Synthesis of Co-Fe 1D Nanocone Array Electrodes Using Aluminum Oxide Template.
Ontology highlight
ABSTRACT:
SUBMITTER: Skibinska K
PROVIDER: S-EPMC8036432 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:We have employed anodic aluminum oxide as a template to prepare ultrathin, transparent, and conducting Al films with a unique nanomesh structure for transparent conductive electrodes. The anodic aluminum oxide template is obtained through direct anodization of a sputtered Al layer on a glass substrate, and subsequent wet etching creates the nanomesh metallic film. The optical and conductive properties are greatly influenced by experimental conditions. By tuning the anodizing time, transparent electrodes with appropriate optical transmittance and sheet resistance have been obtained. The results demonstrate that our proposed strategy can serve as a potential method to fabricate low-cost TCEs to replace conventional indium tin oxide materials.
| S-EPMC4735723 | biostudies-other
Project description:Non-close-packed (NCP) silica nanoparticle monolayer arrays (SNMA) on ordered porous anodic aluminum oxide (AAO) templates were fabricated for the first time by a novel two-step spin-coating technique. The obtained NCP-SNMA-AAO was composed of silica nanoparticles (average primary particle size of 440 nm) and well-organized nanopores on the AAO substrates. NCP-SNMA-AAO with a supporting ratio of 87% silica nanoparticles showed a hydrophilic surface (water contact angle of 51.0°), while the original AAO substrate shows a hydrophobic surface (water contact angle of 107.9°). The maximum coefficient of static friction was decreased by 29% (0.327 → 0.233). The coefficient of dynamic friction was also decreased by 20% (0.281 → 0.226). We found that controlling the silica supporting ratio using the two-step spin-coating technique is an effective approach for surface modification of an AAO substrate.
| S-EPMC6733172 | biostudies-literature
Project description:Here we reported a coordinating etching and precipitating method to synthesize a complex binary metal oxides hollow cubic structure. A novel NiCoO2/rGO composite with a structure of NiCoO2 nanocages anchored on layers of reduced graphene oxide (rGO) were synthesized via a simple template-assisted method and the electrochemical performance was investigated by cyclic voltammetry, galvanostatic charge-discharge and electrochemical impedance spectroscopy tests as a faradaic electrode for supercapacitors at a graphene weight ratio of 1 wt% (1%). When used as electrode materials for electrochemical capacitors, the NiCoO2/rGO composites achieved a specific capacity of 1375 F g-1 at the current density of 1 A g-1 and maintained 742 F g-1 at 10 A g-1. After 3000 cycles, the supercapacitor based on these nanocage structures shows long-term cycling performance with a high capacity of 778 F g-1 at a current density of 1 A g-1. These outstanding electrochemical performances are primarily attributed to the special morphological structure and the combination of mixed transition metal oxides and rGO, which not only maintains a high electrical conductivity for the overall electrode but also prevents the aggregation and volume expansion of electrochemical materials during the cycling processes.
| S-EPMC9080341 | biostudies-literature
Project description:Herein, we report a novel method for the formation of hollow Prussian blue analogue (CoFe-PBA) nanocubes, using spherical silica particles as sacrificial templates. In the first step, silica cores are coated by a CoFe-PBA shell and then removed by etching with hydrofluoric acid (HF). The cubic shape of CoFe-PBA is well-retained even after the removal of the silica cores, resulting in the formation of hollow CoFe-PBA cubes. The specific capacity of the hollow CoFe-PBA nanocubes electrodes is about two times higher than that of solid CoFe-PBA nanocubes as storage materials for sodium ions. Such an improvement in the electrochemical properties can be attributed to their hollow internal nanostructure. The hollow architecture can offer a larger interfacial area between the electrolyte and the electrode, leading to an improvement in the electrochemical activity. This strategy can be applied to develop PBAs with hollow interiors for a wide range of applications.
