Field monitoring data on a residential exhaust air heat pump system (air-to-air heat pump).
Ontology highlight
ABSTRACT:
SUBMITTER: Shirani A
PROVIDER: S-EPMC8473652 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Exhaust air heat recovery is of great significance for building energy conservation. Since passive heat recovery systems use temperature or enthalpy difference between outdoor air and indoor air to drive the system, the temperature of fresh air supply cannot meet indoor requirements and the exhaust heat is not fully recovered. In this study, a solar-driven exhaust air thermoelectric heat pump recovery (SDEATHP) system is tested and evaluated for its ability to recover thermal energy from exhaust air to cool or heat fresh air. An experimental platform was established to test its performance. Results show that the SDEATHP system can obtain higher fresh air supply temperature in winter and lower fresh air supply temperature in summer. The system requires only 3.12?W of power for the fans, and the average relative cooling coefficient in summer and the average relative heating coefficient can reach 50.6 and 57.9, respectively. The optimal operating current and voltage of TE modules and photovoltaic system is analyzed, and then the number and types of electrical connections for the TE modules in SDEATHP system are discussed. The SDEATHP system provides a new method for building energy recovery and fresh air supply.
| S-EPMC7126626 | biostudies-literature
Project description:BackgroundIndustrialization and urbanization, while associated with increased productivity, are also potential causes of increased air pollution. Urban air quality has the potential to affect the health and wellbeing of residents of urban areas.ObjectivesThe present study investigated the levels of air pollutants around residential areas and transport sector locations (TSLs) in Lagos, Nigeria. Residential areas were defined as areas around inner streets and living quarters, while TSLs included busy roads, dual carriage roads, bus stops and major car parks in the Yaba Local Council Development Area of Lagos Mainland, Lagos, Nigeria.MethodsAir quality parameters were assessed in situ using calibrated hand-held devices at selected residential and TSLs. Each sampling location was geo-referenced and concentrations of the various parameters were used to plot distribution maps.ResultsThe findings from the monitoring exercise showed that levels of the measured air pollutants: carbon monoxide (CO), particulate matter (PM10 and PM2.5), sulphur dioxide (SO2), noise, temperature and humidity were within the ranges of 1.00 - 6.0 5.97 ppm, 43.345.2 - 127.2159.7 μg/m3, 20.3 23.25 - 69.058.16 μg/m3, 0.0 0 - 0.20.17 ppm, 47.7 50 - 65 70.1 dB, 26.2227.2 - 35.536.7°C and 57.0157.6 - 91.8492.3%, respectively, around residential areas. Values of the measured air pollutants at the TSLs ranged as follows: 2.011.0 - 5.397.7 ppm, 103.3360.7 - 179.77404.0 μg/m3, 50.2832.3 - 91.01184.0 μg/m3, 0.00 - 0.40 ppm, 64.2153.1 - 71.1376.3 dB, 27.1826.2 -27.9332.6°C and 60.3660.0 - 75.0178.0%, respectively. Hydrogen sulphide (H2S), ammonia (NH3), nitrogen oxide (NO2) were below detection limits in both sampling locations while volatile organic carbons (VOCs) ranged from 0.00 - 0.10 ppm in the TSLs.DiscussionMost assessed air quality parameters were significantly higher around bus stops (P < 0.05), except for CO and humidity. In addition, PM10 and PM2.5 were much higher than the World Health Organization (WHO) guidelines. The results indicated that the quality of air (particulate matter) in the study area was poor, especially in the TSLs.ConclusionsThe Federal Ministry of Environment, through its relevant agencies, must create policies to address urban air pollution, taking into consideration long term exposures and people that are most vulnerable within the population.Competing interestsThe authors declare no competing financial interests.
| S-EPMC6257165 | biostudies-literature
Project description:With electric heat pumps substituting for fossil-fueled alternatives, the temporal variability of their power consumption becomes increasingly important to the electricity system. To easily include this variability in energy system analyses, this paper introduces the "When2Heat" dataset comprising synthetic national time series of both the heat demand and the coefficient of performance (COP) of heat pumps. It covers 16 European countries, includes the years 2008 to 2018, and features an hourly resolution. Demand profiles for space and water heating are computed by combining gas standard load profiles with spatial temperature and wind speed reanalysis data as well as population geodata. COP time series for different heat sources - air, ground, and groundwater - and different heat sinks - floor heating, radiators, and water heating - are calculated based on COP and heating curves using reanalysis temperature data. The dataset, as well as the scripts and input parameters, are publicly available under an open source license on the Open Power System Data platform.
| S-EPMC6773861 | biostudies-literature
Project description:The data presented in this article are the measurement results of an air-to-air enthalpy exchanger and a heat exchanger. Such exchangers are used in ventilation devices. The data include 86 measurement points with different boundary conditions (winter and summer condition). The temperature, the humidity, the volume flow and all relevant pressures and pressure differences are provided. The data are mean values of a steady-state measurement. For more insight and interpretation of the results please see "Effectiveness of a membrane enthalpy heat exchanger" [1].
