Quantification Approaches for Fatigue Crack Resistance of Thermoplastic Tape Layered Composites with Multiple Delaminations.
Ontology highlight
ABSTRACT:
SUBMITTER: Khudiakova A
PROVIDER: S-EPMC8002822 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Flame Retardancy Index, FRI, was defined as a simple yet universal dimensionless criterion born out of cone calorimetry data on thermoplastic composites and then put into practice for quantifying the flame retardancy performance of different polymer composites on a set of reliable data. Four types of thermoplastic composites filled with a wide variety of flame retardant additives were chosen for making comparative evaluations regardless of the type and loading level of the additive as well as the irradiance flux. The main features of cone calorimetry including peak of Heat Release Rate (pHRR), Total Heat Release (THR), and Time-To-Ignition (TTI) served to calculate a dimensionless measure that reflects an improvement in the flame retardancy of nominated thermoplastic composites with respect to the neat thermoplastic, quantitatively. A meaningful trend was observed among well-classified ranges of FRI quantities calculated for the studied dataset on thermoplastic composites by which "Poor", "Good", and "Excellent" flame retardancy performances were explicitly defined and exhibited on logarithmic scales of FRI axis. The proposed index remains adaptable to thermoplastic systems whatever the polymer or additive is.
| S-EPMC6473221 | biostudies-literature
Project description:A fabrication method of a multifunctional hybrid material is achieved by using the insoluble organic nacre matrix of the Haliotis laevigata shell infiltrated with gelatin as a confined reaction environment. Inside this organic scaffold magnetite nanoparticles (MNPs) are synthesized. The amount of MNPs can be controlled through the synthesis protocol therefore mineral loadings starting from 15 wt % up to 65 wt % can be realized. The demineralized organic nacre matrix is characterized by small-angle and very-small-angle neutron scattering (SANS and VSANS) showing an unchanged organic matrix structure after demineralization compared to the original mineralized nacre reference. Light microscopy and confocal laser scanning microscopy studies of stained samples show the presence of insoluble proteins at the chitin surface but not between the chitin layers. Successful and homogeneous gelatin infiltration in between the chitin layers can be shown. The hybrid material is characterized by TEM and shows a layered structure filled with MNPs with a size of around 10 nm. Magnetic analysis of the material demonstrates superparamagnetic behavior as characteristic for the particle size. Simulation studies show the potential of collagen and chitin to act as nucleators, where there is a slight preference of chitin over collagen as a nucleator for magnetite. Colloidal-probe AFM measurements demonstrate that introduction of a ferrogel into the chitin matrix leads to a certain increase in the stiffness of the composite material.
| S-EPMC4311584 | biostudies-literature
Project description:Reinforcement of flexible fibre reinforced plastic (FRP) composites with standard textile fibres is a potential low cost solution to less critical loading applications. The mechanical behaviour of FRPs based on mechanically bonded nonwoven preforms composed of either low or high modulus fibres in a thermoplastic polyurethane (TPU) matrix were compared following compression moulding. Nonwoven preform fibre compositions were selected from lyocell, polyethylene terephthalate (PET), polyamide (PA) as well as para-aramid fibres (polyphenylene terephthalamide; PPTA). Reinforcement with standard fibres manifold improved the tensile modulus and strength of the reinforced composites and the relationship between fibre, fabric and composite's mechanical properties was studied. The linear density of fibres and the punch density, a key process variable used to consolidate the nonwoven preform, were varied to study the influence on resulting FRP mechanical properties. In summary, increasing the strength and degree of consolidation of nonwoven preforms did not translate to an increase in the strength of resulting fibre reinforced TPU-composites. The TPU composite strength was mainly dependent upon constituent fibre stress-strain behaviour and fibre segment orientation distribution.
| S-EPMC5553526 | biostudies-literature
Project description:Fretting fatigue experiments and finite element analysis were carried out to investigate the influence of cylindrical-on-flat contact on crack nucleation, crack path and fatigue life of medium-carbon steel. The location of crack nucleation was predicted using the maximum shear stress range criterion and the maximum relative slip amplitude criterion. The prediction using the maximum relative slip amplitude criterion gave the better agreement with the experimental result, and should be used for the prediction of the location of crack nucleation. Crack openings under compressive bulk stresses were found in the fretting fatigues with flat-on-flat contact and cylindrical-on-flat contacts, i.e., fretting-contact-induced crack openings. The crack opening stress of specimen with flat-on-flat contact was lower than those of specimens with cylindrical-on-flat contacts, while that of specimen with 60-mm radius contact pad was lower than that of specimen with 15-mm radius contact pad. The fretting fatigue lives were estimated by integrating the fatigue crack growth curve from an initial propagating crack length to a critical crack length. The predictions of fretting fatigue life with consideration of crack opening were in good agreement with the experimental results.
