plant growth and even the death of seedlings at 250 mg/kg Cr(VI). Overall, biochar amendment showed positive effects on plant growth and Cr immobilization, dependent on both the biochar dose and Cr addition level. When 50 mg/kg Cr(VI) was added, 1% biochar showed positive effects similar to 5% biochar on improving plant growth and mineral nutrition (particularly K), reducing Cr content in shoots and roots, and decreasing Cr availability and Cr(VI) content in the soil. In comparison with non-amendment, 1% and 5% biochar caused 85% and 100% increase in shoot dry weights, and 75% and 86% reduction in shoot Cr concentrations, respectively. When 250 mg/kg Cr(VI) was added, a 5% dose produced much better benefits than 1%, while a 0.1% dose did not help plants to survive. Overall, an appropriate dose of biochar enhanced Cr(VI) immobilization and subsequently decreased its toxicity and accumulation in sunflower seedlings. Our findings confirm that biochar can be used as an efficient amendment for the remediation of Cr(VI)-polluted soils and cleaner production of sunflower oil and biomass.
| S-EPMC10536207 | biostudies-literature
Project description:By utilizing the synergistic effect of chitosan (CS), magnetite (Fe3O4) particles, and graphene oxide (GO), a series of efficient and eco-friendly chitosan/magnetite-graphene oxide (CS/MGO) composites were fabricated through a facile chemical route. First, Fe3O4 particles were chemically deposited on the surface of GO to fabricate MGO hybrid. Then, chitosan was attached on MGO sheets, assembling to CS/MGO composites. According to the results of characterization, the covalent Fe-O-C bonds, electrostatic attraction, and hydrogen bonding between GO, Fe3O4, and chitosan ensure excellent structural stability and physico-chemical properties. The adsorption of Cr(VI) onto CS/MGO composites was also carried out under various conditions (content of CS, pH, initial concentration, contact time, and temperature). The CS/MGO composites possess high removal capacity for Cr(VI) from aqueous solution. Moreover, results also suggested that the CS/MGO composites had a strong reducing action for Cr(VI). When adsorption occurred, Cr(VI) and Cr(III) were simultaneously removed by CS/MGO composites. In addition, CS/MGO composites could retain good Cr(VI) removal efficiency after reuse over five cycles. CS/MGO composites are expected to have potential applications as easily regenerative bioadsorbents for Cr(VI) polluted water cleanup.
| S-EPMC6193940 | biostudies-literature
Project description:We prepared a novel adsorbent functionalized by bagasse magnetic biochar (BMBC). To study the removal behaviors and mechanisms of Cr(VI) by BMBC, batch adsorption experiments were conducted by modifying variables, such as pH, adsorption time, BMBC dosages, initial Cr concentration, co-existing ions, and ionic strength, and characterizing BMBC before and after Cr(VI) adsorption. BMBC was primarily composed of Fe2O3 and Fe3O4 on bagasse boichar with an amorphous structure. The specific surface area of BMBC was 81.94 m2 g-1, and the pHpzc of BMBC was 6.2. The fabricated BMBC showed high adsorption performance of Cr(VI) in aqueous solution. The maximum Cr(VI) adsorption capacity of BMBC was 29.08 mg g-1 at 25 ºC, which was much higher than that of conventional biochar sorbents. The adsorption process followed pseudo-second-order kinetics and could be explained by the involvement of the Langmuir isotherm in monolayer adsorption. The crystalline structure of Fe3O4 in the BMBC changed slightly during the adsorption process; Fe3O4 improved the adsorption of Cr(VI) on BMB. The desorption capacity of Cr(VI) was 8.21 mg g-1 when 0.2 mol L-1 NaOH was used as the desorption solution. After being reused three times, the removal efficiency is still as high as 80.36%.
| S-EPMC7722720 | biostudies-literature
Project description:This study details the preparation of Fe-Mn binary oxide/mulberry stem biochar composite adsorbent (FM-MBC) from mulberry stems via the multiple activation by potassium permanganate, ferrous chloride, triethylenetetramine, and epichlorohydrin. The characteristics of FM-MBC had been characterized by SEM-EDS, BET, FT-IR, XRD, and XPS, and static adsorption batch experiments such as pH, adsorption time, were carried out to study the mechanism of Cr(VI) adsorption on FM-MBC and the impact factors. The results indicated that in contrast with the mulberry stem biochar (MBC), the FM-MBC has more porous on surface with a BET surface area of 74.73 m2/g, and the surface loaded with α-Fe2O3 and amorphization of MnO2 particles. Besides, carboxylic acid, hydroxyl, and carbonyls functional groups were also formed on the FM-MBC surface. At the optimal pH 2.0, the maximum adsorption capacity for Cr(VI) was calculated from the Langmuir model of 28.31, 31.02, and 37.14 mg/g at 25, 35, and 45 °C, respectively. The aromatic groups, carboxyls, and the hydroxyl groups were the mainly functional groups in the adsorption of Cr(VI). The mechanism of the adsorption process of FM-MBC for Cr(VI) mainly involves electrostatic interaction, surface adsorption of Cr(VI) on FM-MBC, and ion exchange.
