Dataset Information

Laser-Induced Graphene Heater Pad for De-Icing.

ABSTRACT: The replacement of electro-thermal material in heaters with lighter and easy-to-process materials has been extensively studied. In this study, we demonstrate that laser-induced graphene (LIG) patterns could be a good candidate for the electro-thermal pad. We fabricated LIG heaters with various thermal patterns on the commercial polyimide films according to laser scanning speed using an ultraviolet pulsed laser. We adopted laser direct writing (LDW) to irradiate on the substrates with computer-aided 2D CAD circuit data under ambient conditions. Our highly conductive and flexible heater was investigated by scanning electron microscopy, transmission electron microscopy, Raman spectroscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, X-ray diffraction, and Brunauer-Emmett-Teller. The influence of laser scanning speed was evaluated for electrical properties, thermal performance, and durability. Our LIG heater showed promising characteristics such as high porosity, light weight, and small thickness. Furthermore, they demonstrated a rapid response time, reaching equilibrium in less than 3 s, and achieved temperatures up to 190 °C using relatively low DC voltages of approximately 10 V. Our LIG heater can be utilized for human wearable thermal pads and ice protection for industrial applications.

SUBMITTER: Lee JU

PROVIDER: S-EPMC8619929 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:Realization of graphene-based sensors and electronic devices remains challenging, in part due to integration challenges with current fabrication and manufacturing processes. Thus, scalable methods for in situ fabrication of high-quality graphene-like materials are essential. Low-cost CO2 laser engravers can be used for site-selective conversion of polyimide under ambient conditions to create 3-D, rotationally disordered, few-layer, porous, graphene-like electrodes. However, the influences of non-linear parameter terms and interactions between key parameters on the graphitization process present challenges for rapid, resource-efficient optimization. An iterative optimization strategy was developed to identify promising regions in parameter space for two key parameters, laser power and scan speed, with the goal of optimizing electrode performance while maximizing scan speed and hence fabrication throughput. The strategy employed iterations of Design of Experiments Response Surface (DoE-RS) methods combined with choices of readily measurable parameters to minimize measurement resources and time. The initial DoE-RS experiment set employed visual response parameters, while subsequent iterations used sheet resistance as the optimization parameter. The final model clearly demonstrates that laser graphitization through raster scanning is a highly non-linear process requiring polynomial terms in scan speed and laser power up to fifth order. Two regions of interest in parameter space were identified using this strategy: Region 1 represents the global minimum for sheet resistance for this laser (∼16 Ω/sq), found at a low scan speed (70 mm/s) and a low average power (2.1 W) . Region 2 is a local minimum for sheet resistance (36 Ω/sq), found at higher values for scan speed (340 mm/s) and average power (3.4 W), allowing ∼5-fold reduction in write time. Importantly, these minima do not correspond to constant ratios of average laser power to scan speed. This highlights the benefits of DoE-RS methods in rapid identification of optimum parameter combinations that would be difficult to discover using traditional one-factor-at-a-time optimization. Verification data from Raman spectroscopy showed sharp 2D peaks with mean full-width-at-half-maximum intensity values <80 cm-1 for both regions, consistent with high-quality 3D graphene-like carbon. Graphene-based electrodes fabricated using the parameters from the respective regions yielded similar performance when employed as capacitive humidity sensors with hygroscopic dielectric layers. Devices fabricated using Region 1 parameters (16 Ω/sq) yielded capacitance responses of 0.78 ± 0.04 pF at 0% relative humidity (RH), increasing to 31 ± 7 pF at 85.1% RH. Region 2 devices (36 Ω/sq) showed comparable responses (0.88 ± 0.04 pF at 0% RH, 28 ± 5 pF at 85.1% RH).

Dataset Information

Laser-Induced Graphene Heater Pad for De-Icing.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets