Browse
Submit Data
Databases
API
Help

Dataset Information

12 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Contribution of Pore-Connectivity to Permeation Performance of Silicalite-1 Membrane; Part I, Pore Volume and Effective Pore Size.

ABSTRACT: The micropore volumes and effective pore sizes of two types of silicalite-1 membranes were compared with those of a typical silicalite-1 powder. The silicalite-1 membrane with fewer grain boundaries in the membrane layer showed similar micropore volume and effective pores size to those of the silicalite-1 powder. In contrast, when the silicalite-1 membrane contained many grain boundaries, relatively small micropore volume and effective pore size were observed, suggesting that narrowing and obstruction of the micropore would occur along grain boundaries due to the disconnection of the zeolite pore. The silicalite-1 membrane with fewer grain boundaries exhibited relatively high permeation properties for C₆-C₈ hydrocarbons. There was an over 50-fold difference in benzene permeance between these two types of membranes. We concluded that it is important to reduce grain boundaries and improve pore-connectivity to develop an effective preparation method for obtaining a highly permeable membrane.

SUBMITTER: Sakai M

PROVIDER: S-EPMC8225034 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Role of Mesh Pore Size in Dynamic Membrane Bioreactors.

Project description:Two identical bench-scale Self-Forming Dynamic Membrane BioReactors (SFD MBR) were set-up and operated for the treatment of real urban wastewater. The two bioreactors were equipped with meshes of different mesh pore size. Meshes having pore size values of 20 and 50 µm were tested under solid retention time (SRT) of 15 d, whereas meshes with 50 and 100 µm pore sizes were compared under SRT of 50 d. The results of long-term experiments showed very good overall performances by all systems at the steady state. High flux (in the range 61-71 L m-2 h-1) and very good effluent quality were obtained, with average suspended solids and chemical oxygen demanding values below 10 mg L-1 and 35 mg L-1, respectively. The mesh pore size did not have a major influence on the average cleaning frequency. However, the pore size affected the effluent quality in correspondence of two particular conditions: (i) immediately after mesh cleaning; and (ii) during operation under high suction pressures (mesh clogging not promptly removed through cleaning). Moreover, the mesh cleaning frequency was observed to be dependent on the SRT. In tests with 50 d SRT, the cleaning requirements were very low (one every five days), and this limited the influence of the mesh pore size on the effluent quality. In conclusion, in SFD MBR, the role of the mesh pore size on the effluent quality may be more or less relevant depending on the operating conditions that directly influence the Dynamic Membrane formation.

| S-EPMC7915341 | biostudies-literature

Molecular Dynamics Simulations of the Permeation of Bisphenol A and Pore Formation in a Lipid Membrane.

Project description:Bisphenol A (BPA) is particularly considered as one of the most suspicious endocrine disruptors. Exposure to BPA may bring about possible human toxicities, such as cancerous tumors, birth defects and neoteny. One of the key issues to understand its toxicities is how BPA enters cells. In this paper, we perform molecular dynamics simulations to explore the interactions between BPA and a phospholipid membrane (dipalmitoylphosphatidylcholine, DPPC bilayer). The simulation results show that BPA can easily enter the membrane from the aqueous phase. With the increasing concentrations of BPA in the membrane, BPA tends to aggregate and form into cluster. Meanwhile, several DPPC lipids are pulled out from each leaflet and adsorbed on the cluster surface, leading to pore formation. Detailed observations indicate that the lipid extraction results mainly from the dispersion interactions between BPA cluster and lipid tails, as well as weak electrostatic attractions between lipid headgroups and the two hydroxyl groups on BPA. The lipid extraction and pore formation may cause cell membrane damage and are of great importance to uncover BPA's cytotoxicity.

| S-EPMC5024305 | biostudies-literature

Spatial positioning of CFTR's pore-lining residues affirms an asymmetrical contribution of transmembrane segments to the anion permeation pathway.

