Extrusion Based 3D Printing of Sustainable Biocomposites from Biocarbon and Poly(trimethylene terephthalate).
Ontology highlight
ABSTRACT:
SUBMITTER: Diederichs E
PROVIDER: S-EPMC8305183 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:There are millions of tons of post-food processing residues discarded annually. Currently, these waste materials are discarded to landfill, used as animal feed or incinerated. This suggests that there are potential uses for these materials in value-added applications. This work focuses on the characterization and valorization of peanut hulls through the generation of green composites. Peanut hulls were pyrolyzed at 500?°C and analyzed to discover their unique surface morphology and relatively low ash content. Raman spectral analysis determined ID/IG values of 0.74 for the samples, suggesting greater graphitic content than disordered carbon content. Such results were confirmed in X-ray diffraction analysis by the presence of (002) and (100) planes. Partially biobased engineering thermoplastic, poly(trimethylene terephthalate) (PTT), was combined with 20 wt.% biocarbon. The tensile and flexural moduli improved with the addition of biocarbon, and the bio-content increased from 35 to 48 wt.% as compared to neat PTT. The higher temperature biocarbon was found to have superior performance over the lower temperature sample. The enhanced sustainability of these materials suggested that peanut hulls can be valorized via thermochemical conversion to generate value-added products. Future works could focus on the optimization of these materials for non-structural automotive components or electrical housings.
| S-EPMC7039894 | biostudies-literature
Project description:Achieving sustainability in composite materials for high-performance applications is a key issue in modern processing technologies. In this work, the structure-property relationships of injection molded polypropylene (PP)/biocarbon composites were investigated with a focus on the thermal properties and specific emphasis on the coefficient of linear thermal expansion (CLTE). Biocomposites were produced using 30 wt.% biocarbon in a PP matrix, and two different sources of biocarbon produced at ~650 and 900 °C were used. The overall results were compared with 30 wt.% glass- and talc-filled PP composites. Due to the lamellar morphology of the talc developed during the extrusion-injection molding processing, talc-filled composites showed an increase in the CLTE in the normal direction (ND), and a reduction in the flow direction (FD) with respect to the neat polymer. Glass fiber composites also showed an improvement in the CLTE with respect to the neat polymer. However, the biocarbon-based composites showed the best properties in the ND, with improved values in biocarbon produced at higher temperature. The FD values for both biocarbon composites were improved with respect to the matrix, while biocarbon created at lower temperature showed slightly lower expansion values. A comprehensive explanation of these overall phenomena is supported by a series of morphological, thermal, mechanical and rheological tests.
| S-EPMC6891267 | biostudies-literature
Project description:Polypropylene (PP) is an attractive polymer for use in automotive parts due to its ease of processing, hydrophobic nature, chemical resistance and low density. The global shift towards eliminating non-renewable resource consumption has promoted research of sustainable biocarbon (BioC) filler in a PP matrix, but this material often leads to reduction in composite strength and requires additional fillers. Graphene nano-platelets (GnPs) have been the subject of considerable research as a nanofiller due to their strength, while maleic anhydride grafted polypropylene (MA-g-PP) is a commonly used compatibilizer for improvement of interfacial adhesion in composites. This study compared the thermo-mechanical properties of PP/BioC/MA-g-PP/GnP composites with varying wt.% of GnP. Morphological analysis revealed uniform dispersion of BioC, while significant agglomeration of GnPs limited their even dispersion throughout the PP matrix. In the optimal blend of 3 wt.% GnP and 17 wt.% BioC biocontent, tensile strength and modulus increased by ~19% and ~22% respectively, as compared to 20 wt.% BioC biocomposites. Thermal stability and performance enhancement occurred through incorporation of the fillers. Thus, hybridization of fillers in the compatibilized matrix presents a promising route to the enhancement of material properties, while reducing petroleum-based products through use of sustainable BioC filler in composite structures.