| S-EPMC6080567 | biostudies-literature
Project description:The nanocone-shaped carbon nanotubes field-emitter array (NCNA) is a near-ideal field-emitter array that combines the advantages of geometry and material. In contrast to previous methods of field-emitter array, laser ablation is a low-cost and clean method that does not require any photolithography or wet chemistry. However, nanocone shapes are hard to achieve through laser ablation due to the micrometer-scale focusing spot. Here, we develop an ultraviolet (UV) laser beam patterning technique that is capable of reliably realizing NCNA with a cone-tip radius of ≈300 nm, utilizing optimized beam focusing and unique carbon nanotube-light interaction properties. The patterned array provided smaller turn-on fields (reduced from 2.6 to 1.6 V/μm) in emitters and supported a higher (increased from 10 to 140 mA/cm2) and more stable emission than their unpatterned counterparts. The present technique may be widely applied in the fabrication of high-performance CNTs field-emitter arrays.
| S-EPMC8707308 | biostudies-literature
Project description:Decoupling energy supply from fossil fuels through electrification and sustainable energy management requires efficient and environmentally low-impact energy storage technologies. Potential candidates are charge storage electrodes that combine nickel and cobalt hydroxides with reduced graphene oxide (rGO) designed to achieve high-energy, high-power density and long cycling lifetimes. An early eco-efficiency analysis of these electrodes seeks to examine the impacts of materials and processes used in the synthesis, specifically while focusing on the use of rGO. The emerging electrodes synthesized by means of electrodeposition, are further compared with electrodes obtained by an alternative synthesis route involving co-precipitation. Life cycle assessment (LCA) method was applied to compare a baseline nickel-cobalt hydroxide electrode (NCED), the focal electrode integrating rGO (NCED-rGO), and the benchmark co-precipitated electrode (NCCP), for delivering the charge of 1000 mA h. Contribution analysis reveals that the main environmental hotspots in the synthesis of the NCED-rGO are the use of electricity for potentiostat, ethanol for cleaning, and rGO. Results of comparison show significantly better performance of NCED-rGO in comparison to NCED across all impact categories, suggesting that improved functionalities by addition of rGO outweigh added impacts of the use of material itself. NCED-rGO is more impactful than NCCP except for the indicators of cumulative energy demand, climate change, and fossil depletion. To produce a functional equivalent for the three electrodes, total cumulative energy use was estimated to be 78 W h for NCED, 25 W h for NCED-rGO, and 35 W h for NCCP. Sensitivity analysis explores the significance of rGO efficiency uptake on the relative comparison with NCCP, and potential impact of rGO on the category of freshwater ecotoxicity given absence of removal from the process effluent. Scenario analysis further shows relative performance of the electrodes at the range of alternative functional parameters of current density and lifetime. Lastly, the environmental performance of NCED-rGO electrodes is discussed in regard to technology readiness level and opportunities for design improvements.
| S-EPMC9065049 | biostudies-literature
Project description:In the present work, the approaches of submerged co-cultivation and microparticle-enhanced cultivation (MPEC) were combined and evaluated over the course of three case studies. The filamentous fungus Aspergillus terreus was co-cultivated with Penicillium rubens, Streptomyces rimosus, or Cerrena unicolor in shake flasks with or without the addition of aluminum oxide microparticles. The influence of microparticles on the production of lovastatin, penicillin G, oxytetracycline, and laccase in co-cultures was compared with the effects recorded for the corresponding monocultures. In addition, the quantitative analyses of morphological parameters, sugars consumption, and by-products formation were performed. The study demonstrated that the influence of microparticles on the production of a given molecule in mono- and co-culture may differ considerably, e.g., the biosynthesis of oxytetracycline was shown to be inhibited due to the presence of aluminum oxide in "A. terreus vs. S. rimosus" co-cultivation variants but not in S. rimosus monocultures. The differences were also observed regarding the morphological characteristics, e.g., the microparticles-induced changes of projected area in the co-cultures and the corresponding monocultures were not always comparable. In addition, the study showed the importance of medium composition on the outcomes of MPEC, as exemplified by lovastatin production in A. terreus monocultures. Finally, the co-cultures of A. terreus with a white-rot fungus C. unicolor were described here for the first time. KEY POINTS: • Aluminum oxide affects secondary metabolites production in submerged co-cultures. • Mono- and co-cultures are differently impacted by the addition of aluminum oxide. • Effect of aluminum oxide on metabolites production depends on medium composition.
