Towards a neutron and X-ray reflectometry environment for the study of solid-liquid interfaces under shear.
Ontology highlight
ABSTRACT:
SUBMITTER: Armstrong AJ
PROVIDER: S-EPMC8102579 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:refnx is a model-based neutron and X-ray reflectometry data analysis package written in Python. It is cross platform and has been tested on Linux, macOS and Windows. Its graphical user interface is browser based, through a Jupyter notebook. Model construction is modular, being composed from a series of components that each describe a subset of the interface, parameterized in terms of physically relevant parameters (volume fraction of a polymer, lipid area per molecule etc.). The model and data are used to create an objective, which is used to calculate the residuals, log-likelihood and log-prior probabilities of the system. Objectives are combined to perform co-refinement of multiple data sets and mixed-area models. Prior knowledge of parameter values is encoded as probability distribution functions or bounds on all parameters in the system. Additional prior probability terms can be defined for sets of components, over and above those available from the parameters alone. Algebraic parameter constraints are available. The software offers a choice of fitting approaches, including least-squares (global and gradient-based optimizers) and a Bayesian approach using a Markov-chain Monte Carlo algorithm to investigate the posterior distribution of the model parameters. The Bayesian approach is useful for examining parameter covariances, model selection and variability in the resulting scattering length density profiles. The package is designed to facilitate reproducible research; its use in Jupyter notebooks, and subsequent distribution of those notebooks as supporting information, permits straightforward reproduction of analyses.
| S-EPMC6362611 | biostudies-literature
Project description:An approach for optimal experimental design of neutron reflectivity experiments using metrics derived from the Fisher information is presented. This is demonstrated on a range of systems including lipid bilayers and magnetic heterostructures, and it is shown that small (or large) changes to the experimental setup can result in drastically reduced experimental count times. Using the Fisher information (FI), the design of neutron reflectometry experiments can be optimized, leading to greater confidence in parameters of interest and better use of experimental time [Durant, Wilkins, Butler & Cooper (2021). J. Appl. Cryst.54, 1100–1110]. In this work, the FI is utilized in optimizing the design of a wide range of reflectometry experiments. Two lipid bilayer systems are investigated to determine the optimal choice of measurement angles and liquid contrasts, in addition to the ratio of the total counting time that should be spent measuring each condition. The reduction in parameter uncertainties with the addition of underlayers to these systems is then quantified, using the FI, and validated through the use of experiment simulation and Bayesian sampling methods. For a ‘one-shot’ measurement of a degrading lipid monolayer, it is shown that the common practice of measuring null-reflecting water is indeed optimal, but that the optimal measurement angle is dependent on the deuteration state of the monolayer. Finally, the framework is used to demonstrate the feasibility of measuring magnetic signals as small as 0.01 μB per atom in layers only 20 Å thick, given the appropriate experimental design, and that the time to reach a given level of confidence in the small magnetic moment is quantifiable.
| S-EPMC9348865 | biostudies-literature
Project description:Tungsten, a non-Li-intercalating material, was used as a platform to study solid-electrolyte interface/interphase (SEI) formation in lithium hexafluorphosphate in mixed diethyl carbonate (DEC)/ethylene carbonate electrolyte solutions using in situ neutron reflectometry (NR). A NR measurement determines the neutron scattering length density (SLD)-depth profile, from which a composition-depth profile can be inferred. Isotopic labeling/contrast variation measurements were conducted using a series of three electrolyte solutions: one with both solvents deuterated, one with neither deuterated, and another with only DEC deuterated. A two-layer SEI formed upon polarization to +0.25 V vs Li/Li+. Insensitivity of the inner SEI layer to solvent deuteration suggested limited incorporation of hydrogen atoms from the solvent molecules. Its low SLD indicates that Li2O could be a major constituent. The outer SEI layer SLD scaled with that of the solution, indicating that it either had solution-filled porosity, incorporated hydrogen atoms from the solvent, or both. Returning the electrode to +2.65 V removed lithium from both surface layers, though the effect was more pronounced for the inner layer. Potential cycling had the effect of increasing the solution-derived species content in the inner SEI and decreased the contrast between the inner and outer layers, possibly indicating intermixing of the layers.
