Browse
Submit Data
Databases
API
Help

Dataset Information

27 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Preparation of the WO _X /MCM-41 Solid Acid Catalyst and the Catalytic Performance for Solketal Synthesis.

ABSTRACT: In the present work, an efficient and stable WO _X /MCM-41 solid acid catalyst was prepared by the wet impregnation method. The characterization of powder X-ray diffraction, transmission electron microscopy, ultraviolet-visible, H₂ temperature-programmed reduction, X-ray photoelectron spectroscopy, NH₃ temperature-programmed desorption, and N₂ adsorption-desorption isotherms confirmed that the impregnation amount and calcination temperature of WO _X speciation affected the dispersity and acidity of the resulting catalyst. This WO _X /MCM-41 solid acid catalyst was subsequently applied in the ketalization reaction of glycerol and acetone to produce solketal. By catalyst screening and reaction condition optimization, WO _X /MCM-41 obtained by impregnating 20 wt % and calcining at 350 °C exhibited the highest solketal yield and catalytic stability.

SUBMITTER: Huang Y

PROVIDER: S-EPMC7876846 | biostudies-literature | 2021 Feb

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Publications

Preparation of the WO X /MCM-41 Solid Acid Catalyst and the Catalytic Performance for Solketal Synthesis.

Huang Yixuan Y Zhang Guangcai G Zhang Qinhui Q

ACS omega 20210130 5

In the present work, an efficient and stable WO X /MCM-41 solid acid catalyst was prepared by the wet impregnation method. The characterization of powder X-ray diffraction, transmission electron microscopy, ultraviolet-visible, H2 temperature-programmed reduction, X-ray photoelectron spectroscopy, NH3 temperature-programmed desorption, and N2 adsorption-desorption isotherms confirmed that the impregnation amount and calcination temperature of WO ...[more]

PMID: 33585766

Similar Datasets

Facile Preparation of MCM-41/Ag2O Nanomaterials with High Iodide-Removal Efficiency.

Project description:The elimination of iodide (I-) from water is a tough subject due to its low adsorption tendency and high mobility. In this work, MCM-41/Ag2O nanomaterials were prepared, characterized, and employed to adsorb I- from water. The Ag2O nanoparticles were dispersed homogeneously in the pores or at the surface of the MCM-41 support, and the Ag2O nanoparticles in the pores had small particles sizes due to the confinement of the mesoporous channel. The prepared MCM-41/Ag2O nanomaterials exhibited a higher specific surface area than previously reported Ag2O-based composites. The adsorption of I- by the nanomaterials was able to reach equilibrium at 180 min. The MCM-41/Ag2O nanomaterials showed a better adsorption capacity per unit mass of Ag2O than pure Ag2O nanoparticles and previously reported Ag2O-based composites prepared using other supports. Furthermore, the MCM-41/Ag2O nanomaterials exhibited high selectivity for I- in the presence of high concentrations of competitive anions, such as Cl- or Br-, and could function in a wide range of pH. The chemical reaction between Ag2O and I- and the surface adsorption were the main adsorption mechanisms. These results indicate that MCM-41/Ag2O nanomaterials are a promising and efficient adsorbent material suitable for the removal of I- for practical application.

| S-EPMC9610164 | biostudies-literature

Pd/MCM-41 catalyst for acetylene hydrogenation to ethylene.

Project description:This study aims to produce ethylene using the calcium carbide route, acetylene from calcium carbide and then selective hydrogenation of the high-concentration acetylene to ethylene. A series of catalysts with different supports, such as Al2O3, SiO2 and MCM-41, were prepared using the ethylene glycol reduction method and their catalytic properties for high-concentration acetylene hydrogenation of calcium carbide to ethylene were studied by transmission electron microscopy, X-ray powder diffraction and thermogravimetry, among others. The results show that the small particle size and uniform dispersion of palladium (Pd) particles in the Pd/MCM-41 catalyst produced the highest ethylene yield of 62.09%. Then, the conditions for the basic reaction, such as reaction temperature and space velocity, were optimized using MCM-41 as a support. The yield of ethylene after condition optimization was as high as 82.87%, while the loading of Pd was 0.1%.

| S-EPMC6894548 | biostudies-literature

Study on the preparation and n-heptane isomerization performance of MoOx-Pd/Ce-MCM-48 catalyst.

