Browse
Submit Data
Databases
API
Help

Dataset Information

35 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Calcination of Clay Raw Materials in a Fluidized Bed.

ABSTRACT: Clay raw materials are diverse in terms of their mineral composition, as well as the content of colouring oxides and their physical properties. Determining the suitability of raw materials for various purposes requires comprehensive studies on their properties, as well as their appropriate correction, which is possible through the use of appropriate modification techniques. One of the most commonly used technologies for the enrichment of clay raw materials is to subject them to high temperatures, which, depending on the temperature regime used in the technological process, may cause the decomposition and removal of some addditional components (e.g., carbonates), as well as the removal of water and dehydroxylation of clay minerals, reversible structural changes, and the complete and permanent reconstruction of the mineral phases. This paper presents a new application for fluidization technology in the calcination of clay raw materials. The results of the experiment show that the fluidization method is competitive compared to the technologies that have been used so far, as a result of, inter alia, the much shorter time period required to carry out the calcination process and, consequently, the much lower energy expenditure, the high efficiency of burning coal, and the lower CO₂ emissions resulting from the mixing taking place in the reactor.

SUBMITTER: Kaczynska K

PROVIDER: S-EPMC8303566 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Fluidized Bed Chemical Vapor Deposition on Hard Carbon Powders to Produce Composite Energy Materials.

Project description:Herein, we report a general route for the uniform coating of hard carbon (HC) powders via fluidized bed chemical vapor deposition. Carbon-based fine powders are excellent substrate materials for many catalytic and electrochemical applications but intrinsically difficult to fluidize and prone to elutriation. The reactor was designed to achieve as much retention of powders as possible, supported by a computational fluid dynamics study to assess the hydrodynamic behavior for varying gaseous flow rates. Solutions of the tin seleno- and thio-ether complexes [SnCl4{nBuSe(CH2)3SenBu}] and [SnCl4{nBuS(CH2)3SnBu}] were used as single source precursors and injected at high temperature into a fluidized bed of HC powders under nitrogen flow. The method allowed for the synthesis of HC-SnSx-SnSe2 composites at the gram scale with potential applications in electrocatalysis and sodium-ion battery anodes.

| S-EPMC10955755 | biostudies-literature

fluidized bed organisms

Project description:microorganisms obtained from fungal fluidized bed reactor Genome sequencing and assembly

| PRJNA574236 | ENA

Antioxidant Activity of the Lignins Derived from Fluidized-Bed Fast Pyrolysis.

Project description:A challenge in recent years has been the rational use of forest and agriculture residues for the production of bio-fuel, biochemical, and other bioproducts. In this study, potentially useful compounds from pyrolytic lignins were identified by HPLC-MS/MS and untargeted metabolomics. The metabolites identified were 2-(4-allyl-2-methoxyphenoxy)-1-(4-hydroxy-3-methoxyphenyl)-1-propanol, benzyl benzoate, fisetinidol, phenyllactic acid, 2-phenylpropionic acid, 6,3'-dimethoxyflavone, and vanillin. The 2,2-diphenyl-1-picrylhydrazyl radical scavenging activity (DPPH), trolox equivalent antioxidant capacity (TEAC), and total phenolics content (TPC) per gram of pyrolytic lignin ranged from 14 to 503 mg ascorbic acid equivalents, 35 to 277 mg trolox equivalents, and 0.42 to 50 mg gallic acid equivalents, respectively. A very significant correlation was observed between the DPPH and TPC (r = 0.8663, p ? 0.0001), TEAC and TPC (r = 0.8044, p ? 0.0001), and DPPH and TEAC (r = 0.8851, p ? 0.0001). The polyphenolic compounds in the pyrolytic lignins which are responsible for radical scavenging activity and antioxidant properties can be readily profiled with HPLC-MS/MS combined with untargeted metabolomics. The results also suggest that DPPH, TEAC, and TPC assays are suitable methods for the measurement of antioxidant activity in a variety of pyrolytic lignins. These data show that the pyrolytic lignins can be considered as promising sources of natural antioxidants and value-added chemicals.

| S-EPMC6155384 | biostudies-literature

Effect of bed characters on the direct synthesis of dimethyldichlorosilane in fluidized bed reactor.

Project description:This paper presents the numerical investigation of the effects of the general bed characteristics such as superficial gas velocities, bed temperature, bed heights and particle size, on the direct synthesis in a 3D fluidized bed reactor. A 3D model for the gas flow, heat transfer, and mass transfer was coupled to the direct synthesis reaction mechanism verified in the literature. The model was verified by comparing the simulated reaction rate and dimethyldichlorosilane (M2) selectivity with the experimental data in the open literature and real production data. Computed results indicate that superficial gas velocities, bed temperature, bed heights, and particle size have vital effect on the reaction rates and/or M2 selectivity.

| S-EPMC4649753 | biostudies-other

Extraction of Valuable Metals and Preparation of Mesoporous Materials from Circulating Fluidized Bed-Derived Fly Ash via an Acid-Alkali-Based Alternate Method.

Project description:Stringent leaching conditions including high pressure, temperature, and chemical consumption limit the extraction of valuable metals from circulating fluidized bed-derived high-alumina fly ash (CFB-HAFA) via the acid leaching method. In the present study, a complex utilization of CFB-HAFA, including the extraction of valuable metals (Al, Li, and Ga) and preparation of mesoporous material, is realized via a moderate acid-alkali-based alternate method. The results show that 82, 78, and 69% of Al, Li, and Ga, respectively, in CFB-HAFA are extracted by two treatments of acid leaching under moderate conditions of 15 wt % HCl concentration and 90 °C leaching temperature. The leaching behaviors of metals follow a shrinking core model, and the leaching process is first controlled by the surface chemical reaction at the initial stage and H+ diffusion thereafter. Numerous slit-shaped mesopores form in the residue during acid leaching. The final residue with a specific surface area of 273 m2/g can be used as an efficient adsorbent for removing methylene blue from dye wastewater. The maximum adsorption capacity is approximately 140.0 mg/g at room temperature. The Langmuir adsorption isotherm and pseudo second-order model can well describe the adsorption process and kinetics, implying that the adsorption is a monolayer and chemical adsorption.

| S-EPMC7726952 | biostudies-literature

Integrated Purification and Formulation of an Active Pharmaceutical Ingredient via Agitated Bed Crystallization and Fluidized Bed Processing.

Project description:Integrated API and drug product processing enable molecules with high clinical efficacy but poor physicochemical characteristics to be commercialized by direct co-processing with excipients to produce advanced multicomponent intermediates. Furthermore, developing isolation-free frameworks would enable end-to-end continuous processing of drugs. The aim of this work was to purify a model API (sodium ibuprofen) and impurity (ibuprofen ethyl ester) system and then directly process it into a solid-state formulation without isolating a solid API phase. Confined agitated bed crystallization is proposed to purify a liquid stream of impure API from 4% to 0.2% w/w impurity content through periodic or parallelized operations. This stream is combined with a polymer solution in an intermediary tank, enabling the API to be spray coated directly onto microcrystalline cellulose beads. The spray coating process was developed using a Design of Experiments approach, allowing control over the drug loading efficiency and the crystallinity of the API on the beads by altering the process parameters. The DoE study indicated that the solvent volume was the dominant factor controlling the drug loading efficiency, while a combination of factors influenced the crystallinity. The products from the fluidized bed are ideal for processing into final drug products and can subsequently be coated to control drug release.

| S-EPMC9145956 | biostudies-literature

Spout Fluidized Bed Assisted Preparation of Poly(tannic acid)-Coated Urea Fertilizer.

Project description:Slow-release fertilizers (SRFs) have been widely used to reduce environment pollution derived from excessive nutrients. Coated fertilizers have been designed and prepared using various materials. However, development of new green coating materials and simple process is still a huge challenge. In this study, tannic acid (TA), a natural polyphenol, was used to prepare poly(tannic acid) (PTA)-coated fertilizers with urea prills as the core, and the technology of the coating process in a spout fluidized bed was developed. PTA coating could be formed rapidly by the fast oxidation of TA by an oxidation solution containing CuSO4 and H2O2. The coated urea release behavior was systematically studied in water and soil. In both water and soil, the release rate of nitrogen from coated urea is much slower than that from raw urea. Raw urea was completely dissolved within 30 min, while 27% of urea was released from coated urea. The pot experiments indicated that coated urea has a positive effect on the plant growth as well. Our results provide an effective method to prepare environment-friendly SRFs, indicating a promising application in sustainable agriculture.

| S-EPMC6977027 | biostudies-literature

Microbiota in fluidized bed membrane bioreactor

Project description:An aerated and fluidized bed membrane bioreactor for effective wastewater treatment with low membrane fouling

| PRJEB13756 | ENA

Response surface data for sensitivity study of industrial spray injected fluidized bed reactor.

Project description:An industrial fluidized bed reactor was designed to convert an aqueous solid laden stream into a consistent granular product. CFD simulations were run using the MFiX two-fluid model for a fluidizing bed operating at 650?°C. A set of simulations were run over a Latin-hypercube sample of five model parameters - bed particle size, bed particle density, coal particle size, spray feed flow rate, and fluidizing gas flow rate. Data from the simulations were collected on three quantities of interest - bed differential temperature, low solids velocity, and bed void fraction. The data presented here is the full set of response surfaces generated using the process Gaussian response surface model in the Dakota toolkit, as well as the table of data for coefficients of the fitted model. The fits to the five-dimensional Gaussian Process models were 0.7797, 0.8664, and 0.9440 for the temperature, velocity, and solids packing, respectively.

| S-EPMC6197788 | biostudies-literature

Production of bio-oil from Tung seed residues in a fluidized-bed reactor.

Project description:The current paper presents research on bio-oil production from Tung seed residues fed at 500 g/h via fast pyrolysis in a fluidized-bed. The objective was to investigate the influence of temperature on bio-oil production in a pyrolysis process. Three portions Tung residues were studied, Tung seed outer shells (TO), Tung seed inner shells (TI), and pressed residues of oil seeds (RS), all having particle sizes of 0.150-0.500 mm. The process temperatures were 350-500 °C. The physical and chemical properties of pressed residue particles were characterized by ASTM standard methods. Bio-oil component identification was done using GC-MS. Experimentally derived data showed an optimal pyrolysis temperatures for all three types of Tung residues (TO, TI and RS) of 400 °C, yielding respective maximum bio-oil yields of 53.46, 52.81, and 62.85 wt% on a dry basis (db). Apart from having highest bio-oil yield, RS produced bio-oil with the highest carbon content, leading to its greatest lower heating value (LHV), 28.05 MJ/kg (db). The main bio-oil components were acids, nitrogen compounds, and hydrocarbons. Char yield was reduced with increased temperature. Tung seed outer shells produced the highest char level (39.26 wt%) while RS gave highest char quality in term of density and heating value.

| S-EPMC11002048 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data