| S-EPMC7470620 | biostudies-literature
Project description:In solid-liquid systems, macroscopic solids lose their equilibrium and melt in a manner that results in overall movement of the solid-liquid interface. This phenomenon occurs when they are subjected to temperature gradients or external stress, for example. However, many experiments suggest that the melting of nano- and micro-sized metallic nuclei follows a different process not described by traditional melting theory. In this paper, we demonstrate through simulation that the melting of solid nuclei of these sizes occurs via random breaches at the interfaces. Moreover, this breaching process occurs at the exact solid-liquid equilibrium temperature and in the absence of any external disturbance, which suggests the name "self-instability" for this melting process. We attribute this spontaneous instability to the curvature of the samples; based on the relationship between the sample's instability and its curvature, we propose a destabilizing model for small systems. This model fits well with experimental results and leads to new insights into the instability behavior of small-sized systems; these insights have broad implications for research topics ranging from dendrite self-fragmentation to nanoparticle instability.
| S-EPMC4685266 | biostudies-literature
Project description:In this work we investigate the interplay between flow and boundary condition effects on the orientation field of a thermotropic nematic liquid crystal under flow and confinement in a microfluidic device. Two types of experiments were performed using synchrotron small-angle X-ray-scattering (SAXS). In the first, a nematic liquid crystal flows through a square-channel cross section at varying flow rates, while the nematic director orientation projected onto the velocity/velocity gradient plane is measured using a 2D detector. At moderate-to-high flow rates, the nematic director is predominantly aligned in the flow direction, but with a small tilt angle of ∼±11° in the velocity gradient direction. The director tilt angle is constant throughout most of the channel width but switches sign when crossing the center of the channel, in agreement with the Ericksen-Leslie-Parodi (ELP) theory. At low flow rates, boundary conditions begin to dominate, and a flow profile resembling the escaped radial director configuration is observed, where the director is seen to vary more smoothly from the edges (with homeotropic alignment) to the center of the channel. In the second experiment, hydrodynamic focusing is employed to confine the nematic phase into a sheet of liquid sandwiched between two layers of Triton X-100 aqueous solutions. The average nematic director orientation shifts to some extent from the flow direction toward the liquid boundaries, although it remains unclear if one tilt angle is dominant through most of the nematic sheet (with abrupt jumps near the boundaries) or if the tilt angle varies smoothly between two extreme values (∼90 and 0°). The technique presented here could be applied to perform high-throughput measurements for assessing the influence of different surfactants on the orientation of nematic phases and may lead to further improvements in areas such as boundary lubrication and clarifying the nature of defect structures in LC displays.
| S-EPMC4400036 | biostudies-literature
Project description:Slip length describes the classical no-slip boundary condition violation of Newtonian fluid mechanics, where fluids glide on the solid surfaces. Here, we propose a new analytical model validated by experiments for characterization of the liquid slip using vibrating solid surfaces. Essentially, we use a microfluidic system integrated with quartz crystal microbalance (QCM) to investigate the relationship between the slip and the mechanical response of a vibrating solid for a moving fluid. We discover a liquid slip that emerges especially at high flow rates, which is independent of the surface wetting condition, having significant contributions to the changes in resonant frequency of the vibrating solid and energy dissipation on its surface. Overall, our work will lead to consideration of 'missing slip' in the vibrating solid-liquid systems such as the QCM-based biosensing where traditionally frequency changes are interpreted exclusively with mass change on the sensor surface, irrespective of the flow conditions.