| S-EPMC7329909 | biostudies-literature
Project description:The primary focus of this work is to present the current challenges of printing scaffolds with concentration gradients of nanoparticles with an aim to improve the processing of these scaffolds. Furthermore, we address how print fidelity is related to material composition and emphasize the importance of considering this relationship when developing complex scaffolds for bone implants. The ability to create complex tissues is becoming increasingly relevant in the tissue engineering community. For bone tissue engineering applications, this work demonstrates the ability to use extrusion-based printing techniques to control the spatial deposition of hydroxyapatite (HA) nanoparticles in a 3D composite scaffold. In doing so, we combined the benefits of synthetic, degradable polymers, such as poly(propylene fumarate) (PPF), with osteoconductive HA nanoparticles that provide robust compressive mechanical properties. Furthermore, the final 3D printed scaffolds consisted of well-defined layers with interconnected pores, two critical features for a successful bone implant. To demonstrate a controlled gradient of HA, thermogravimetric analysis was carried out to quantify HA on a per-layer basis. Moreover, we non-destructively evaluated the tendency of HA particles to aggregate within PPF using micro-computed tomography (?CT). This work provides insight for proper fabrication and characterization of composite scaffolds containing particle gradients and has broad applicability for future efforts in fabricating complex scaffolds for tissue engineering applications.
| S-EPMC5597446 | biostudies-literature
Project description:The incorporation of poly(lactic acid) (PLA) and poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) as a partial biobased polymer substitute for polypropylene (PP) was investigated. The ternary blends were prepared through melt compounding extrusion followed by injection molding techniques with a constant biopolymer ratio of 30 wt %. Further addition of pyrolyzed miscanthus-based carbon was carried out to establish a contrast between talc-filled PP. When the morphology of the biopolymer minor phase was analyzed theoretically using contact angle for interfacial tension and spreading coefficient values along with solubility parameter calculations and via scanning electron microscopy imaging, the core-shell architecture was found with the PHBV encasing the PLA phase. Mechanical testing of the materials showed that only the tensile properties were reduced for all samples, whereas the impact strength was increased above the neat PP. With inclusion of the biobased carbon filler into the blend system, the thermomechanical properties were elevated above that of the PP matrix. The final properties of the multiphase polymeric composites are found to be related to the morphology obtained and inherent properties of the individual constituents.
| S-EPMC6044961 | biostudies-literature
Project description:Hydrogels are an interesting class of materials used in extrusion-based 3D printing, e.g., for drug delivery or tissue engineering. However, new hydrogel formulations for 3D printing as well as a detailed understanding of crucial formulation properties for 3D printing are needed. In this contribution, hydrogels based on poly(ethylene glycol) diacrylate (PEG-DA) and the charged monomers 3-sulfopropyl acrylate and [2-(acryloyloxy)ethyl]trimethylammonium chloride are formulated for 3D printing, together with Poloxamer 407 (P407). Chemical curing of formulations with PEG-DA and up to 5% (w/w) of the charged monomers was possible without difficulty. Through careful examination of the rheological properties of the non-cured formulations, it was found that flow properties of formulations with a high P407 concentration of 22.5% (w/w) possessed yield stresses well above 100 Pa together with pronounced shear thinning behavior. Thus, those formulations could be processed by 3D printing, as demonstrated by the generation of pyramidal objects. Modelling of the flow profile during 3D printing suggests that a plug-like laminar flow is prevalent inside the printer capillary. Under such circumstances, fast recovery of a high vicosity after material deposition might not be necessary to guarantee shape fidelity because the majority of the 3D printed volume does not face any relevant shear stress during printing.
| S-EPMC6209279 | biostudies-other
Project description:Additive manufacturing promises to revolutionize manufacturing industries. However, 3D printing of novel build materials is currently limited by constraints inherent to printer designs. In this work, a bench-top powder melt extrusion (PME) 3D printer head was designed and fabricated to print parts directly from powder-based materials rather than filament. The final design of the PME printer head evolved from the Rich Rap Universal Pellet Extruder (RRUPE) design and was realized through an iterative approach. The PME printer was made possible by modifications to the funnel shape, pressure applied to the extrudate by the auger, and hot end structure. Through comparison of parts printed with the PME printer with those from a commercially available fused filament fabrication (FFF) 3D printer using common thermoplastics poly(lactide) (PLA), high impact poly (styrene) (HIPS), and acrylonitrile butadiene styrene (ABS) powders (< 1 mm in diameter), evaluation of the printer performance was performed. For each build material, the PME printed objects show comparable viscoelastic properties by dynamic mechanical analysis (DMA) to those of the FFF objects. However, due to a significant difference in printer resolution between PME (X-Y resolution of 0.8 mm and a Z-layer height calibrated to 0.1 mm) and FFF (X-Y resolution of 0.4 mm and a Z-layer height of 0.18 mm), as well as, an inherently more inconsistent feed of build material for PME than FFF, the resulting print quality, determined by a dimensional analysis and surface roughness comparisons, of the PME printed objects was lower than that of the FFF printed parts based on the print layer uniformity and structure. Further, due to the poorer print resolution and inherent inconsistent build material feed of the PME, the bulk tensile strength and Young's moduli of the objects printed by PME were lower and more inconsistent (49.2 ± 10.7 MPa and 1620 ± 375 MPa, respectively) than those of FFF printed objects (57.7 ± 2.31 MPa and 2160 ± 179 MPa, respectively). Nevertheless, PME print methods promise an opportunity to provide a platform on which it is possible to rapidly prototype a myriad of thermoplastic materials for 3D printing.
