Browse
Submit Data
Databases
API
Help

Dataset Information

6 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Crack- and Shrinkage-Free Ethylene-Bridged Polysilsesquioxane Film Prepared by a Hydrosilylation Reaction.

ABSTRACT: With the aim of developing an improved strategy for the preparation of ethylene-bridged polysilsesquioxanes as thermal insulator materials, this paper describes the synthesis of a crack- and shrinkage-free ethylene-bridged polysilsesquioxane film by the hydrosilylation reaction of hydrodimethyl-silylated oligomethylsilsesquioxane (MSQ-SiH) and dimethylvinyl-silylated oligomethylsilsesquioxane (MSQ-SiVi) in the presence of Karstedt's catalyst. Polysilsesquioxane precursors were prepared by the sol-gel reaction of triethoxymethylsilane and the successive capping reaction with chlorodimethylsilane and chlorodimethylvinylsilane. The obtained ethylene-bridged polysilsesquioxane film showed lower density and thermal diffusivity (1.13 g/cm³ and 1.15 × 10^-7 m²/s, respectively) than a polymethylsilsesquioxane film (1.34 g/cm³ and 1.36 × 10^-7 m²/s, respectively). As a result of the introduction of the SiCCSi ethylene bridge, the thermal insulation property of the polysilsesquioxane film was enhanced.

SUBMITTER: Hamada T

PROVIDER: S-EPMC8015123 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Ethylene-bridged polysilsesquioxane/hollow silica particle hybrid film for thermal insulation material.

Project description:Ethylene-bridged polysilsesquioxane (EBPSQ) was prepared by the sol-gel reaction of bis(triethoxysilyl)ethane. The whitish slurry was prepared by mixing EBPSQ and hollow silica particles (HSPs) with a median diameter of 18-65 μm at 80 °C, and it formed a hybrid film by heating at 80 and 120 °C for 1 h at each temperature, then at 200 °C for 20 min. The surface temperatures of EBPSQ films containing 10 wt% and 20 wt% of HSPs (90.2 °C-90.5 °C) were lower than those of EBPSQ films (93.6 °C), when the films on the duralumin plate were heated at 100 °C for 10 min from the bottom of the duralumin plate. The thermal conductivity/heat flux (k/q) obtained from the temperature difference between the surface temperature and bottom temperature of the films and the film thickness also decreased with adding the HSPs. EBPSQ film without HSPs exhibited T 5 d of 258 °C and T 10 d of 275 °C. However, EBPSQ film containing 20 wt% of HSPs exhibited high thermal stability, and T 5 d and T 10 d were 299 °C and 315 °C, respectively. Interestingly, T 5 d and T 10 d of the hybrid films increased with an increase in the number of HSPs. Overall, it was shown that HSPs could improve the thermal insulation properties and thermal stability.

| S-EPMC9037016 | biostudies-literature

A Novel Imide-Bridged Polysiloxane Membrane Was Prepared via One-Pot Hydrosilylation Reaction for O<sub>2</sub>/N<sub>2</sub> Separation.

Project description:The synthesis of poly(methyhydrosiloxane) (PMHS) and N,N'-bis(3-allyl)pyromellitic diimide was optimized for O2/N2 separation. The membrane exhibits excellent mechanical and thermal properties and shows an O2/N2 selectivity of up to 4.44 with an O2 permeability of 31.0 Barrer; compared with polydimethylsiloxane (PDMS) and pure polyimide (PI) membranes, the separation selectivity shows a 107% increase for PDMS, and the permeation shows a 660% increase for pure PI. The obtained results were well above the ones reported on the literature for similar conditions opening the door for the preparation of a stable polysiloxane (PMHS-I) gas separation membrane with extraordinary O2/N2 separation performance.

| S-EPMC8340101 | biostudies-literature

Mechanisms of Competitive Adsorption Organic Pollutants on Hexylene-Bridged Polysilsesquioxane.

Project description:Hexylene-bridged periodic mesoporous polysilsesquioxanes (HBPMS) are a promising new class of adsorbent for the removal of organic contaminants from aqueous solutions. These hybrid organic-inorganic materials have a larger BET surface area of 897 m2·g-1 accessible through a cubic, isotropic network of 3.82-nm diameter pores. The hexylene bridging group provides enhanced adsorption of organic molecules while the bridged polysilsesquioxane structure permits sufficient silanols that are hydrophilic to be retained. In this study, adsorption of phenanthrene (PHEN), 2,4-Dichlorophenol (DCP), and nitrobenzene (NBZ) with HBPMS materials was studied to ascertain the relative contributions to adsorption performance from (1) direct competition for sites and (2) pore blockage. A conceptual model was proposed to further explain the phenomena. This study suggests a promising application of cubic mesoporous BPS in wastewater treatment.

| S-EPMC5512655 | biostudies-other

Precise Controlled Target Molecule Release through Light-Triggered Charge Reversal Bridged Polysilsesquioxane Nanoparticles.