| S-EPMC7036895 | biostudies-literature
Project description:Graphene oxide/polyamidoamine dendrimers (GO/PAMAMs) composites were used to remove Cr(VI) from simulated effluents, the adsorption kinetics and thermodynamics of Cr(VI) onto GO/PAMAMs were systematically investigated. The results showed that the optimum pH value was 2.5, the removal percentage reached 90.7% for 30 mg/L of Cr(VI) within 120 min. The adsorption process was well described by pseudo-second-order kinetic model. The maximum adsorption capacities of Cr(VI) onto GO/PAMAMs were found to be 131.58, 183.82 and 211.42 mg/g at 293.15, 303.15 and 313.15 K, respectively, which were calculated from the Langmuir model equation. The adsorption thermodynamic parameters indicate that the adsorption of Cr(VI) onto GO/PAMAMs is a spontaneous endothermic process. The XPS analysis reveals the adsorption and removal mechanism of Cr(VI) on GO/PAMAMs that first the Cr(VI) binds to the protonated amine of GO/PAMAMs, then Cr(VI) be reduced to Cr(III) with the assistance of π-electrons on the carbocyclic six-membered ring of GO in GO/PAMAMs, and then Cr(III) was released into solution under the electrostatic repulsion between the Cr(III) and the protonated amine groups.
| S-EPMC6403246 | biostudies-other
Project description:It is challenging work to develop a low-cost, efficient, and environmentally friendly Cr(VI) adsorbent for waste water treatment. In this paper, we used hemicelluloses from chemical fiber factory waste as the raw material, and prepared two kinds of carbon materials by the green hydrothermal method as adsorbent for Cr(VI). The results showed that hemicelluloses hydrothermally treated with citric acid (HTC) presented spherical shapes, and hemicelluloses hydrothermally treated with ammonia solution (HTC-NH2) provided spongy structures. The adsorption capacity of the samples can be obtained by the Langmuir model, and the adsorption kinetics could be described by the pseudo-second-order model at pH 1.0. The maximum adsorption capacity of HTC-NH2 in the Langmuir model is 74.60 mg/g, much higher than that of HTC (61.25 mg/g). The green hydrothermal treatment of biomass with ammonia solution will provide a simple and feasible way to prepare adsorbent for Cr(VI) in waste water treatment.
| S-EPMC7961731 | biostudies-literature
Project description:Heavy metal ions represent one of the most toxic and environmentally harmful pollutants of water sources. This work reports the development of a novel chelating nitrogen-doped carboxylated porous carbon (ND-CPC) adsorbent for the effective removal of the heavy metal ions Pb(II), Hg(II), and Cr(VI) from contaminated and polluted water sources. The ND-CPC adsorbent is designed to combine four different types of nitrogen functional groups (graphitic, pyrrolic, pyridinic, and pyridine oxide) with the carboxylic acid functional groups within a high surface area of 1135 ± 20 m2/g of the porous carbon structure. The ND-CPC adsorbent shows exceptionally high adsorption affinity for Pb(II) with a capacity of 721 ± 14 mg/g in addition to high uptake values of 257 ± 5 and 104 ± 2 mg/g for Hg(II) and Cr(VI), respectively. The high adsorption capacity is also coupled with fast kinetics where the equilibrium time required for the 100% removal of Pb(II) from 50 ppb and 10 ppm concentrations is 30 s and 60 min, respectively. Even with the very high concentration of 700 ppm, 74% uptake of Pb(II) is achieved within 90 min. Removal efficiencies of 100% of Pb(II), 96% of Hg(II), 91% of Cu(II), 82% of Zn(II), 25% of Cd(II), and 13% of Ni(II) are achieved from a solution containing 10 ppm concentrations of these ions, thus demonstrating excellent selectivity for Pb(II), Hg(II), and Cu(II) ions. Regeneration of the ND-CPC adsorbent shows excellent desorption efficiencies of 99 and 95% for Pb(II) and Cr(VI) ions, respectively. Because of the fast adsorption kinetics, high removal capacity and excellent regeneration, stability, and reusability, the ND-CPC is proposed as a highly efficient remediation adsorbent for the solid-phase removal of Pb(II), Hg(II), and Cr(VI) from contaminated water.
