Browse
Submit Data
Databases
API
Help

Dataset Information

27 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Field-emission electron gun for a MEMS electron microscope.

ABSTRACT: This article presents a field-emission electron gun intended for use in a MEMS (microelectromechanical system) electron microscope. Its fabrication process follows the technology of a miniature device under development built from silicon electrodes and glass spacers. The electron gun contains a silicon cathode with a single very sharp protrusion and a bundle of disordered CNTs deposited on its end (called a sharp silicon/CNT cathode). It was tested in diode and triode configurations. For the diode configuration, a low threshold voltage <1000 V and a high emission current that reached 90 µA were obtained. After 30 min of operation at 900 V, the emission current decreased to 1.6 µA and was stable for at least 40 min, with RMS fluctuation in the anode current lower than 10%. The electron beam spot of the source was observed on the phosphor screen. In the diode configuration, the spot size was the same as the emission area (~10 µm), which is a satisfactory result. In the triode configuration, an extraction electrode (gate) control function was reported. The gate limited the emission current and elongated the lifetime of the gun when the current limit was set. Moreover, the electron beam current fluctuations at the anode could be reduced to ~1% by using a feedback loop circuit that controls the gate voltage, regulating the anode current. The developed sharp silicon/CNT cathodes were used to test the MEMS electron source demonstrator, a key component of the MEMS electron microscope, operating under atmospheric pressure conditions. Cathodoluminescence of the phosphor layer (ZnS:Ag) deposited on the thin silicon nitride membrane (anode) was observed.

SUBMITTER: Krysztof M

PROVIDER: S-EPMC8433145 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Field-Emission Scanning Electron Microscope as a Tool for Large-Area and Large-Volume Ultrastructural Studies.

Project description:The development of field-emission scanning electron microscopes for high-resolution imaging at very low acceleration voltages and equipped with highly sensitive detectors of backscattered electrons (BSE) has enabled transmission electron microscopy (TEM)-like imaging of the cut surfaces of tissue blocks, which are impermeable to the electron beam, or tissue sections mounted on the solid substrates. This has resulted in the development of methods that simplify and accelerate ultrastructural studies of large areas and volumes of biological samples. This article provides an overview of these methods, including their advantages and disadvantages. The imaging of large sample areas can be performed using two methods based on the detection of transmitted electrons or BSE. Effective imaging using BSE requires special fixation and en bloc contrasting of samples. BSE imaging has resulted in the development of volume imaging techniques, including array tomography (AT) and serial block-face imaging (SBF-SEM). In AT, serial ultrathin sections are collected manually on a solid substrate such as a glass and silicon wafer or automatically on a tape using a special ultramicrotome. The imaging of serial sections is used to obtain three-dimensional (3D) information. SBF-SEM is based on removing the top layer of a resin-embedded sample using an ultramicrotome inside the SEM specimen chamber and then imaging the exposed surface with a BSE detector. The steps of cutting and imaging the resin block are repeated hundreds or thousands of times to obtain a z-stack for 3D analyses.

| S-EPMC8698110 | biostudies-literature

Handheld line-scanned dual-axis confocal microscope with pistoned MEMS actuation for flat-field fluorescence imaging.

Project description:A handheld line-scanned dual-axis confocal (LS-DAC) microscope has been developed for high-speed (16 frames/s) fluorescence imaging of tissues with sub-nuclear resolution. This is the first miniature fluorescence LS-DAC system that has been fully packaged for handheld clinical use on patients. A novel micro-electro-mechanical system scanning mechanism, with synchronized tilting and pistoning, is used to achieve flat-field en face imaging. We show that this facilitates video mosaicking to generate images that sample an extended lateral field of view.

| S-EPMC7723749 | biostudies-literature

Efficacy of ultrasonics and Er,Cr:YSGG laser on root surface calculus removal: A comparative in vitro field emission scanning electron microscope study.

