Dataset Information

Clindamycin-Based 3D-Printed and Electrospun Coatings for Treatment of Implant-Related Infections.

ABSTRACT: This study presents the development and characterisation of two novel bioactive coatings deposited on TiAlV and AISI 316LVM substrates. The coatings were prepared using 3D printing and electrospinning. The 3D-printed coating consisted of the cellulose nanofibril suspension, alginate, and carboxymethylcellulose (CMC), while CMC and polyethylene oxide were used to prepare the electrospun coating. Both coatings were loaded with the antibiotic clindamycin (CLIN), which is a bacteriostatic lincosamide known for its activity against streptococci, staphylococci, pneumococci, Bacteroides species, and other anaerobes. Initial characterisation of the coatings was performed by attenuated total reflectance Fourier transform infrared spectroscopy, field emission scanning electron microscopy, and atomic force microscopy. Furthermore, the contact angle measurements, swelling rate, and biodegradability of the coatings were investigated. The released concentration of CLIN in PBS (pH = 7.4 at 25 °C) was determined by UV-VIS spectrophotometry. The coatings' biocompatibility was determined using an MTT (3(4,5 dimethylthiazolyl-2)-2,5-diphenyltetrazolium bromide) assay using an osteoblast cell culture (hFOB 1.19, ATCC CRL 11372).

SUBMITTER: Maver T

PROVIDER: S-EPMC8002500 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:Biomaterial-associated infections are one of the major causes of implant failure. These infections result from persistent bacteria that have adhered to the biomaterial surface before, during, or after surgery and have formed a biofilm on the implant's surface. It is estimated that 4 to 10% of implant surfaces are contaminated with bacteria; however, the infection rate can be as high as 30% in intensive care units in developed countries and as high as 45% in developing countries. To date, there is no clinical solution to prevent implant infection without relying on the use of high doses of antibiotics supplied systemically and/or removal of the infected device. In this study, melimine, a chimeric cationic peptide that has been tested in Phase I and II human clinical trials, was immobilized onto the surface of 3D-printed medical-grade polycaprolactone (mPCL) scaffolds via covalent binding and adsorption. X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) spectra of melimine-treated surfaces confirmed immobilization of the peptide, as well as its homogeneous distribution throughout the scaffold surface. Amino acid analysis showed that melimine covalent and noncovalent immobilization resulted in a peptide density of ∼156 and ∼533 ng/cm2, respectively. Furthermore, we demonstrated that the immobilization of melimine on mPCL scaffolds by 1-ethyl-3-[3-(dimethylamino)propyl] carbodiimide hydrochloride (EDC) coupling and noncovalent interactions resulted in a reduction of Staphylococcus aureus colonization by 78.7% and 76.0%, respectively, in comparison with the nonmodified control specimens. Particularly, the modified surfaces maintained their antibacterial properties for 3 days, which resulted in the inhibition of biofilm formation in vitro. This system offers a biomaterial strategy to effectively prevent biofilm-related infections on implant surfaces without relying on the use of prophylactic antibiotic treatment.

Project description:Over the past two decades, electrospinning has emerged as a common technique to produce biomedical scaffolds composed of ultrafine fibers formed from many natural and synthetic polymers. A major advantage of this technique is the ability to produce scaffolds that resemble the native extracellular matrix in physical, chemical, and topological properties. However, scaffolds fabricated via electrospinning are not formed with a controlled architecture and typically do a poor job of directing cell growth into prescribed structures for tissue/organ development. To address these weaknesses, 3D bioprinting has recently been used to develop scaffolds that have a highly organized and precise global topology. Unfortunately, these 3D bioprinted scaffolds do not typically resemble the native extracellular matrix in physical properties, such as porosity, fiber diameter, and pore size (e.g., the microarchitecture). Thus, the goal of the current study was to develop a technique that harnesses the intrinsic advantages of both conventional electrospinning and 3D bioprinting techniques to produce scaffolds that have the potential to be used within biomedical applications. The physical properties of formed 3D printed electrospun scaffolds were compared with conventional electrospun and 3D printed scaffolds. Further, we conducted initial proof-of-concept biocompatibility studies to illustrate the applicability of the scaffolds within vascular applications. Our results illustrate that 3D printed electrospun scaffolds can be developed, via our technique, that have highly tailored and organized arbitrary geometries with scaffold properties in the range of the innate extracellular matrix. In addition, these scaffolds were shown to support endothelial cell growth. Therefore, we illustrate the development and testing of a novel bioscaffold fabrication technique that may be used for many tissue engineering and regenerative medicine applications, which allows for the direct printing of electrospun scaffolds into well-defined macro-scale geometries that also retain the micro-structures commonly observed in electrospun scaffolds.

Dataset Information

Clindamycin-Based 3D-Printed and Electrospun Coatings for Treatment of Implant-Related Infections.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets