Browse
Submit Data
Databases
API
Help

Dataset Information

21 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Peculiar Porous Aluminum Oxide Films Produced via Electrochemical Anodizing in Malonic Acid Solution with Arsenazo-I Additive.

ABSTRACT: The influence of arsenazo-I additive on electrochemical anodizing of pure aluminum foil in malonic acid was studied. Aluminum dissolution increased with increasing arsenazo-I concentration. The addition of arsenazo-I also led to an increase in the volume expansion factor up to 2.3 due to the incorporation of organic compounds and an increased number of hydroxyl groups in the porous aluminum oxide film. At a current density of 15 mA·cm^-2 and an arsenazo-I concentration 3.5 g·L^-1, the carbon content in the anodic alumina of 49 at. % was achieved. An increase in the current density and concentration of arsenazo-I caused the formation of an arsenic-containing compound with the formula Na_1,5Al₂(OH)_4,5(AsO₄)₃·7H₂O in the porous aluminum oxide film phase. These film modifications cause a higher number of defects and, thus, increase the ionic conductivity, leading to a reduced electric field in galvanostatic anodizing tests. A self-adjusting growth mechanism, which leads to a higher degree of self-ordering in the arsenazo-free electrolyte, is not operative under the same conditions when arsenazo-I is added. Instead, a dielectric breakdown mechanism was observed, which caused the disordered porous aluminum oxide film structure.

SUBMITTER: Poznyak A

PROVIDER: S-EPMC8433957 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Porous Alumina Films Fabricated by Reduced Temperature Sulfuric Acid Anodizing: Morphology, Composition and Volumetric Growth.

Project description:The volumetric growth, composition, and morphology of porous alumina films fabricated by reduced temperature 280 K galvanostatic anodizing of aluminum foil in 0.4, 1.0, and 2.0 M aqueous sulfuric acid with 0.5-10 mA·cm-2 current densities were investigated. It appeared that an increase in the solution concentration from 0.4 to 2 M has no significant effect on the anodizing rate, but leads to an increase in the porous alumina film growth. The volumetric growth coefficient increases from 1.26 to 1.67 with increasing current density from 0.5 to 10 mA·cm-2 and decreases with increasing solution concentration from 0.4 to 2.0 M. In addition, in the anodized samples, metallic aluminum phases are identified, and a tendency towards a decrease in the aluminum content with an increase in solution concentration is observed. Anodizing at 0.5 mA·cm-2 in 2.0 M sulfuric acid leads to formation of a non-typical nanostructured porous alumina film, consisting of ordered hemispheres containing radially diverging pores.

| S-EPMC7915223 | biostudies-literature

Vertical Etching of Scandium Aluminum Nitride Thin Films Using TMAH Solution.

Project description:A wide bandgap, an enhanced piezoelectric coefficient, and low dielectric permittivity are some of the outstanding properties that have made ScxAl1-xN a promising material in numerous MEMS and optoelectronics applications. One of the substantial challenges of fabricating ScxAl1-xN devices is its difficulty in etching, specifically with higher scandium concentration. In this work, we have developed an experimental approach with high temperature annealing followed by a wet etching process using tetramethyl ammonium hydroxide (TMAH), which maintains etching uniformity across various Sc compositions. The experimental results of etching approximately 730 nm of ScxAl1-xN (x = 0.125, 0.20, 0.40) thin films show that the etch rate decreases with increasing scandium content. Nevertheless, sidewall verticality of 85°~90° (±0.2°) was maintained for all Sc compositions. Based on these experimental outcomes, it is anticipated that this etching procedure will be advantageous in the fabrication of acoustic, photonic, and piezoelectric devices.

| S-EPMC9863442 | biostudies-literature

Porous Aluminum Oxide and Magnesium Oxide Films Using Organic Hydrogels as Structure Matrices.

Project description:We describe the synthesis of mesoporous Al?O? and MgO layers on silicon wafer substrates by using poly(dimethylacrylamide) hydrogels as porogenic matrices. Hydrogel films are prepared by spreading the polymer through spin-coating, followed by photo-cross-linking and anchoring to the substrate surface. The metal oxides are obtained by swelling the hydrogels in the respective metal nitrate solutions and subsequent thermal conversion. Combustion of the hydrogel results in mesoporous metal oxide layers with thicknesses in the ?m range and high specific surface areas up to 558 m²?g-1. Materials are characterized by SEM, FIB ablation, EDX, and Kr physisorption porosimetry.

| S-EPMC5923516 | biostudies-literature

Additive Blending Effects on PEDOT:PSS Composite Films for Wearable Organic Electrochemical Transistors.