Project description:A Ce-MCM-48 molecular sieve was prepared by the hydrothermal synthesis method. Using Ce-MCM-48 as the support, a series of MoOx Pd/Ce-M catalysts were prepared by the impregnation method by introducing MoOx and Pd. XRD, N2 adsorption desorption, SEM, TEM, NH3-TPD, Py-IR, FT-IR, and ICP-MS were used to characterize the physicochemical properties. The performance of n-heptane isomerization in a micro fixed bed device was evaluated. The results showed that the synthesized Ce-MCM-48 was mesoporous, with a spherical particle morphology, a long-range ordered pore structure, weakly acidic sites on the surface, and an increase of B and L acids. The 2% MoOx-Pd/Ce-M catalyst was used for the probe reaction of n-heptane hydroisomerization; when the reduction temperature was 400 °C, the reduction time was 2 hours, the reaction temperature was 300 °C, the WHSV was 7.6 h-1, the conversion rate was 58.7%, the selectivity was 91.2%, and the maximum yield was 53.5%. The product distribution of multiple C7 isomers increased the selectivity of multi branched isoheptane. The addition of an appropriate amount of MoOx would improve the performance of n-heptane isomerization.

| S-EPMC10825628 | biostudies-literature

A magnetic-void-porous MnFe2O4/carbon microspheres nano-catalyst for catalytic ozonation: Preparation, performance and mechanism.

Project description:Wastewater treatment is essential to guarantee human health and ecological security. Catalytic ozonation with nanocatalysts is a widely studied and efficient treatment technology. However, this method has always been limited by nanocatalysts disadvantages such as easily loss, difficult to separate and reuse, and catalytic ability decay caused by aggregation, which could cause severe resources waste and potential risk to human health and ecosystem. To remedy these challenges, a magnetic-void-porous MnFe2O4/carbon microsphere shell nanocatalyst (CMS-MnFe2O4) was successfully synthesized using renewable natural microalgae. The separation test showed CMS-MnFe2O4 was rapidly separated within 2 min under an external magnetic field. In catalytic ozonation of oxalic acid (OA), CMS-MnFe2O4 showed efficient and stable catalytic efficiency, reaching a maximum total organic carbon removal efficiency of 96.59 % and maintained a 93.88 % efficiency after 4 cycles. The stable catalytic efficiency was due to the supporting effects of the carbon microsphere shell, which significantly enhanced CMS-MnFe2O4 chemical stability and reduced the metal ions leaching to 10-20 % of MnFe2O4 through electron transfer. To explore the catalytic mechanism, radical experiments were conducted and a new degradation pathway of OA involving superoxide anions rather than hydroxyl radicals was proposed. Consequently, this study suggests that an efficient, recyclable, stable, and durable catalyst for catalytic ozonation could be prepared.

| S-EPMC9488059 | biostudies-literature

Preparation of CuHY catalyst via solid-state ion exchange method and its catalytic performance in isobutane/2-butene alkylation.

Project description:CuHY samples prepared by solid-state ion exchange of HY zeolite with CuCl were used as catalysts in isobutane/2-butene alkylation. The results show that both the addition amount of CuCl and the calcination temperature affect the ion exchange degree. Cu+ can be introduced into Y zeolite by replacing H+ in the HY zeolite after the solid-state ion exchange, causing a decrease of the amount of Brønsted acid sites and an increase of that of Lewis acid sites. When taking CuHY as the catalyst in isobutane/2-butene alkylation, the 3d104s0 valence electron configuration of Cu+ makes it favorable for inhibiting the oligomerization of 2-butene and accelerating the hydride transfer reaction rate by indirectly increasing the local isobutane/olefin ratio around the acid sites of the catalyst. As a result, the selectivity of C8 and trimethylpentanes over CuHY in alkylate are improved compared with those of HY.

| S-EPMC9034412 | biostudies-literature

Catalytic Pyrolysis of Lignocellulosic Biomass: The Influence of the Catalyst Regeneration Sequence on the Composition of Upgraded Pyrolysis Oils over a H-ZSM-5/Al-MCM-41 Catalyst Mixture.

Project description:Catalyst regeneration is economically attractive, and it saves resources. Thus, it is important to determine the influence of catalyst regeneration on the chemical composition of upgraded oil. The catalyst was regenerated several times, and the regenerated catalyst was reloaded in the reactor to proceed with the next run. The composition of the derived upgraded pyrolysis oils in relation to catalyst regeneration was determined. The results revealed that the catalyst cracking abilities decreased with an increased number of reaction cycles. The opposite trends of the organic fraction and water yields indicated that the deoxygenation process occurred via H2O production. A decrease in the CO and CO2 yields revealed that the deoxygenation in catalytic pyrolysis with a catalyst mixture occurred via decarbonylation, decarboxylation, and dehydration mechanisms. The chemical formula of bio-oil changed from CH0.17O0.91 for a noncatalytic experiment to CH0.14O0.66 for a catalytic pyrolysis experiment after five reaction cycles, which indicated that the oxygen in the bio-oil decreased at the expense of hydrogen. The high heating value (HHV) of bio-oils decreased as the number of reaction cycles increased, albeit the minimum value of 22.41 wt % in the 6th reaction cycle was still higher than the value for the noncatalytic experiment. Compared to the HHVs of diesel fuel and gasoline petrol, the values of the produced bio-oil with catalyst mixtures were still low. The catalyst regained 94% of the surface area for the fresh catalyst, which indicated that the regeneration procedure was effective.

| S-EPMC7675534 | biostudies-literature

Effect of Hydrothermal Treatment on Structural and Catalytic Properties of [CTA]-MCM-41 Silica.