Project description:The structural composition of CFTR's anion permeation pathway has been proposed to consist of a short narrow region, flanked by two wide inner and outer vestibules, based on systematic cysteine scanning studies using thiol-reactive probes of various sizes. Although these studies identified several of the transmembrane segments (TMs) as pore lining, the exact spatial relationship between pore-lining elements remains under debate. Here, we introduce cysteine pairs in several key pore-lining positions in TM1, 6, and 12 and use Cd(2+) as a probe to gauge the spatial relationship of these residues within the pore. We find that inhibition of single cysteine CFTR mutants, such as 102C in TM1 or 341C in TM6, by intracellular Cd(2+) is readily reversible upon removal of the metal ion. However, the inhibitory effect of Cd(2+) on the double mutant 102C/341C requires the chelating agent dithiothreitol (DTT) for rapid reversal, indicating that 102C and 341C are close enough to the internal edge of the narrow region to coordinate one Cd(2+) ion between them. We observe similar effects of extracellular Cd(2+) on TM1/TM6 cysteine pairs 106C/337C, 107C/337C, and 107C/338C, corroborating the idea that these paired residues are physically close to each other at the external edge of the narrow region. Although these data paint a picture of relatively symmetrical contributions to CFTR's pore by TM1 and TM6, introducing cysteine pairs between TM6 and TM12 (348C/1141C, 348C/1144C, and 348C/1145C) or between TM1 and TM12 (95C/1141C) yields results that contest the long-held principle of twofold pseudo-symmetry in the assembly of ABC transporters' TMs. Collectively, these findings not only advance our current understanding of the architecture of CFTR's pore, but could serve as a guide for refining computational models of CFTR by imposing physical constraints among pore-lining residues.

| S-EPMC4845689 | biostudies-literature

Effective pore size and radius of capture for K(+) ions in K-channels.

Project description:Reconciling protein functional data with crystal structure is arduous because rare conformations or crystallization artifacts occur. Here we present a tool to validate the dimensions of open pore structures of potassium-selective ion channels. We used freely available algorithms to calculate the molecular contour of the pore to determine the effective internal pore radius (r(E)) in several K-channel crystal structures. r(E) was operationally defined as the radius of the biggest sphere able to enter the pore from the cytosolic side. We obtained consistent r(E) estimates for MthK and Kv1.2/2.1 structures, with r(E)?=?5.3-5.9?Å and r(E)?=?4.5-5.2?Å, respectively. We compared these structural estimates with functional assessments of the internal mouth radii of capture (r(C)) for two electrophysiological counterparts, the large conductance calcium activated K-channel (r(C)?=?2.2?Å) and the Shaker Kv-channel (r(C)?=?0.8?Å), for MthK and Kv1.2/2.1 structures, respectively. Calculating the difference between r(E) and r(C), produced consistent size radii of 3.1-3.7?Å and 3.6-4.4?Å for hydrated K(+) ions. These hydrated K(+) estimates harmonize with others obtained with diverse experimental and theoretical methods. Thus, these findings validate MthK and the Kv1.2/2.1 structures as templates for open BK and Kv-channels, respectively.

| S-EPMC4735802 | biostudies-literature

Effect of hydrophobized PET TeMs membrane pore-size on saline water treatment by direct contact membrane distillation.

Project description:This paper describes the desalination process by membrane distillation (MD) using track-etched membranes (TeMs). Hydrophobic track-etched membranes based on poly(ethylene terephthalate) (PET TeMs) with pore diameters from 700 to 1300 nm were prepared by UV-initiated graft polymerization of lauryl methacrylate (LMA) inside the nanochannels. Modified PET TeMs were investigated by Fourier transform infrared (FTIR) spectroscopy, atomic force microscopy (AFM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and contact wetting angle (CA) measurements. Hydrophobic PET TeMs were tested for treating saline solutions of different concentrations by the direct contact membrane distillation (DCMD) method. The influence of membrane pore diameter and salt solution concentration on the water flux and rejection degree were investigated. Membranes with CA 94 ± 4° were tested in the direct contact membrane distillation (DCMD) of 7.5-30 g L-1 saline solution. Hydrophobic membranes with large pore sizes showed water fluxes in the range of 1.88 to 11.70 kg m-2 h-1 with salt rejection values of up to 91.4%.

| S-EPMC10823361 | biostudies-literature

An amphipathic Bax core dimer forms part of the apoptotic pore wall in the mitochondrial␣membrane.

Project description:Bax proteins form pores in the mitochondrial outer membrane to initiate apoptosis. This might involve their embedding in the cytosolic leaflet of the lipid bilayer, thus generating tension to induce a lipid pore with radially arranged lipids forming the wall. Alternatively, Bax proteins might comprise part of the pore wall. However, there is no unambiguous structural evidence for either hypothesis. Using NMR, we determined a high-resolution structure of the Bax core region, revealing a dimer with the nonpolar surface covering the lipid bilayer edge and the polar surface exposed to water. The dimer tilts from the bilayer normal, not only maximizing nonpolar interactions with lipid tails but also creating polar interactions between charged residues and lipid heads. Structure-guided mutations demonstrate the importance of both types of protein-lipid interactions in Bax pore assembly and core dimer configuration. Therefore, the Bax core dimer forms part of the proteolipid pore wall to permeabilize mitochondria.

| S-EPMC8280806 | biostudies-literature

SNARE-mediated membrane fusion arrests at pore expansion to regulate the volume of an organelle.

