Why POSS-Type Compounds Should Be Considered Nanomodifiers, Not Nanofillers-A Polypropylene Blends Case Study.
Ontology highlight
ABSTRACT:
SUBMITTER: Brzakalski D
PROVIDER: S-EPMC8271478 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Nanocomposites of hydrophobic organo-clay/polypropylene (organo-clay/PP) were efficiently developed through a solution-blending technique. For this, we utilized various smectite clays as host agents; namely, Na-montmorillonite (Mt, ~1000 nm), Na-fluorine mica (Mica, ~1500 nm), and Na-hectorite (Ht, ~60 nm) with varied sizes, layer charges, and aspect ratios. Such clays were functionalized with cetyltrimethylammonium (CTA) bromide via an intercalation technique to obtain hydrophobic organic clays. The as-made clay particles were further mixed with a PP/xylene solution; the latter was removed to obtain the final product of the CTA-clay/PP nanocomposite. An X-ray diffraction (XRD) analysis confirmed that there were no characteristic (001) diffraction peaks for CTA-Mica in the PP nanocomposites containing CTA-Mica, assuring the fact that the Mica layers could be completely exfoliated and thereby homogenously composited within the PP. On the other hand, the CTA-Mt and CTA-Ht incorporated composites had broader (001) peaks, which might have been due to the partial exfoliation of CTA-Mt and CTA-Ht in the composites. Among the three CTA-clay/PP nanocomposites, the CTA-Mica nanohybrid showed an enhanced thermal stability by ~42 °C compared to the intact host polymer matrix. We also noted that when the CTA-Mica content was ~9 mass % in the nanocomposites, the Young's modulus was drastically maximized to 69%. Our preliminary results therefore validated that out of the three tested clay-PP nanocomposites, the CTA-Mica nanofiller served as the best one to improve both the thermal and mechanical properties of the PP nanocomposites.
| S-EPMC9573217 | biostudies-literature
Project description:To solve the pollution problems that result from polypropylene (PP), suitable biopolymers such as poly (lactic acid) (PLA) were selected to blend with PP. Since PP/PLA blends are often exposed to the natural environment, it is necessary to study the photodegradation behavior of PP/PLA blends. In this paper, PP/PLA blends with different compositions were prepared by extrusion and subjected to the accelerated laboratory weathering equipment. The effects of compatibilizers on the degradation behavior of PP/PLA blends were also studied. The weatherability of PP/PLA blends was studied through weight loss, optical microscope, Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results revealed that PP is easy to degrade than PLA during accelerated laboratory weathering. PP/PLA blends are susceptible to the accelerated laboratory weathering process, and PP-rich and PLA-rich blends reduce the weathering resistance. Moreover, the results indicate that the initial degradation temperature, melting temperature, and crystallization temperature decrease after weathering related to the decreased thermal stability of PP/PLA blends. For instance, the initial degradation temperature of PP/PLA8.2 reduces from 332.2 °C to 320.2 °C. Moreover, the compatibilized sample is generally more resistant to weathering conditions than the uncompatibilized one due to the higher compatibility of PP and PLA.
| S-EPMC9823939 | biostudies-literature
Project description:The glycidyl-POSS (Polyhedral Oligomeric Silsesquioxanes, Polysilsesquioxane, POSS) (Gly-POSS) and trisilanolisooctyl-POSS (HO-POSS) were applied as functional additives influencing on the viscoelastic properties of the dynamic vulcanized PLA/ENR (poly(lactic acid)/epoxidized natural rubber) blends. The plasticizing effect of HO-POSS on PLA/ENR melt, leading to the decrease of complex viscosity at 160 °C, was observed. After the incorporation of Gly-POSS into PLA/ENR blends the complex viscosity increased confirming that the epoxy groups of Gly-POSS were able to react with the functional groups of ENR and the groups present at the end of PLA chains. The incorporation of Gly-POSS into 40:60 PLA/ENR blend provided significant enhancement of the storage shear modulus G' at 30 °C. Furthermore, the glass transition temperatures Tg of ENR phase for PLA/ENR/Gly-POSS blends were shifted to higher values of temperature as compared with blends modified by HO-POSS. Strong reduction of the elongation at break Eb for 40:60 PLA/ENR/Gly-POSS blend indicated that Gly-POSS particles acted as multifunctional cross-links reducing elasticity of the material. The modification of 40:60 PLA/ENR blend by HO-POSS molecules led to lower values of composting coefficient KC indicating stronger deterioration of the mechanical properties that resulted from more intense degradation processes occurring during disposal in soil.