Project description:BackgroundScaling and root planing (SRP) is an inevitable primary step in non-surgical periodontal therapy. Debridement carried out with manual instruments and ultrasonics results in the removal of tooth structure. Current research revolves around laser as an efficient adjunct to SRP. This study evaluated and compared the effectiveness of root surface calculus removal between ultrasonics and Er,Cr:YSGG laser.MethodsTwenty-eight single-rooted teeth extracted due to periodontal disease were selected for the study. The specimens were randomly assigned to two groups (n=14). Group I underwent ultrasonic instrumentation using a piezo ultrasonic scaler, and group II was subjected to laser instrumentation using Er,Cr:YSGG laser (Waterlase). The specimens were processed, fixed, viewed under a field emission scanning electron microscope and evaluated using the remaining calculus index (RCI) and loss of tooth substance index (LTSI).ResultsUltrasonics-treated specimens revealed more remaining calculus (1.57±0.65) and lost tooth substance (1.71±0.61) compared to the Er,Cr:YSGG laser-treated specimens, with significantly lower RCI (0.71±0.61) and LTSI (1.00±0.56). There was a statistically significant difference (P<0.05) in the efficacy of root surface calculus removal between the two groups.ConclusionCompared to ultrasonics, Er,Cr:YSGG laser demonstrated superior results by causing precise removal of root surface calculus without significantly affecting tooth structure and aiding in new attachment.

| S-EPMC11252148 | biostudies-literature

Subcycle surface electron emission driven by strong-field terahertz waveforms.

Project description:The advent of intense terahertz (THz) sources opened a new era when the demonstration of the acceleration and manipulation of free electrons by THz pulses became within reach. THz-field-driven electron emission was predicted to be confined to a single burst due to the single-cycle waveform. Here we demonstrate the confinement of single-cycle THz-waveform-driven electron emission to one of the two half cycles from a solid surface emitter. Either the leading or the trailing half cycle was active, controlled by reversing the field polarity. THz-driven single-burst surface electron emission sources, which do not rely on field-enhancement structures, will impact the development of THz-powered electron acceleration and manipulation devices, all-THz compact electron sources, THz waveguides and telecommunication, THz-field-based measurement techniques and solid-state devices.

| S-EPMC10584819 | biostudies-literature

Field Ion Emission in an Atom Probe Microscope Triggered by Femtosecond-Pulsed Coherent Extreme Ultraviolet Light.

Project description:This paper describes initial experimental results from an extreme ultraviolet (EUV) radiation-pulsed atom probe microscope. Femtosecond-pulsed coherent EUV radiation of 29.6 nm wavelength (41.85 eV photon energy), obtained through high harmonic generation in an Ar-filled hollow capillary waveguide, successfully triggered controlled field ion emission from the apex of amorphous SiO2 specimens. The calculated composition is stoichiometric within the error of the measurement and effectively invariant of the specimen base temperature in the range of 25 K to 150 K. Photon energies available in the EUV band are significantly higher than those currently used in the state-of-the-art near-ultraviolet laser-pulsed atom probe, which enables the possibility of additional ionization and desorption pathways. Pulsed coherent EUV light is a new and potential alternative to near-ultraviolet radiation for atom probe tomography.

| S-EPMC7195254 | biostudies-literature

Resonant Tunneling Induced Enhancement of Electron Field Emission by Ultra-Thin Coatings.

Project description:The emission of electrons from the surface of a material into vacuum depends strongly on the material's work function, temperature, and the intensity of electric field. The combined effects of these give rise to a multitude of related phenomena, including Fowler-Nordheim tunneling and Schottky emission, which, in turn, enable several families of devices, ranging from vacuum tubes, to Schottky diodes, and thermionic energy converters. More recently, nanomembrane-based detectors have found applications in high-resolution mass spectrometry measurements in proteomics. Progress in all the aforementioned applications critically depends on discovering materials with effective low surface work functions. We show that a few atomic layer deposition (ALD) cycles of zinc oxide onto suspended diamond nanomembranes, strongly reduces the threshold voltage for the onset of electron field emission which is captured by resonant tunneling from the ZnO layer. Solving the Schroedinger equation, we obtain an electrical field- and thickness-dependent population of the lowest few subbands in the thin ZnO layer, which results in a minimum in the threshold voltage at a thickness of 1.08 nm being in agreement with the experimentally determined value. We conclude that resonant tunneling enables cost-effective ALD coatings that lower the effective work function and enhance field emission from the device.

| S-EPMC6497713 | biostudies-literature

MEMS-in-the-lens architecture for a miniature high-NA laser scanning microscope.