| S-EPMC8074846 | biostudies-literature
Project description:We report the study of the formation of Laser Induced Periodic Surface Structures (LIPSS), with UV femtosecond laser pulses (? = 265 nm), in free-standing films of both Poly(trimethylene terephthalate) (PTT) and the composite PTT/tungsten disulfide inorganic nanotubes (PTT-WS2). We characterized the range of fluences and number of pulses necessary to induce LIPSS formation and measured the topography of the samples by Atomic Force Microscopy, the change in surface energy and contact angle using the sessile drop technique, and the modification in both Young's modulus and adhesion force values with Peak Force-Quantitative Nanomechanical Mapping. LIPSS appeared parallel to the laser polarization with a period close to its wavelength in a narrow fluence and number of pulses regime, with PTT-WS2 needing slightly larger fluence than raw PTT due to its higher crystallinity and heat diffusion. Little change was found in the total surface energy of the samples, but there was a radical increase in the negative polar component (?-). Besides, we measured small variations in the samples Young's modulus after LIPSS formation whereas adhesion is reduced by a factor of four. This reduction, as well as the increase in ?-, is a result of the modification of the surface chemistry, in particular a slight oxidation, during irradiation.
| S-EPMC7284604 | biostudies-literature
Project description:Fabrication of partially biobased poly(trimethylene terephthalate) (PTT) elastomeric blends was done via melt processing. Both natural rubber (NR) and epoxidized NR (ENR) were investigated as impact modifiers at 40 wt % loading to avoid lowering the overall biobased content of the blend system below that of the PTT alone (35% renewable content), along with maleated polybutadiene rubber (MR) and dicumyl peroxide (DCP) as reactive compatibilizers. The compatibility of the blend components was investigated using contact angle, rheometry, and scanning electron microscopy (SEM). The interfacial tensions and work of adhesions indicated that ENR was more miscible than NR in the PTT blend system, which was corroborated by the higher shear viscosity of the ENR blends and strong shear thinning behavior. Additionally, the predictive modeling of viscosity ratios on the elastomer-thermoplastic morphology was found to match the SEM micrographs with the dispersed elastomeric phase within the PTT matrix. The SEM images of the blends also establish that both the compatibilizers reduced the rubber inclusions size, though DCP hampered the impact performance as compared to the MR. In the presence of the MR, there was an increased cross-linking and observed variation in the Fourier transform infrared peaks demonstrating chemical interactions between the maleic anhydride groups with the PTT that allowed for the impact strength to reach 137 J·m-1 or 4.5 times that of the neat PTT, with the modulus of toughness increased by 82% and an elongation at yield of 50% because of the flexibility and amorphous nature of the rubber constituent.
| S-EPMC6644667 | biostudies-literature
Project description:Although extrusion-based three-dimensional (EB-3D) printing technique has been widely used in the complex fabrication of bone tissue-engineered scaffolds, a natural bone-like radial-gradient scaffold by this processing method is of huge challenge and still unmet. Inspired by a typical fractal structure of Koch snowflake, for the first time, a fractal-like porous scaffold with a controllable hierarchical gradient in the radial direction is presented via fractal design and then implemented by EB-3D printing. This radial-gradient structure successfully mimics the radially gradual decrease in porosity of natural bone from cancellous bone to cortical bone. First, we create a design-to-fabrication workflow with embedding the graded data on basis of fractal design into digital processing to instruct the extrusion process of fractal-like scaffolds. Further, by a combination of suitable extruded inks, a series of bone-mimicking scaffolds with a 3-iteration fractal-like structure are fabricated to demonstrate their superiority, including radial porosity, mechanical property, and permeability. This study showcases a robust strategy to overcome the limitations of conventional EB-3D printers for the design and fabrication of functionally graded scaffolds, showing great potential in bone tissue engineering.
| S-EPMC8637129 | biostudies-literature