| S-EPMC8160644 | biostudies-literature
Project description:Aqueous miscible organic layered double hydroxides (AMO-LDHs) can act as organophilic inorganic flame retardant nanofillers for unmodified non-polar polymers. In this contribution, AMO [Mg3Al(OH)8](CO3)0.5·yH2O LDH-oxidized carbon nanotube (AMO-LDH-OCNT) hybrids are shown to perform better than the equivalent pure AMO-LDH. A synergistic effect between the AMO-LDH and OCNT was observed; this endows the hybrid material with enhanced flame retardancy, thermal stability, and mechanical properties. The thermal stability of polypropylene (PP) was significantly enhanced by adding AMO-LDH-OCNT hybrids. For PP mixed with AMO-LDH-OCNT hybrids to produce a composite with 10 wt% LDH and 2 wt% OCNT, the 50% weight loss temperature was increased by 43?°C. Further, a system with 10?wt% of AMO-LDH and 1?wt% OCNT showed a peak heat release rate (PHRR) reduction of 40%, greater than the PHRR reduction with PP/20?wt% AMO-LDH (31%). The degree of dispersion (mixability) between AMO-LDH and OCNT has a significant effect on the flame retardant performance of the hybrids. In addition, the incorporation of AMO-LDH-OCNT hybrids led to better mechanical properties, such as higher tensile strength (27.5?MPa) and elongation at break (17.9%), than those composites containing only AMO-LDH (25.6?MPa and 7.5%, respectively).
| S-EPMC5067659 | biostudies-literature
Project description:Ineffective sorting of post-consumer plastics remains one of the major obstacles in the recycling of plastics. Consequently, these highly heterogeneous, mixed post-consumer plastics will end up in landfill or have to be incinerated as repurposing them directly would lead to a polymer blend with inferior quality for many end-uses. In this work, we demonstrate the use of carbon fibers (CFs) to practically upgrade the mechanical properties of mixed plastics, adding value to them. This will create a stronger demand for mixed plastics to be used in various engineering applications. Using polyethylene terephthalate (PET) and polypropylene (PP) as the model immiscible polymer blend, we showed that the incorporation of CFs increased the tensile, flexural, and single-edge notched fracture toughness of the resulting CF-reinforced PET/PP composite blends. Despite the high environmental burden associated with the production of CFs, cradle-to-grave life-cycle analysis showed that CF-reinforced PET/PP composites have a lower environmental impact than the life-cycle scenarios of "doing nothing" and repurposing immiscible PET/PP blends as it is without CF reinforcement. This can be attributed to the weight saving achieved, a direct result of their higher mechanical performance. Our work opens up opportunities for the use of mixed plastics in various higher value applications such that they can be diverted away from landfill or incineration, in line with the concept of circular economy.
| S-EPMC9112279 | biostudies-literature
Project description:This paper provides evidence and discusses the variability in the thermomechanical behaviour of virgin and recycled polypropylene/high-density polyethylene blends without the addition of other components, which is sparse in the literature. Understanding the performance variability in recycled polymer blends is of critical importance in order to facilitate the re-entering of recycled materials to the consumer market and, thus, contribute towards a circular economy. This is an area that requires further research due to the inhomogeneity of recycled materials. Therefore, the thermal and mechanical properties of virgin and recycled polypropylene/high-density polyethylene blends were investigated systematically. Differential scanning calorimetry concludes that both the recycled and virgin blends are immiscible. Generally, recycled blends have lower overall crystallinity and melting temperatures compared with virgin blends while, remarkably, their crystallisation temperatures are compared favourably. Dynamical mechanical analysis showed little variation in the storage modulus of recycled and virgin blends. However, the alpha and beta relaxation temperatures are lower in recycled blends due to structural deterioration. Deterioration in the thermal and mechanical properties of recycled blends is thought to be caused by the presence of contaminants and structural degradation during reprocessing, resulting in shorter polymeric chains and the formation of imperfect crystallites. The tensile properties of recycled blends are also affected by the recycling process. The Young's modulus and yield strength of the recycled blends are inferior to those of virgin blends due to the deterioration during the recycling process. However, the elongation at break of the recycled blends is higher compared with the virgin blends, possibly due to the plasticity effect of the low-molecular-weight chain fragments.
