Evolution of Surface Morphology of Spin-Coated Poly(methyl methacrylate) Thin Films.
Ontology highlight
ABSTRACT:
SUBMITTER: Chapman N
PROVIDER: S-EPMC8271514 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Whilst the significance of substrate topography as a regulator of cell function is well established, a systematic analysis of the principles underlying this is still unavailable. Here we evaluate the hypothesis that surface energy plays a decisive role in substrate-mediated modulation of cell phenotype by evaluation of cell behaviour on synthetic microstructures exhibiting pronounced differences in surface energy. These microstructures, specifically cubes and walls, were fabricated from a biocompatible base polymer, poly(methyl methacrylate), by variotherm injection molding. The dimensions of the cubes were 1 μm x 1 μm x 1 μm (height x width x length) with a periodicity of 1:1 and 1:5 and the dimensions of the walls 1 μm x 1 μm x 15 mm (height x width x length) with a periodicity of 1:1 and 1:5. Mold inserts were made by lithography and electroplating. The surface energy of the resultant microstructures was determined by static contact angle measurements. Light scanning microscopy of the morphology of NT2/D1 and MC3T3-E1 preosteoblast cells cultured on structured PMMA samples in both cases revealed a profound surface energy dependence. "Walls" appeared to promote significant cell elongation, whilst a lack of cell adhesion was observed on "cubes" with the lowest periodicity. Contact angle measurements on walls revealed enhanced surface energy anisotropy (55 mN/m max., 10 mN/m min.) causing a lengthwise spreading of the test liquid droplet, similar to cell elongation. Surface energy measurements for cubes revealed increased isotropic hydrophobicity (87° max., H2O). A critical water contact angle of ≤ 80° appears to be necessary for adequate cell adhesion. A "switch" for cell adhesion and subsequently cell growth could therefore be applied by, for example, adjusting the periodicity of hydrophobic structures. In summary cell elongation on walls and a critical surface energy level for cell adhesion could be produced for NT2/D1 and MC3T3-E1 cells by symmetrical and asymmetrical energy barrier levels. We, furthermore, propose a water-drop model providing a common physicochemical cause regarding similar cell/droplet geometries and cell adhesion on the investigated microstructures.
| S-EPMC6521382 | biostudies-literature
Project description:Poly(methyl methacrylate) (PMMA) is a glassy engineering polymer that finds extensive use in a number of applications. Over the past decade, thin films of PMMA were combined with graphene or other two-dimensional materials for applications in the area of nanotechnology. However, the effect of size upon the mechanical behavior of this thermoplastic polymer has not been fully examined. In this work, we adopted a homemade nanomechanical device to assess the yielding and fracture characteristics of freestanding, ultrathin (180-280 nm) PMMA films of a loaded area as large as 0.3 mm2. The measured values of Young's modulus and yield strength were found to be broadly similar to those measured in the bulk, but in contrast, all specimens exhibited a quite surprisingly high strain at failure (>20%). Detailed optical examination of the specimens during tensile loading showed clear evidence of craze development which however did not lead to premature fracture. This work may pave the way for the development of glassy thermoplastic films with high ductility at ambient temperatures.
| S-EPMC8015101 | biostudies-literature
Project description:In search of a suitable single-source precursor for the deposition of nanostructured PbS thin films at moderate temperatures under ambient conditions, we have synthesized the ligand N-(thiomorpholine-4-carbothioyl)benzamide and its corresponding lead(II) complex. The structures of both compounds were determined by single-crystal X-ray diffraction. In the complex, two ligands coordinate to a lead(II) atom in hemi-directed geometry through S and O atoms. Secondary intermolecular Pb⋅⋅⋅S interactions group the complexes into pairs. As bulk powders, both the ligand and complex show nominal composition and purity as evidenced by elemental analysis, 1 H NMR and IR spectroscopy. Thermal analysis of the lead(II) complex was carried out to understand its thermal decomposition behaviour for establishing a thin film fabrication protocol. Thin films of phase-pure PbS were fabricated using this new molecular precursor at the comparatively low annealing temperature of 250 °C. The film showed nanoparticles with cuboidal morphology and a blue-shifted optical absorption.
| S-EPMC10104949 | biostudies-literature
Project description:In this work, nanocomposites of poly(methyl methacrylate) (PMMA) with cellulose nanofiber (CNF) were prepared by a solution casting technique. CNF was modified by propionic anhydride (PA) to form surface-propionylated CNF (CNFp) to improve its compatibility with the PMMA matrix. CNF, CNFp, and acetylated CNF were compared with respect to their influence as fillers in PMMA composite films by ultraviolet-visible transmittance, haze values, tensile strength testing, and water contact angle measurement. It was demonstrated that 1 wt % of CNFp has good compatibility and uniform dispersion in the PMMA matrix, as demonstrated by the formation of a smooth surface composite film with good transparency, enhanced tensile properties, improved toughness, and lower wettability. Therefore, PMMA/CNFp composite films have great potential for use in several applications such as lightweight transparent materials, window substitutes, and see-through packaging.
| S-EPMC8153788 | biostudies-literature
Project description:Atom transfer radical polymerization (ATRP) is commonly used to grow polymer brushes from Au surfaces, but the resulting film thicknesses are usually significantly less than with ATRP from SiO(2) substrates. On Au, growth of poly(methyl methacrylate) (PMMA) blocks from poly(tert-butyl acrylate) brushes occurs more rapidly than growth of PMMA from initiator monolayers, suggesting that the disparity between growth rates from Au and SiO(2) stems from the Au surface. Radical quenching by electron transfer from Au is probably not the termination mechanism because polymerization from thin, cross-linked initiators gives film thicknesses that are essentially the same as the thicknesses of films grown from SiO(2) under the same polymerization conditions. However, this result is consistent with termination through desorption of thiols from noncross-linked films, and reaction of these thiols with growing polymer chains. The enhanced stability of cross-linked initiators allows ATRP at temperatures up to ?100 °C and enables the growth of thick films of PMMA (350 nm), polystyrene (120 nm) and poly(vinyl pyridine) (200 nm) from Au surfaces in 1 h. At temperatures >100 °C, the polymer brush layers delaminate as large area films.