Project description:Organic electrochemical transistors (OECTs) employing conductive polymers (CPs) have gained remarkable prominence and have undergone extensive advancements in wearable and implantable bioelectronic applications in recent years. Among the diverse arrays of CPs, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a common choice for the active-layer channel in p-type OECTs, showing a remarkably high transconductance for the high amplification of signals in biosensing applications. This investigation focuses on the novel engineering of PEDOT:PSS composite materials by seamlessly integrating several additives, namely, dimethyl sulfoxide (DMSO), (3-glycidyloxypropyl)trimethoxysilane (GOPS), and a nonionic fluorosurfactant (NIFS), to fine-tune their electrical conductivity, self-healing capability, and stretchability. To elucidate the intricate influences of the DMSO, GOPS, and NIFS additives on the formation of PEDOT:PSS composite films, theoretical calculations were performed, encompassing the solubility parameters and surface energies of the constituent components of the NIFS, PEDOT, PSS, and PSS-GOPS polymers. Furthermore, we conducted a comprehensive array of material analyses, which reveal the intricacies of the phase separation phenomenon and its interaction with the materials' characteristics. Our research identified the optimal composition for the PEDOT:PSS composite films, characterized by outstanding self-healing and stretchable capabilities. This composition has proven to be highly effective for constructing an active-layer channel in the form of OECT-based biosensors fabricated onto polydimethylsiloxane substrates for detecting dopamine. Overall, these findings represent significant progress in the application of PEDOT:PSS composite films in wearable bioelectronics and pave the way for the development of state-of-the-art biosensing technologies.

| S-EPMC10958448 | biostudies-literature

Facile Fabrication of Porous Conductive Thermoplastic Polyurethane Nanocomposite Films via Solution Casting.

Project description:Porous conductive polymers are one of important materials, featuring lightweight, large specific surface area and high porosity. Non-solvent induced phase separation is widely employed to prepare porous polymer sheet materials. Through utilizing water vapor in ambient environment as the non-solvent, a facile approach was developed to produce porous conductive polymer nanocomposites using the conventional solution-casting method. Without using any non-solvent liquids, porous carbon nanofiber/thermoplastic polyurethane (CNF/TPU) nanocomposites were prepared directly by solution casting of their dimethylformamide (DMF) solutions under ambient conditions. The strength of the CNF framework played a key role in preventing the collapse of pores during DMF evaporation. The dependence of porous structures on CNF loading was studied by scanning electron microscopy and porosity measurement. The influence of CNF loading on the mechanical properties, electrical conductivity and piezoresistive behavior was explored.

| S-EPMC5727098 | biostudies-literature

Aluminum with dispersed nanoparticles by laser additive manufacturing.

Project description:While laser-printed metals do not tend to match the mechanical properties and thermal stability of conventionally-processed metals, incorporating and dispersing nanoparticles in them should enhance their performance. However, this remains difficult to do during laser additive manufacturing. Here, we show that aluminum reinforced by nanoparticles can be deposited layer-by-layer via laser melting of nanocomposite powders, which enhance the laser absorption by almost one order of magnitude compared to pure aluminum powders. The laser printed nanocomposite delivers a yield strength of up to 1000?MPa, plasticity over 10%, and Young's modulus of approximately 200?GPa, offering one of the highest specific Young's modulus and specific yield strengths among structural metals, as well as an improved specific strength and thermal stability up to 400?°C compared to other aluminum-based materials. The improved performance is attributed to a high density of well-dispersed nanoparticles, strong interfacial bonding between nanoparticles and Al matrix, and ultrafine grain sizes.

| S-EPMC6739343 | biostudies-literature

Electrochemical and computational estimations of cephalosporin drugs as eco-friendly and efficient corrosion inhibitors for aluminum in alkaline solution.

Project description:In this study, the anionic state of Ceftriaxone sodium (Cefx) and Ceftazidime (Cefz) medication corrosion inhibition capabilities for Al in 0.1 M NaOH solution are explored using various electrochemical analyses. Furthermore, the morphological structure and surface chemical composition of the impact of these drugs on the Al substrate in NaOH are investigated. For the prediction and analysis of interactions between molecule structure and inhibition efficiency, quantum chemical calculations (QC), Monte Carlo simulations (MC), and molecular dynamics (MD) simulations (MD) are performed. The electrochemical findings reveal that the inhibitory effectiveness increases with increasing drug concentrations and declines with rising temperature, reaching a maximum value of 78.4% for 300 ppm Cefx while 59.5% for 300 ppm Cefz at 293 K, implying that Cefx outperforms for Cefz. In addition, the studied drugs act as cathodic inhibitors, and their adsorption is spontaneous and mixed type adsorption in its nature that obeys Freundlich isotherm for Cefz while Temkin isotherm is the best-fitted one for Cefx. Surface analysis and wettability measurements imply that Cefx and Cefz shield the Al against corrosion by surface adsorption and generating a protective hydrophobic film. Thermodynamic activation parameters in the absence and presence of 300 ppm of the studied drugs are calculated and discussed. The energies of the border molecular orbitals and computed molecular parameters for the investigated drugs revealed that anionic Cefx is more readily adsorbed on the Al surface than Cefz. This finding is validated further using MC and MD simulations. Overall, the proposed cephalosporin drugs delivered a cost-effective and facile approach for boosting the efficiency of corrosion inhibitors for Al under aggressive conditions.