Project description:Constitutive membrane fusion within eukaryotic cells is thought to be controlled at its initial steps, membrane tethering and SNARE complex assembly, and to rapidly proceed from there to full fusion. Although theory predicts that fusion pore expansion faces a major energy barrier and might hence be a rate-limiting and regulated step, corresponding states with non-expanding pores are difficult to assay and have remained elusive. Here, we show that vacuoles in living yeast are connected by a metastable, non-expanding, nanoscopic fusion pore. This is their default state, from which full fusion is regulated. Molecular dynamics simulations suggest that SNAREs and the SM protein-containing HOPS complex stabilize this pore against re-closure. Expansion of the nanoscopic pore to full fusion can thus be triggered by osmotic pressure gradients, providing a simple mechanism to rapidly adapt organelle volume to increases in its content. Metastable, nanoscopic fusion pores are then not only a transient intermediate but can be a long-lived, physiologically relevant and regulated state of SNARE-dependent membrane fusion.

| S-EPMC6166129 | biostudies-literature

A guide to group effective connectivity analysis, part 1: First level analysis with DCM for fMRI.

Project description:Dynamic Causal Modelling (DCM) is the predominant method for inferring effective connectivity from neuroimaging data. In the 15 years since its introduction, the neural models and statistical routines in DCM have developed in parallel, driven by the needs of researchers in cognitive and clinical neuroscience. In this guide, we step through an exemplar fMRI analysis in detail, reviewing the current implementation of DCM and demonstrating recent developments in group-level connectivity analysis. In the appendices, we detail the theory underlying DCM and the assumptions (i.e., priors) in the models. In the first part of the guide (current paper), we focus on issues specific to DCM for fMRI. This is accompanied by all the necessary data and instructions to reproduce the analyses using the SPM software. In the second part (in a companion paper), we move from subject-level to group-level modelling using the Parametric Empirical Bayes framework, and illustrate how to test for commonalities and differences in effective connectivity across subjects, based on imaging data from any modality.

| S-EPMC6711459 | biostudies-literature

Size-dependent leak of soluble and membrane proteins through the yeast nuclear pore complex.

Project description:Nuclear pore complexes (NPCs) allow selective import and export while forming a barrier for untargeted proteins. Using fluorescence microscopy, we measured in vivo the permeability of the Saccharomyces cerevisiae NPC for multidomain proteins of different sizes and found that soluble proteins of 150 kDa and membrane proteins with an extralumenal domain of 90 kDa were still partly localized in the nucleus on a time scale of hours. The NPCs thus form only a weak barrier for the majority of yeast proteins, given their monomeric size. Using FG?-mutant strains, we showed that specific combinations of Nups, especially with Nup100, but not the total mass of FG-nups per pore, were important for forming the barrier. Models of the disordered phase of wild-type and mutant NPCs were generated using a one bead per amino acid molecular dynamics model. The permeability measurements correlated with the density predictions from coarse-grained molecular dynamics simulations in the center of the NPC. The combined in vivo and computational approach provides a framework for elucidating the structural and functional properties of the permeability barrier of nuclear pore complexes.

| S-EPMC4454183 | biostudies-literature

Drug Distribution Part 2. Predicting Volume of Distribution from Plasma Protein Binding and Membrane Partitioning.

Project description:PurposeVolume of distribution is an important pharmacokinetic parameter in the distribution and half-life of a drug. Protein binding and lipid partitioning together determine drug distribution.MethodsHere we present a simple relationship that estimates the volume of distribution with the fraction of drug unbound in both plasma and microsomes. Model equations are based upon a two-compartment system and the experimental fractions unbound in plasma and microsomes represent binding to plasma proteins and cellular lipids, respectively.ResultsThe protein and lipid binding components were parameterized using a dataset containing human in vitro and in vivo parameters for 63 drugs. The resulting equation explains ~84% of the variance in the log of the volume of distribution with an average fold-error of 1.6, with 3 outliers.ConclusionsThese results suggest that Vss can be predicted for most drugs from plasma protein binding and microsomal partitioning.

| S-EPMC5285473 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data