| S-EPMC5459140 | biostudies-other
Project description:Thermoplastic composites consisting of a liquid crystalline polymer (LCP) and poly(lactide) (PLA) have the potential to combine good mechanical performance with recyclability and are therefore interesting as strong and sustainable composite materials. The viscoelastic behavior of both the LCP and the PLA is of great importance for the performance of these composites, as they determine the LCP morphology in the composite and play a crucial role in preventing the loss of mechanical performance upon recycling. Though the effect of the matrix viscosity is well-documented in literature, well-controlled systems where the LCP viscosity is tailored are not reported. Therefore, four LCPs, with the same chemical backbone but different molecular weights, are used to produce reinforced LCP-PLA composites. The differences in viscosity of the LCPs and viscosity ratio between the dispersed phase and the matrix of the blends are evident in the resultant composite morphology: in all cases fibrils are formed; however, the diameter increases considerably as the viscosity ratio increases for the higher molar mass LCPs. The fibril diameter ranges from several hundred nanometer to a few micrometer. A typical layered structure in the injection molded composites is observed, where the layer-thickness is influenced by the LCP viscosity. The LCPs are found to effectively reinforce the PLLA matrix, increasing the Young's modulus by 60% and the maximum stress by 40% for the composite containing 30 wt % of the most viscous LCP. Remarkably, this did not result in an increase in brittleness, effectively increasing the toughness of the composite compared to pure PLLA. The feasible reprocessability of this composite is confirmed, by subjecting it to three reprocessing cycles. The relaxation of the LCPs orientation upon heating is measured via in situ WAXD. We compare the relaxation in an amorphous PLA matrix and in a semicrystalline PLLA matrix with that of the pure LCPs. The matrix viscosity is found to strongly influence the relaxation. For example, in a low viscous amorphous matrix relaxation of the LCP fibrils into droplets dominates the process, whereas a semicrystalline matrix helps in maintaining the fibril morphology and intermolecular orientation of the LCP. In the latter case, the LCPs relax via contraction and coalescence of the polydomain texture and maintains a significant degree of orientation until the PLLA crystals melt and the matrix viscosity decreases. The insights gained in this study on the role of the LCP viscosity on the morphology and performance of thermoplastic composites, as well as the relaxation of LCPs in a matrix, will aid progression toward sustainable and reprocessable LCP reinforced thermoplastic composites.
| S-EPMC8290909 | biostudies-literature
Project description:The aim of this study was to investigate the effect of recycling on polypropylene (PP) and wood-fiber thermoplastic composites (WPCs) using a co-rotating twin-screw extruder. After nine extrusion passes microscopy studies confirmed that the fiber length decreased with the increased number of recycling passes but the increased processing time also resulted in excellent dispersion and interfacial adhesion of the wood fibers in the PP matrix. Thermal, rheological, and mechanical properties were studied. The repeated extrusion passes had minimal effect on thermal behavior and the viscosity decreased with an increased number of passes, indicating slight degradation. The recycling processes had an effect on the tensile strength of WPCs while the effect was minor on the PP. However, even after the nine recycling passes the strength of WPC was considerably better (37 MPa) compared to PP (28 MPa). The good degree of property retention after recycling makes this recycling strategy a viable alternative to discarding the materials. Thus, it has been demonstrated that, by following the most commonly used extrusion process, WPCs can be recycled several times and this methodology can be industrially adapted for the manufacturing of recycled products.