Project description:Precise control of target molecule release time, site, and dosage remains a challenge in controlled release systems. We employed a photoresponsive molecule release system via light-triggered charge reversal nanoparticles to achieve a triggered, stepwise, and precise controlled release platform. This release system was based on photocleavage-bridged polysilsesquioxane nanoparticles which acted as nanocarriers of doxorubicin loaded on the surface via electrostatic interaction. The nanoparticles could reverse into positive charges triggered by 254 nm light irradiation due to the photocleavage of the o-nitrobenzyl bridged segment. The charge reversal property of the nanoparticles could release loaded molecules. Doxorubicin was selected as a positively charged model molecule. The as-prepared nanoparticles with an average size of 124 nm had an acceptable doxorubicin loading content up to 12.8%. The surface charge of the nanoparticles could rapidly reverse from negative (-28.20 mV) to positive (+18.9 mV) upon light irradiation for only 10 min. In vitro release experiments showed a cumulative release up to 96% with continuously enhancing irradiation intensity. By regulating irradiation parameters, precisely controlled drug release was carried out. The typical "stepped" profile could be accurately controlled in an on/off irradiation mode. This approach provides an ideal light-triggered molecule release system for location, timing, and dosage. This updated controlled release system, triggered by near-infrared or infrared light, will have greater potential applications in biomedical technology.

| S-EPMC8346980 | biostudies-literature

Influence of alkalinity on the synthesis of hierarchical LTA zeolite by using bridged polysilsesquioxane.

Project description:The mechanism of formation of hierarchical LTA zeolite involved the methoxyl groups of bridged polysilsesquioxane hydrolyzing into hydroxyl groups. The covalent Si-O-Si bond between silicon hydroxyl in the above solution and other silica sources forms by dehydration, avoiding phase separation. The influence of alkalinity on the synthesis of hierarchical LTA zeolites was investigated by using bridged polysilsesquioxane. XRD patterns indicate the synthesis of sodalite at the same molar composition of the hierarchical LTA zeolites without bridged polysilsesquioxane. The characterization results from TG and DTG revealed that bridged polysilsesquioxane was successfully incorporated into the as-synthesized hierarchical LTA zeolite. N2-adsorption/desorption results proved that mesopores and the porosities of the hierarchical LTA zeolites are adjustable by a change of alkalinity. SEM images indicated that the morphologies of the hierarchical LTA zeolites changed with increasing alkalinity. The hierarchical LTA zeolites showed faster initial exchange rates of Na+ to Mg2+ compared with conventional LTA.

| S-EPMC9059882 | biostudies-literature

The effect of differential mineral shrinkage on crack formation and network geometry.

Project description:Rock, concrete, and other engineered materials are often composed of several minerals that change volumetrically in response to variations in the moisture content of the local environment. Such differential shrinkage is caused by varying shrinkage rates between mineral compositions during dehydration. Using both 3D X-ray imaging of geo-architected samples and peridynamic (PD) numerical simulations, we show that the spatial distribution of the clay affects the crack network geometry with distributed clay particles yielding the most complex crack networks and percent damage (99.56%), along with a 60% reduction in material strength. We also demonstrate that crack formation, growth, coalescence, and distribution during dehydration, are controlled by the differential shrinkage rates between a highly shrinkable clay and a homogeneous mortar matrix. Sensitivity tests performed with the PD models show a clay shrinkage parameter of 0.4 yields considerable damage, and reductions in the parameter can result in a significant reduction in fracturing and an increase in material strength. Additionally, isolated clay inclusions induced localized fracturing predominantly due to debonding between the clay and matrix. These insights indicate differential shrinkage is a source of potential failure in natural and engineered barriers used to sequester anthropogenic waste.

| S-EPMC9789088 | biostudies-literature

Straining graphene using thin film shrinkage methods.

Project description:Theoretical works suggest the possibility and usefulness of strain engineering of graphene by predicting remarkable properties, such as Dirac cone merging, bandgap opening and pseudo magnetic field generation. However, most of these predictions have not yet been confirmed because it is experimentally difficult to control the magnitude and type (e.g., uniaxial, biaxial, and so forth) of strain in graphene devices. Here we report two novel methods to apply strain without bending the substrate. We employ thin films of evaporated metal and organic insulator deposited on graphene, which shrink after electron beam irradiation or heat application. These methods make it possible to apply both biaxial strain and in-plane isotropic compressive strain in a well-controlled manner. Raman spectroscopy measurements show a clear splitting of the degenerate states of the G-band in the case of biaxial strain, and G-band blue shift without splitting in the case of in-plane isotropic compressive strain. In the case of biaxial strain application, we find out the ratio of the strain component perpendicular to the stretching direction is at least three times larger than what was previously observed, indicating that shrinkage of the metal or organic insulator deposited on graphene induces both tensile and compressive strain in this atomically thin material. Our studies present for the first time a viable way to apply strain to graphene without the need to bend the substrate.

| S-EPMC3962252 | biostudies-other

Poly (3, 4-ethylene dioxythiophene) Supported Palladium Catalyst prepared by Galvanic Replacement Reaction for Methanol Tolerant Oxygen Reduction.