| S-EPMC9349255 | biostudies-literature

Self-ordered nanospike porous alumina fabricated under a new regime by an anodizing process in alkaline media.

Project description:High-aspect ratio ordered nanomaterial arrays exhibit several unique physicochemical and optical properties. Porous anodic aluminum oxide (AAO) is one of the most typical ordered porous structures and can be easily fabricated by applying an electrochemical anodizing process to Al. However, the dimensional and structural controllability of conventional porous AAOs is limited to a narrow range because there are only a few electrolytes that work in this process. Here, we provide a novel anodizing method using an alkaline electrolyte, sodium tetraborate (Na2B4O7), for the fabrication of a high-aspect ratio, self-ordered nanospike porous AAO structure. This self-ordered porous AAO structure possesses a wide range of the interpore distance under a new anodizing regime, and highly ordered porous AAO structures can be fabricated using pre-nanotexturing of Al. The vertical pore walls of porous AAOs have unique nanospikes measuring several tens of nanometers in periodicity, and we demonstrate that AAO can be used as a template for the fabrication of nanomaterials with a large surface area. We also reveal that stable anodizing without the occurrence of oxide burning and the subsequent formation of uniform self-ordered AAO structures can be achieved on complicated three-dimensional substrates.

| S-EPMC8012646 | biostudies-literature

Inducing molecular orientation in solution-processed thin films of fluorene-bithiophene-based copolymer: thermal annealing <i>vs.</i> solvent additive.

Project description:A deep understanding of the factors influencing the morphology of thin films based on conjugated polymers is essential to boost their performance in optoelectronic devices. Herein, we investigated the electronic structure and morphology of thin films of the copolymer poly(9,9-dioctyl-fluorenyl-co-bithiophene) (F8T2) in its pristine form as well as samples processed with the solvent additive 1,8-diiodooctane (DIO) or post-processed through thermal annealing treatment. Measurements were carried out using angle-resolved S K-edge NEXAFS (near-edge X-ray absorption fine structure) in total electron yield (TEY) and fluorescence yield (FY) detection modes. Two main transitions were observed at the S 1s NEXAFS spectra: S 1s → π* and S 1s → σ* (S-C). The observed dichroism pointed to a face-on orientation of the conjugated backbone, which was significantly increased for F8T2 films processed with DIO. Resonant Auger decay spectra were obtained and analyzed using the core-hole clock (CHC) method. An enhancement in the charge transfer process was observed for thermally annealed films, especially for samples processed with DIO, corresponding to an increase in film ordering. Furthermore, the investigated films were characterized using X-ray photoelectron spectroscopy, attesting to the presence of the thiophene unit in the samples and demonstrating that some of its sulfur atoms were positively polarized in the F8T2 films. All these experimental findings were compared with molecular dynamics (MD) simulations of film evaporation with and without DIO. The use of MD, together with mathematical modeling, was able to explain the major effects found in the experiments, including the polarization of sulfur atoms. The simultaneous use of powerful spectroscopic techniques and theoretical methods shed light on key aspects linking film morphology with fabrication procedures.

| S-EPMC10945741 | biostudies-literature

Fluorophore-Induced Plasmonic Current Generation from Aluminum Nanoparticle Films.

Project description:In this paper we demonstrate fluorophore induced plasmonic current (FIPC) from aluminum nanoparticle films. It has been previously shown that near-field excited fluorophores are able to plasmonically couple with metal nanoparticle films (MNF's) and induce surface plasmons, which in turn leads to a direct measurable electrical current through the MNF. These currents have been detected and quantified in noble metal MNF's, however due to future envisioned cost considerations there has been a push to adapt FIPC for use with less expensive metals. Subsequently, we observe that plasmonic aluminum films are able to produce these current changes when in close proximity to excited fluorophores, and the magnitude of the current changes are respective to the magnitude of the extinction coefficients of the fluorophores themselves. These findings also further support recent literature reports showing the inverse relationship between metal-enhanced fluorescence (MEF) and FIPC.

| S-EPMC10723758 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data