Project description:The [CTA]-MCM-41 hybrid silica is a useful and simply prepared heterogeneous basic catalyst for the transesterification reaction. Here, the effect of hydrothermal treatment during catalyst preparation was investigated, with the aim of improving the structural stability of this catalyst during the reaction. It was observed that the hydrothermal step led to the formation of a material with a higher degree of organization and a greater wall thickness, which improved its structural stability. However, the catalyst prepared using this treatment presented lower catalytic activity, due to the presence of fewer active sites.

| S-EPMC5978237 | biostudies-literature

Effect of Additives on CO2 Adsorption of Polyethylene Polyamine-Loaded MCM-41.

Project description:Organic amine-modified mesoporous carriers are considered potential CO2 sorbents, in which the CO2 adsorption performance was limited by the agglomeration and volatility of liquid amines. In this study, four additives of ether compounds were separately coimpregnated with polyethylene polyamine (PEPA) into MCM-41 to prepare the composite chemisorbents for CO2 adsorption. The textural pore properties, surface functional groups and elemental contents of N for MCM-41 before and after functionalization were characterized; the effects of the type and amount of additives, adsorption temperature and influent velocity on CO2 adsorption were investigated; the amine efficiency was calculated; and the adsorption kinetics and regeneration for the optimized sorbent were studied. For 40 wt.% PEPA-loaded MCM-41, the CO2 adsorption capacity and amine efficiency at 60 °C were 1.34 mmol/g and 0.18 mol CO2/mol N, when the influent velocity of the simulated flue gas was 30 mL/min, which reached 1.81 mmol/g and 0.23 mol CO2/mol N after coimpregnating 10 wt.% of 2-propoxyethanol (1E). The maximum adsorption capacity of 2.16 mmol/g appeared when the influent velocity of the simulated flue gas was 20 mL/min. In addition, the additive of 1E improved the regeneration and kinetics of PEPA-loaded MCM-41, and the CO2 adsorption process showed multiple adsorption routes.

| S-EPMC10934004 | biostudies-literature

Synthesis, Characterization, and NH3-SCR Catalytic Performance of Fe-Modified MCM-36 Intercalated with Various Pillars.

Project description:Two series of MCM-36 zeolites intercalated with various pillars and modified with iron were synthesized, analyzed with respect to their physicochemical properties, and tested as catalysts for the NH3-SCR process. It was found that the characteristic MWW morphology of MCM-36 can be obtained successfully using silica, alumina, and iron oxide as pillars. Additionally, one-pot synthesis of the material with iron resulted in the incorporation of monomeric Fe3+ species into the framework positions. The results of catalytic tests revealed that the one-pot synthesized sample intercalated with silica and alumina was the most efficient catalyst of NO reduction, exhibiting ca. 100% activity at 250 °C. The outstanding performance of the material was attributed to the abundance of Lewis acid sites and the beneficial influence of alumina on the distribution of iron species in the zeolite. In contrast, the active centers originating from the Fe2O3 pillars improved the NO conversion in the high-temperature range. Nevertheless, the aggregated particles of the metal oxide limited the access of the reacting molecules to the inner structure of the catalyst, which affected the overall activity and promoted the formation of N2O above 300 °C.

| S-EPMC10343675 | biostudies-literature

Reactive Adsorption Performance and Behavior of Gaseous Cumene on MCM-41 Supported Sulfuric Acid.

Project description:Efficient removal of cumene from gaseous streams and recovery of its derivatives was accomplished using a MCM-41-supported sulfuric acid (SSA/MCM-41) adsorbent. The results indicated that the removal performance of the SSA/MCM-41 for cumene was significantly influenced by the process conditions such as bed temperature, inlet concentration, bed height, and flow rate. The dose-response model could perfectly describe the collected breakthrough adsorption data. The SSA/MCM-41 adsorbent exhibited a reactive temperature region of 120-170 °C, in which the cumene removal ratios (Xc) were greater than 97%. Rising the bed height or reducing the flow rate enhanced the theoretical adsorption performance metrics, such as theoretical breakthrough time (tB,th) and theoretical breakthrough adsorption capacity (QB,th), whereas increasing the inlet concentration resulted in tB,th shortening and QB,th rising. As demonstrated in this paper, the highest tB,th and QB,th were 69.60 min and 324.50 mg g-1, respectively. Meanwhile, the spent SSA/MCM-41 could be desorbed and regenerated for cyclic reuse. Moreover, two recoverable adsorbed products, 4-isopropylbenzenesulfonic acid and 4, 4'-sulfonyl bis(isopropyl-benzene), were successfully separated and identified using FTIR and 1H/13C NMR characterization. Accordingly, the relevance of a reactive adsorption mechanism was confirmed. This study suggests that the SSA/MCM-41 has remarkable potential for application as an adsorbent for the resource treatment of cumene pollutants.

| S-EPMC9416091 | biostudies-literature