| S-EPMC9633805 | biostudies-literature
Project description:Neutron reflectometry (NR) is a powerful tool for providing insight into the evolution of interfacial structures, for example via operando measurements for electrode-electrolyte interfaces, with a spatial resolution of nanometres. The time resolution of NR, which ranges from seconds to minutes depending on the reflection intensity, unfortunately remains low, particularly for small samples made of state-of-the-art materials even with the latest neutron reflectometers. To overcome this problem, a large-area focusing supermirror manufactured with ultra-precision machining has been employed to enhance the neutron flux at the sample, and a gain of approximately 100% in the neutron flux was achieved. Using this mirror, a reflectivity measurement was performed on a thin cathode film on an SrTiO3 substrate in contact with an electrolyte with a small area of 15 × 15 mm. The reflectivity data obtained with the focusing mirror were consistent with those without the mirror, but the acquisition time was shortened to half that of the original, which is an important milestone for rapid measurements with a limited reciprocal space. Furthermore, a method for further upgrades that will reveal the structural evolution with a wide reciprocal space is proposed, by applying this mirror for multi-incident-angle neutron reflectometry.
| S-EPMC7710489 | biostudies-literature
Project description:The growth behavior of intermetallic compounds (IMCs) at the liquid-solid interfaces in Cu/Sn/Cu interconnects during reflow at 250 °C and 280 °C on a hot plate was investigated. Being different from the symmetrical growth during isothermal aging, the interfacial IMCs showed clearly asymmetrical growth during reflow, i.e., the growth of Cu6Sn5 IMC at the cold end was significantly enhanced while that of Cu3Sn IMC was hindered especially at the hot end. It was found that the temperature gradient had caused the mass migration of Cu atoms from the hot end toward the cold end, resulting in sufficient Cu atomic flux for interfacial reaction at the cold end while inadequate Cu atomic flux at the hot end. The growth mechanism was considered as reaction/thermomigration-controlled at the cold end and grain boundary diffusion/thermomigration-controlled at the hot end. A growth model was established to explain the growth kinetics of the Cu6Sn5 IMC at both cold and hot ends. The molar heat of transport of Cu atoms in molten Sn was calculated as + 11.12 kJ/mol at 250 °C and + 14.65 kJ/mol at 280 °C. The corresponding driving force of thermomigration in molten Sn was estimated as 4.82 × 10(-19) N and 6.80 × 10(-19) N.
| S-EPMC4550914 | biostudies-other
Project description:The effects that solid-liquid interfaces exert on the aggregation of proteins and peptides are of high relevance for various fields of basic and applied research, ranging from molecular biology and biomedicine to nanotechnology. While the influence of surface chemistry has received a lot of attention in this context, the role of surface topography has mostly been neglected so far. In this work, therefore, we investigate the aggregation of the type 2 diabetes-associated peptide hormone hIAPP in contact with flat and nanopatterned silicon oxide surfaces. The nanopatterned surfaces are produced by ion beam irradiation, resulting in well-defined anisotropic ripple patterns with heights and periodicities of about 1.5 and 30 nm, respectively. Using time-lapse atomic force microscopy, the morphology of the hIAPP aggregates is characterized quantitatively. Aggregation results in both amorphous aggregates and amyloid fibrils, with the presence of the nanopatterns leading to retarded fibrillization and stronger amorphous aggregation. This is attributed to structural differences in the amorphous aggregates formed at the nanopatterned surface, which result in a lower propensity for nucleating amyloid fibrillization. Our results demonstrate that nanoscale surface topography may modulate peptide and protein aggregation pathways in complex and intricate ways.
| S-EPMC8152259 | biostudies-literature
Project description:The charge transfer phenomenon of contact electrification even exists in the liquid-solid interface by a tiny droplet on the solid surface. In this work, we have investigated the contact electrification mechanism at the liquid-solid interface from the electronic structures at the atomic level. The electronic structures display stronger modulations by the outmost shell charge transfer via surface electrostatic charge perturbation than the inter-bonding-orbital charge transfer at the liquid-solid interface, supporting more factors being involved in charge transfer via contact electrification. Meanwhile, we introduce the electrochemical cell model to quantify the charge transfer based on the pinning factor to linearly correlate the charge transfer and the electronic structures. The pinning factor exhibits a more direct visualization of the charge transfer at the liquid-solid interface. This work supplies critical guidance for describing, quantifying, and modulating the contact electrification induced charge transfer systems in triboelectric nanogenerators in future works.
| S-EPMC7979908 | biostudies-literature