| S-EPMC6811974 | biostudies-literature
Project description:This study presents a health-centered approach to quantify and compare the chronic harm caused by indoor air contaminants using disability-adjusted life-year (DALY). The aim is to understand the chronic harm caused by airborne contaminants in dwellings and identify the most harmful. Epidemiological and toxicological evidence of population morbidity and mortality is used to determine harm intensities, a metric of chronic harm per unit of contaminant concentration. Uncertainty is evaluated in the concentrations of 45 indoor air contaminants commonly found in dwellings. Chronic harm is estimated from the harm intensities and the concentrations. The most harmful contaminants in dwellings are PM2.5, PM10-2.5, NO2, formaldehyde, radon, and O3, accounting for over 99% of total median harm of 2200 DALYs/105 person/year. The chronic harm caused by all airborne contaminants in dwellings accounts for 7% of the total global burden from all diseases.
| S-EPMC10785761 | biostudies-literature
Project description:The decarbonisation of residential heating is crucial if the net-zero target in the United Kingdom is going to be achieved. This paper describes methods to produce data to quantify the impacts of residential heat decarbonisation on the energy supply infrastructure across England and Wales. For the year 2018, annual heat demand for a range of dwellings was estimated for almost 35,000 local areas (known as Lower Layer Super Output Areas: LSOAs). Energy savings through implementing the potential energy efficiency measures and the indicative costs of the energy efficiency measures were quantified. Profiles were synthesised for heat production and energy demand of selected heating technologies using average daily temperature and data from trial projects. These profiles were created to study the impacts of different types of heating technology in each LSOA under user-defined heat decarbonisation pathways. Data describing the dwelling stock, heating technologies, annual heat demand for each LSOA, indicative costs of energy efficiency improvements for each local authority and the profiles for each technology were created.
| S-EPMC9142590 | biostudies-literature
Project description:This work presents a hardware/software data acquisition system developed for monitoring the temperature in real time of the cells in Air-Cooled Polymer Electrolyte Fuel Cells (AC-PEFC). These fuel cells are of great interest because they can carry out, in a single operation, the processes of oxidation and refrigeration. This allows reduction of weight, volume, cost and complexity of the control system in the AC-PEFC. In this type of PEFC (and in general in any PEFC), the reliable monitoring of temperature along the entire surface of the stack is fundamental, since a suitable temperature and a regular distribution thereof, are key for a better performance of the stack and a longer lifetime under the best operating conditions. The developed data acquisition (DAQ) system can perform non-intrusive temperature measurements of each individual cell of an AC-PEFC stack of any power (from watts to kilowatts). The stack power is related to the temperature gradient; i.e., a higher power corresponds to a higher stack surface, and consequently higher temperature difference between the coldest and the hottest point. The developed DAQ system has been implemented with the low-cost open-source platform Arduino, and it is completed with a modular virtual instrument that has been developed using NI LabVIEW. Temperature vs time evolution of all the cells of an AC-PEFC both together and individually can be registered and supervised. The paper explains comprehensively the developed DAQ system together with experimental results that demonstrate the suitability of the system.
| S-EPMC5539708 | biostudies-other
Project description:We propose a mesoscopic Brownian magneto heat pump made of a single charged Brownian particle that is steered by an external magnetic field. The particle is subjected to two thermal noises from two different heat sources. When confined, the particle performs gyrating motion around a potential energy minimum. We show that such a magneto-gyrator can be operated as both a heat engine and a refrigerator. The maximum power delivered by the engine and the performance of the refrigerator, namely the rate of heat transferred per unit external work, can be tuned and optimised by the applied magnetic field. Further tunability of the key properties of the engine, such as the direction of gyration and the torque exerted by the engine on the confining potential, is obtained by varying the strength and direction of the applied magnetic field. In principle, our predictions can be tested by experiments with colloidal particles and complex plasmas.
| S-EPMC9352690 | biostudies-literature
Project description:The now widespread use of smart heat meters for buildings connected to district heating networks generates data at an unknown extent and temporal resolution. This data encompasses information that enables new data-driven approaches in the building sector. Real-life data of sufficient size and quality are necessary to facilitate the development of such methods, as subsequent analyses typically require a complete equidistant dataset without missing or erroneous values. Thus, this work presents three years (2018-01-03 till 2020-12-31) of screened, interpolated, and imputed data from 3,021 commercial smart heat meters installed in Danish residential buildings. The screening aimed to detect data from not used meters, resolve issues caused by the data storage process and identify erroneous values. Linear interpolation was used to obtain equidistant data. After the screening, 0.3% of the data were missing, which were imputed using a weighted moving average based on a systematic comparison of nine different imputation methods. The original and processed data are published together with the code for data processing ( https://doi.org/10.5281/zenodo.6563114 ).
| S-EPMC9296640 | biostudies-literature
Project description:About 90% of our time is spent indoors where we are exposed to chemical and biological contaminants and possibly to carcinogens. These agents may influence the risk of developing nonspecific respiratory and neurologic symptoms, allergies, asthma and lung cancer. We review the sources, health effects and control strategies for several of these agents. There are conflicting data about indoor allergens. Early exposure may increase or may decrease the risk of future sensitization. Reports of indoor moulds or dampness or both are consistently associated with increased respiratory symptoms but causality has not been established. After cigarette smoking, exposure to environmental tobacco smoke and radon are the most common causes of lung cancer. Homeowners can improve the air quality in their homes, often with relatively simple measures, which should provide health benefits.
| S-EPMC2443227 | biostudies-literature