Project description:Laser scanning microscopes can be miniaturized for in vivo imaging by substituting optical microelectromechanical system (MEMS) devices in place of larger components. The emergence of multifunctional active optical devices can support further miniaturization beyond direct component replacement because those active devices enable diffraction-limited performance using simpler optical system designs. In this paper, we propose a catadioptric microscope objective lens that features an integrated MEMS device for performing biaxial scanning, axial focus adjustment, and control of spherical aberration. The MEMS-in-the-lens architecture incorporates a reflective MEMS scanner between a low-numerical-aperture back lens group and an aplanatic hyperhemisphere front refractive element to support high-numerical-aperture imaging. We implemented this new optical system using a recently developed hybrid polymer/silicon MEMS three-dimensional scan mirror that features an annular aperture that allows it to be coaxially aligned within the objective lens without the need for a beam splitter. The optical performance of the active catadioptric system is simulated and imaging of hard targets and human cheek cells is demonstrated with a confocal microscope that is based on the new objective lens design.

| S-EPMC6592906 | biostudies-literature

Field-portable lensfree tomographic microscope.

Project description:We present a field-portable lensfree tomographic microscope, which can achieve sectional imaging of a large volume (?20 mm(3)) on a chip with an axial resolution of <7 ?m. In this compact tomographic imaging platform (weighing only ?110 grams), 24 light-emitting diodes (LEDs) that are each butt-coupled to a fibre-optic waveguide are controlled through a cost-effective micro-processor to sequentially illuminate the sample from different angles to record lensfree holograms of the sample that is placed on the top of a digital sensor array. In order to generate pixel super-resolved (SR) lensfree holograms and hence digitally improve the achievable lateral resolution, multiple sub-pixel shifted holograms are recorded at each illumination angle by electromagnetically actuating the fibre-optic waveguides using compact coils and magnets. These SR projection holograms obtained over an angular range of ±50° are rapidly reconstructed to yield projection images of the sample, which can then be back-projected to compute tomograms of the objects on the sensor-chip. The performance of this compact and light-weight lensfree tomographic microscope is validated by imaging micro-beads of different dimensions as well as a Hymenolepis nana egg, which is an infectious parasitic flatworm. Achieving a decent three-dimensional spatial resolution, this field-portable on-chip optical tomographic microscope might provide a useful toolset for telemedicine and high-throughput imaging applications in resource-poor settings.

| S-EPMC3154753 | biostudies-literature

A new method for assessment of nickel-titanium endodontic instrument surface roughness using field emission scanning electronic microscope.

Project description:BACKGROUND:To introduce a new method for measurement of surface roughness of the endodontic instrument, before and after instrumentation, using the Field Emission Scanning Electronic Microscope (FE-SEM) combined with the ImageJ software. METHODS:Twenty J-shape resin blocks were divided into two groups, ten blocks of each group. Simulated root canal inside the resin block was 16?mm length, 600 angle of curvature, and radius of 4.5?mm. Ten WaveOne Gold Primary and 10 Reciproc Blue R25 instruments were used for root canal instrumentation. The instruments were scanned before and after instrumentation with special molds made to ensure the same areas at the point located 3?mm from the tips of the instruments using the FE-SEM. These scanned images were analyzed using the ImageJ. The arithmetical mean roughness (Ra), root mean square roughness (Rq), and the average distance between the highest peak and lowest valley in each sampling length (Rz) were calculated by ImageJ for quantitative analyses. The paired-t test was performed to analyze the data using the SPSS 22.0 at the significance of .05. RESULTS:Almost all surface roughness values were decreased. However, these decreases were not statistically significant (P?>?.05). CONCLUSIONS:The FE-SEM combined with the ImageJ was the reliable and appropriate modality for measurement surface roughness of instruments.

| S-EPMC7461342 | biostudies-literature

MEMS-based handheld confocal microscope for in-vivo skin imaging.

Project description:This paper describes a handheld laser scanning confocal microscope for skin microscopy. Beam scanning is accomplished with an electromagnetic MEMS bi-axial micromirror developed for pico projector applications, providing 800 x 600 (SVGA) resolution at 56 frames per second. The design uses commercial objective lenses with an optional hemisphere front lens, operating with a range of numerical aperture from NA=0.35 to NA=1.1 and corresponding diagonal field of view ranging from 653 microm to 216 microm. Using NA=1.1 and a laser wavelength of 830 nm we measured the axial response to be 1.14 mum full width at half maximum, with a corresponding 10%-90% lateral edge response of 0.39 mum. Image examples showing both epidermal and dermal features including capillary blood flow are provided. These images represent the highest resolution and frame rate yet achieved for tissue imaging with a MEMS bi-axial scan mirror.

| S-EPMC3378354 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data