| S-EPMC3193157 | biostudies-literature
Project description:A key question in the field of ceramics and catalysis is how and to what extent residual water in the reactive environment of a metal oxide particle powder affects particle coarsening and morphology. With X-ray Diffraction (XRD) and Transmission Electron Microscopy (TEM), we investigated annealing-induced morphology changes on powders of MgO nanocubes in different gaseous H2O environments. The use of such a model system for particle powders enabled us to describe how adsorbed water that originates from short exposure to air determines the evolution of MgO grain size, morphology, and microstructure. While cubic nanoparticles with a predominant abundance of (100) surface planes retain their shape after annealing to T = 1173 K under continuous pumping with a base pressure of water p(H2O) = 10-5 mbar, higher water partial pressures promote mass transport on the surfaces and across interfaces of such particle systems. This leads to substantial growth and intergrowth of particles and simultaneously favors the formation of step edges and shallow protrusions on terraces. The mass transfer is promoted by thin films of water providing a two-dimensional solvent for Mg2+ ion hydration. In addition, we obtained direct evidence for hydroxylation-induced stabilization of (110) faces and step edges of the grain surfaces.
| S-EPMC6175089 | biostudies-literature
Project description:Multicomponent polymer particles with specific morphology are promising materials exhibiting novel functionality which cannot be obtained with single-component polymer particles. Particularly, the preparation of such kinds of polymer particles involving electrically or optically active conjugated polymers with uniform size is a challenging subject due to their intense demands. Here, microspheres of binary polymer blend consisting of poly(4-butyltriphenylamine) (PBTPA)/poly(methyl methacrylate) (PMMA) (1:1 in weight) were produced via a microfluidic emulsification with a Y-shaped microreactor, and a subsequent solvent evaporation method. The flow rate of the dispersed phase (polymer solution) was fixed to 7 µL/min, and 140 or 700 µL/min of the flow rate of the continuous phase (aqueous 0.6 wt % of poly(vinyl alcohol) (PVA) solution) was utilized to produce the dispersion with different diameter. The concentration of dispersed phase was adjusted to 0.1 or 1.0 w/v%. Core-shell, Janus and dumbbell type microspheres were obtained dependent on the flow rate of continuous phase. Incomplete core-shell type microspheres were produced for the blend involving low molecular weight PMMA. Complex Janus and core-shell type microspheres were fabricated by the addition of sodium dodecyl sulfate (SDS) to continuous phase. It is found that final morphologies are strongly dependent on the initial conditions of dispersion including the particle size suggesting that the morphologies are governed by the kinetical factors together with the conventionally accepted thermodynamic ones.
| S-EPMC5951466 | biostudies-literature
Project description:Block copolymer (BCP) thin films prepared by dip-coating are increasingly investigated, owing to the many promising application areas, the facility, and the industrial scalability of this technique. Yet, the effect of different dip-coating parameters on BCP nanostructure formation is still underdeveloped and the results of previous literature are limited to a few block copolymers. Here, we study the effect of the withdrawal rate and solvent selectivity on the morphology evolution of dip-coated polystyrene-b-poly(ethylene oxide) thin films by applying a wide range of dip-coating speeds and altering the volume ratio of the tetrahydrofuran-water solvent system. The dip-coated films were characterized using atomic force microscopy and ellipsometry. The nanodomain morphology, its feature sizes, its spanning, and the degree of ordering were investigated with regard to different dip-coating parameters. Notably, we have obtained a hexagonally packed BCP pattern with long-range order without the need for post-annealing processes. Overall, a solid understanding of the parameters affecting the formed surface patterns and their interplay was attained and explained, extending the knowledge of this field to more materials.
| S-EPMC9418883 | biostudies-literature
Project description:This paper illustrates the effect of substrate topography on morphology evolution in nanoporous gold (np-Au) thin films. One micron-high silicon ridges with widths varying between 150 nm to 50 µm were fabricated and coated with 500 nm-thick np-Au films obtained by dealloying sputtered gold-silver alloy films. Analysis of scanning electron micrographs of the np-Au films following dealloying and thermal annealing revealed two distinct regimes where the ratio of film thickness to ridge width determines the morphological evolution of np-Au films.
| S-EPMC4587536 | biostudies-literature
Project description:The surfaces of polymeric materials are thermodynamically unstable, and the glass-transition temperature (Tg) is significantly lower than that in the bulk material. However, the mobility of the chains at the top of the surface has never been directly evaluated. In this study, the movements of the topmost chains of poly(methyl methacrylate) (PMMA) and polystyrene (PS) bulk films were observed in situ at high temperatures with atomic force microscopy in tapping mode. PMMA and PS chains started moving at ∼97 and ∼50 °C, respectively, which were slightly and significantly below the values of their bulk Tg (PMMA, 108 °C; PS, 104 °C), respectively. The activation energies of the apparent diffusion constants of PMMA and PS, derived by particle image velocimetry analysis, were 193 and 151 kJ mol-1, respectively, and reasonable for the glass transition. Movements of isolated PMMA chains deposited on a PMMA film by the Langmuir-Blodgett technique were also observed and confirmed to be essentially the same as those on the PMMA film surface.
| S-EPMC9671121 | biostudies-literature