Project description:Herein, we propose a facile electrochemical approach for the synthesis of Pd loaded poly 3, 4-ethylenedioxythiophene (PEDOT) electrodeposited on glassy carbon electrode (GCE) resulting in high surface area. The catalyst preparation is initiated with EDOT polymerization on GCE surface by electrochemical potential cycling method, followed by the electrodeposition of Cu from a 2?mM solution of CuSO4 in 0.1?M NaClO4 at a constant potential of +0.34?V vs. SHE in the form of Cu nanocubes on the PEDOT surface. Pd-PEDOT catalyst was then prepared by the partial substitution of copper by galvanic displacement with various concentrations of PdCl2. The prepared Pd/PEDOT electrocatalyst is found to be methanol resistant indicating its usefulness as fuel cell cathode. The prepared catalyst supports two electron transfer of oxygen reduction reaction in 0.5?M H2SO4. The effects of Pd and Cu contents and the quantity of PEDOT, mass and specific activities were studied. At a relatively low Pd loading of 0.57?ng/cm2, the Pd/PEDOT should be a cost-effective alternative cathode catalyst for direct methanol fuel cells, DMFCs. This work explains the usefulness of PEDOT as good catalyst supporting material which is prepared by an eco-friendly electrochemical route.

| S-EPMC6915768 | biostudies-literature

Polyhydroxyurethane and Poly(ethylene oxide) Multiblock Copolymer Networks: Crosslinking with Polysilsesquioxane, Reprocessing and Solid Polyelectrolyte Properties.

Project description:This contribution reports the synthesis of polyhydroxyurethane (PHU)-poly(ethylene oxide) (PEO) multiblock copolymer networks crosslinked with polysilsesquioxane (PSSQ). First, the linear PHU-PEO multiblock copolymers were synthesized via the step-growth polymerization of bis(6-membered cyclic carbonate) (B6CC) with α,ω-diamino-terminated PEOs with variable molecular weights. Thereafter, the PHU-PEO copolymers were allowed to react with 3-isocyanatopropyltriethoxysilane (IPTS) to afford the derivatives bearing triethoxysilane moieties, the hydrolysis and condensation of which afforded the PHU-PEO networks crosslinked with PSSQ. It was found that the PHU-PEO networks displayed excellent reprocessing properties in the presence of trifluoromethanesulfonate [Zn(OTf)2]. Compared to the PHU networks crosslinked via the reaction of difunctional cyclic carbonate with multifunctional amines, the organic-inorganic PHU networks displayed the decreased reprocessing temperature. The metathesis of silyl ether bonds is responsible for the improved reprocessing behavior. By adding lithium trifluoromethanesulfonate (LiOTf), the PHU-PEO networks were further transformed into the solid polymer electrolytes. It was found that the crystallization of PEO chains in the crosslinked networks was significantly suppressed. The solid polymer electrolytes had the ionic conductivity as high as 7.64 × 10-5 S × cm-1 at 300 K. More importantly, the solid polymer electrolytes were recyclable; the reprocessing did not affect the ionic conductivity.

| S-EPMC10747941 | biostudies-literature

Crack initiation and propagation in sweet cherry skin: A simple chain reaction causes the crack to 'run'.

Project description:Rain cracking severely affects the commercial production of many fleshy-fruit species, including of sweet cherries. The objectives were to investigate how the gaping macroscopic cracks (macrocracks) of a rain-cracked fruit can develop from microscopic cracks in the cuticle (microcracks). Incubating fruit in deionized water is well known to cause significant macrocracking. We found that after a lag phase of 2 h, the numbers and lengths of macrocracks increased. Macrocrack number approached an asymptote at 12 h, whereas macrocrack length continued to increase. The rate of macrocrack propagation (extension at the crack tip) was initially 10.8 mm h-1 but then decreased to a near-constant 0.5 mm h-1. Light microscopy revealed three characteristic zones along a developing macrocrack. In zone I (ahead of the crack), the cuticle was intact, the epidermal cells were unbroken and their cell walls were thin. In zone II, the cuticle was fractured, the first epidermal cells died and their cell walls began to thicken (swell). In zone III, most epidermal cells had died, their cell walls were swollen and cell:cell separation began along the middle lamellae. The thickness of the anticlinal epidermal cell walls and the percentage of intact living cells along a crack were closely and negatively related. Cracks were stained by calcofluor white, but there was no binding of monoclonal antibodies (mAbs) specific for hemicelluloses (LM11, LM21, LM25). Strong binding was obtained with the anti-homogalacturonan mAb (LM19), indicating the presence of unesterified homogalacturonans on the crack surface. We conclude that macrocrack propagation is related to cell death and to cell wall swelling. Cell wall swelling weakens the cell:cell adhesion between neighbouring epidermal cells, which separate along their middle lamellae. The skin macrocrack propagates like a 'run' in a fine, knitted fabric.

| S-EPMC6668808 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data