| S-EPMC7774276 | biostudies-literature
Project description:A series of the magnetic CuFe2O4-loaded corncob biochar (CuFe2O4@CCBC) materials was obtained by combining the two-step impregnation of the corncob biochar with the pyrolysis of oxalate. CuFe2O4@CCBC and the pristine corncob biochar (CCBC) were characterized using XRD, SEM, VSM, BET, as well as pHZPC measurements. The results revealed that CuFe2O4 had a face-centered cubic crystalline phase and was homogeneously coated on the surface of CCBC. The as-prepared CuFe2O4@CCBC(5%) demonstrated a specific surface area of 74.98 m2·g-1, saturation magnetization of 5.75 emu·g-1 and pHZPC of 7.0. The adsorption dynamics and thermodynamic behavior of Pb(II) on CuFe2O4@CCBC and CCBC were investigated. The findings indicated that the pseudo-second kinetic and Langmuir equations suitably fitted the Pb(II) adsorption by CuFe2O4@CCBC or CCBC. At 30 °C and pH = 5.0, CuFe2O4@CCBC(5%) displayed an excellent performance in terms of the process rate and adsorption capacity towards Pb(II), for which the theoretical rate constant (k2) and maximum adsorption capacity (qm) were 7.68 × 10-3 g·mg-1··min-1 and 132.10 mg·g-1 separately, which were obviously higher than those of CCBC (4.38 × 10-3 g·mg-1·min-1 and 15.66 mg·g-1). The thermodynamic analyses exhibited that the adsorption reaction of the materials was endothermic and entropy-driven. The XPS and FTIR results revealed that the removal mechanism could be mainly attributed to the replacement of Pb2+ for H+ in Fe/Cu-OH and -COOH to form the inner surface complexes. Overall, the magnetic CuFe2O4-loaded biochar presents a high potential for use as an eco-friendly adsorbent to eliminate the heavy metals from the wastewater streams.
| S-EPMC7435881 | biostudies-literature
Project description:Ethylene vinyl alcohol (EVOH) nanofiber membranes were prepared by melt-blending extrusion with cellulose acetate butyrate ester (CAB) as the matrix and a high-speed flow deposition process. Then, aminated-EVOH (l-Lys/EVOH, Cy/l-Lys/EVOH and DETA/EVOH) nanofiber membranes were prepared for hexavalent chromium [Cr(vi)] removal by facile chemical modification on the surface of EVOH nanofiber membranes. Scanning electron microscopy (SEM), Fourier transform-infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS) were carried out to test the morphology and structure of aminated-EVOH nanofiber membranes. Adsorption experiments suggested that amination was beneficial to adsorption, and the optimal pH for prepared membranes to Cr removal was 2.0. Adsorption kinetics analysis revealed that the adsorption process was successfully fitted with a Pseudo-second-order model. The Freundlich isothermal model well described the adsorption isotherm data. A thermodynamic study suggested that the adsorption process was endothermic and spontaneous. Aminated-EVOH nanofiber membranes exhibited excellent reusability for Cr removal. The Cr adsorption efficiency of DETA/EVOH nanofiber membranes retained up to 98.73% of the initial adsorption after 6 successive adsorption-desorption cycles.
| S-EPMC9076933 | biostudies-literature
Project description:Heavy metals are the major concern of the modern age. Among the heavy metals, chromium (Cr(VI)) is regarded as a highly toxic heavy metal released largely from leather tanning operations. To remove such high concentrations of Cr(VI), an advanced method is required urgently. Thus, biosorption using biochar, which is an organic material produced from various sources such as walnut shell, can be applied successfully for Cr(VI) abatement. The major objectives of this experiment were the remediation of the Cr(VI) heavy metal using walnut shell biochar and checking of the effect of pH, biochar dosage, Cr level, and shaking time. Remediation of Cr(VI) using walnut shell biochar was proved to be effective and removed the maximum concentration of Cr(VI) up to 93% at pH 5.5, 2 h agitation time, and the biochar amount of 1.1 g L-1 from an aqueous solution. Equilibrium modeling demonstrated that the chemisorption process was involved in adsorption of Cr(VI). The surface of the biochar was porous and provided numerous sites for Cr(VI) attachment, which was also confirmed by the presence of Cr(VI) onto the biochar after adsorption. Hence, the use of walnut shell biochar was highly effective as a sorbent, which could conveniently be applied to small-scale as well as large-scale levels.
| S-EPMC8467037 | biostudies-literature