| S-EPMC7463641 | biostudies-literature
Project description:Thermoplastic "all-cellulose" composites were synthesized by covalent functionalization of cellulose acetate (CA) with oxidized carbonized cellulose (OCC). The OCC were manufactured via microwave-assisted hydrothermal carbonization (HTC) of cellulose followed by oxidation and dialysis. The OCC were of micrometer-size, had plane morphology and contained a variety of oxygen functionalities, enabling transformation into acyl chlorinated OCC under moderate reaction conditions. The synthesis of OCC-modified CA composites and neat CA were performed in the recyclable ionic liquid 1-allyl-3-methylimidazolium chloride. The degree of acetylation and amount of OCC were varied to establish their influence on thermal and physical properties of the composites. The OCC-modified CA composites displayed a notably enhanced film-forming ability, which led to improved optical and mechanical properties compared to neat CA. In addition, it was shown that OCC-modified CA composites can be synthesized from waste products, such as paper tissues. The OCC-modification was demonstrated to be a promising route to transparent and strong thermoplastic "all-cellulose" composites with moderate flexibility.
| S-EPMC7307885 | biostudies-literature
Project description:In additive manufacturing (AM), thermoplastic components made by fused deposition modeling (FDM) offer low strength and stiffness, as required for fully functional and load-bearing parts. Composite materials are a practical solution to improve mechanical properties [1,2]. A new technology to reinforce thermoplastics with continuous fibers has been developed recently by Markforged [3]. It introduces continuous fiber to reinforce a thermoplastic matrix, thus, taking static mechanical performance close to Aluminum alloys [4]. These printers for continuous fiber reinforced thermoplastic composites (CFRTPC) have taken this technology to a whole new level in terms of mechanical properties and efficient production. Mechanical properties under monotonic load were studied for different kinds of printing configurations. Tensile monotonic tests under controlled displacement were performed until rupture. Raw data showing tensile monotonic behavior provides the researchers with the ability to perform data fitting, to validate more advanced constitutive models, or to perform a further interpretation of the data, among others. Data is presented here as plain text files without any analysis. A preliminary data analysis has been published already in [5]. The text files contain information about time, displacement, and force. The data is useful for design engineers and researchers involved with AM.
| S-EPMC7056620 | biostudies-literature
Project description:The fatigue strength, effects of a notch on the fatigue strength, and fatigue crack growth rate of Ti-15Zr-4Nb-4Ta alloy were compared with those of other implantable metals. Zr, Nb, and Ta are important alloying elements for Ti alloys for attaining superior long-term corrosion resistance and biocompatibility. The highly biocompatible Ti-15Zr-4Nb-4Ta alloy exhibited an excellent balance between strength and ductility. Its notched tensile strength was much higher than that of a smooth specimen. The strength of 20% cold-worked commercially pure (C.P.) grade 4 Ti was close to that of Ti alloy. The tension-to-tension fatigue strength of an annealed Ti-15Zr-4Nb-4Ta rod at 107 cycles was approximately 740 MPa. The fatigue strength of this alloy was much improved by aging treatment after solution treatment. The fatigue strengths of C.P. grade 4 Ti and stainless steel were markedly improved by 20% cold working. The fatigue strength of Co-Cr-Mo alloy was markedly increased by hot forging. The notch fatigue strengths of 20% cold-worked C.P. grade 4 Ti, and annealed and aged Ti-15Zr-4Nb-4Ta, and annealed Ti-6Al-4V alloys were less than those of the smooth specimens. The fatigue crack growth rate of Ti-15Zr-4Nb-4Ta was the same as that of Ti-6Al-4V. The fatigue crack growth rate in 0.9% NaCl was the same as that in air. Stainless steel and Co-Cr-Mo-Ni-Fe alloy had a larger stress-intensity factor range (?K) than Ti alloy.
| S-EPMC5449063 | biostudies-literature
Project description:This article describes a method for fabricating 3D microfluidic devices by stacking layers of patterned paper and double-sided adhesive tape. Paper-based 3D microfluidic devices have capabilities in microfluidics that are difficult to achieve using conventional open-channel microsystems made from glass or polymers. In particular, 3D paper-based devices wick fluids and distribute microliter volumes of samples from single inlet points into arrays of detection zones (with numbers up to thousands). This capability makes it possible to carry out a range of new analytical protocols simply and inexpensively (all on a piece of paper) without external pumps. We demonstrate a prototype 3D device that tests 4 different samples for up to 4 different analytes and displays the results of the assays in a side-by-side configuration for easy comparison. Three-dimensional paper-based microfluidic devices are especially appropriate for use in distributed healthcare in the developing world and in environmental monitoring and water analysis.
| S-EPMC2604941 | biostudies-literature