| S-EPMC10647352 | biostudies-literature
Project description:We found in our previous study that layered double hydroxides (LDHs) which undergo aqueous miscible organic solvent treatment (AMOST) can tune the hydrophobicity surface of LDHs to be hydrophobic, and then the solvent mixing method can be used to prepare polymer/LDH nanocomposites. However, flame retardant property is not very high if LDHs are only used. In this present work, ammonium polyphosphate (APP) intercalated LDHs and zinc borate (ZB) was incorporated into a polypropylene (PP) matrix using the solvent mixing method. The structures, morphologies, and performance of the composites were characterized carefully. The peak heat release rate (PHRR) reduction of PP containing 10 and 20 wt % APP-LDH reached 27% and 55%, respectively, which increased up to 63% compared with PP/CO₃-LDH. After incorporating 2 wt % ZB in the PP/APP-LDH system, the flame retardant property was further improved. Polypropylene composites with 20 wt % APP-LDH and 2 wt % ZB showed a 58% PHRR reduction. In addition, thermogravimetric analyzer (TGA) results indicated that the addition of APP-LDH and ZB improved the temperature at 50% weight loss (T50%) and the char formation of the materials significantly.
| S-EPMC6403616 | biostudies-literature
Project description:Fiber-reinforcement is a well-established technique to enhance the tensile properties of polymer composites, which is achieved via changing the reinforcing material concentration and orientation. However, the conventional method can be costly and may lead to poor compatibility issues. To overcome these challenges, we demonstrate the use of micro-/nanolayer (MNL) extrusion technology to tune the mechanical properties of polypropylene (PP)/polyethylene terephthalate (PET) fibrillar blends. PET nanofibers-in-PP microfiber composites, with 3, 7, and 15 wt.% PET, are first prepared using a spunbond system to induce high aspect-ratio PET nanofibers. The PP/PET fibers are then reprocessed in an MNL extrusion system and subjected to shear and extensional flow fields in the channels of the uniquely designed layer multipliers. Increasing the mass flow rate and number of multipliers is shown to orient the PET nanofibers along the machine direction (MD), as confirmed via scanning electron microscopy. Tensile tests reveal that up to a 45% and 46% enhancement in elastic modulus and yield strength are achieved owing to the highly aligned PET nanofibers along the MD under strongest processing conditions. Overall, the range of tensile properties obtained using MNL extrusion implies that the properties of fiber-reinforced composites can be further tuned by employing this processing technique.
| S-EPMC7694209 | biostudies-literature
Project description:Microfibrillar and droplet morphology of polypropylene (PP) phase dispersed in polypropylene (PS) was fabricated by using melt-extrusion. This morphology was obtained by introducing isotactic PP (20 wt.%) with different viscosity in the PS matrix (80 wt.%). Furthermore, the rheological properties of the blend investigated as a function of the viscosity ratio K. The variations in blend morphology were related to crystallization, melting properties, and viscoelasticity. The blends with K >> 1 develop a fine morphology with PP microfibrils along the flow direction, while diameters of the dispersed PP droplets gradually increase with lower values of K = 1, or K << 1. Crystallinity of the prepared blends significantly decreases compared to neat PP, while the microfibrillar morphology induces homogeneous crystallization with small crystallites. This is reflected in a decrease of the crystallization temperature, small loss in the crystallinity, and lower melting temperature of the PS80/PP20 blend compared to neat PP. The storage moduli, loss moduli, and complex viscosity are highest for the microfibrillar morphology that presents retarded relaxation. The rheological properties are dominated by the dispersed phase (K > 1), or matrix (K < 1). The variation in blend properties with microfibrillar morphology can be clearly distinguished from heterogeneous blends containing PP droplets, providing an efficient tool to create a binary blend with unique properties.
| S-EPMC7078875 | biostudies-literature
Project description:The effect of the anchoring group on the detailed polymerization kinetics was investigated using monomethacryloxy-heptaisobutyl POSS (1M-POSS). This compound was copolymerized with lauryl methacrylate (LM) as the base monomer, at various molar ratios. The process was initiated photochemically. The polymerization kinetics were followed by photo-DSC and photorheology while the polymers were characterized by nuclear magnetic resonance (NMR), gel permeation chromatography (GPC), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). For comparison, a methacrylate containing the branched siloxy-silane group (TSM) was also studied. It was found that the modifiers with a bulky substituent have a dual effect on the termination process: (i) At low concentrations, they increase the molecular mobility by increasing the free volume fraction, which leads to an acceleration of the termination and slows the polymerization; while (ii) at higher concentrations, they retard molecular motions due to the "anchor effect" that suppresses the termination, leading to acceleration of the polymerization. The anchor effect can also be considered from a different point of view: The possibility of anchoring a monomer with a long substituent (LM) around the POSS cage, which can further enhance propagation. These conclusions were derived based on kinetic results, determination of polymerization rate coefficients, and copolymer analysis.
| S-EPMC6473415 | biostudies-literature