| S-EPMC9418094 | biostudies-literature
Project description:Among new flexible transparent conductive electrode (TCE) candidates, ultrathin Ag film (UTAF) is attractive for its extremely low resistance and relatively high transparency. However, the performances of UTAF based TCEs critically depend on the threshold thickness for growth of continuous Ag films and the film morphologies. Here, we demonstrate that these two parameters could be strongly altered through the modulation of substrate surface energy. By minimizing the surface energy difference between the Ag film and substrate, a 9 nm UTAF with a sheet resistance down to 6.9 Ω sq-1 can be obtained using an electron-beam evaporation process. The resultant UTAF is completely continuous and exhibits smoother morphologies and smaller optical absorbances in comparison to the counterpart of granular-type Ag film at the same thickness without surface modulation. Template-stripping procedure is further developed to transfer the UTAFs to flexible polymer matrixes and construct Al2O3/Ag/MoOx (AAM) electrodes with excellent surface morphology as well as optical and electronic characteristics, including a root-mean-square roughness below 0.21 nm, a transparency up to 93.85% at 550 nm and a sheet resistance as low as 7.39 Ω sq-1. These AAM based electrodes also show superiority in mechanical robustness, thermal oxidation stability and shape memory property.
| S-EPMC5349598 | biostudies-literature
Project description:MOF-derived carbon (MDC) and metal oxide (MDMO) are superior materials for supercapacitor electrodes due to their high specific capacitances, which can be attributed to their high porosity, specific surface area (SSA), and pore volume. To improve the electrochemical performance, the environmentally friendly and industrially producible MIL-100 (Fe) was prepared using three different Fe sources through hydrothermal synthesis. MDC-A with micro- and mesopores and MDC-B with micropores were synthesized through carbonization and an HCl washing process, and MDMO (α-Fe2O3) was obtained by a simple sintering in air. The electrochemical properties in a three-electrode system using a 6 M KOH electrolyte were investigated. These novel MDC and MDMO were applied to an asymmetric supercapacitor (ASC) system to overcome the disadvantages of traditional supercapacitors, enhancing energy density, power density, and cyclic performance. High SSA materials (MDC-A nitrate and MDMO iron) were selected for negative and positive electrode material to fabricate ASC with KOH/PVP gel electrolyte. As-fabricated ASC resulted in high specific capacitance 127.4 Fg-1 at 0.1 Ag-1 and 48.0 Fg-1 at 3 Ag-1, respectively, and delivered superior energy density (25.5 Wh/kg) at a power density 60 W/kg. The charging/discharging cycling test was also conducted, indicating 90.1% stability after 5000 cycles. These results indicate that ASC with MDC and MDMO derived from MIL-100 (Fe) has promising potential in high-performance energy storage devices.
| S-EPMC10301871 | biostudies-literature
Project description:Oxide ceramic materials underpin a wide variety of technologies. However, the inherent fragility of these materials limits their use in emerging fields like wearable electronics and soft energy storage devices. Here, we develop a sol-gel electrospinning technique followed by calcination to create a range of oxide ceramic nanofiber films that exhibit significant softness without fragility after various deformations. This approach causes the ceramic crystals to fuse together at a low temperature during their growth within the polymer nanofiber templates. All the synthesized ceramic films, from SiO2 to BaTiO3, Li0.33La0.56TiO3, and Li7La3Zr2O12, have silk-like softness of <31 mN, low density of <0.36 g/cm3 and robust fire resistance to 1,000°C. Fabricated separators based on these films display large electrolyte uptakes of >900% and high thermal insulation performance, enhancing the rate capability and safety of lithium batteries. The reported method allows scalable synthesis of soft oxide ceramic films with properties appealing for applications.
| S-EPMC6514271 | biostudies-literature