Browse
Submit Data
Databases
API
Help

Dataset Information

17 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Degradation of Minocycline by the Adsorption-Catalysis Multifunctional PVDF-PVP-TiO₂ Membrane: Degradation Kinetics, Photocatalytic Efficiency, and Toxicity of Products.

ABSTRACT: The photocatalytic degradation of minocycline was studied by using polyvinylidene fluoride-polyvinylpyrrolidone-TiO₂ (PVDF-PVP-TiO₂) fiber mats prepared by an electrospinning technology. The influences of the TiO₂ dosage, minocycline concentrations, inorganic anions, pH values, and dissolved organic matter (DOM) concentrations on the degradation kinetics were investigated. A mass of 97% minocycline was degraded in 45 min at 5% TiO₂ dosage. The corresponding decomposition rate constant was 0.069 min^-1. The inorganic anions affected the minocycline decomposition in the order of HCO₃^- > Cl^- > SO₄^2- > NO₃^-, which was confirmed by the results of electron spin resonance (ESR) spectra. The lowest electrical energy per order (E_EO) was 6.5 Wh/L. Over five cycles, there was no change in the photocatalytic performance of the degrading minocycline. Those investigations suggested that effective degradation of minocycline could be reached in the PVDF-PVP-TiO₂ fiber mats with a low energy consumption, good separation and, good recovery. Three photocatalytic decomposition pathways of minocycline were proposed: (i) hydroxyl substitution of the acylamino group; (ii) hydroxyl substitution of the amide group, and (iii) a cleavage of the methyl groups and further oxidation of the amino group by OH. Potential risks caused by TP159 and TP99 should not be ignored, while the TP90 are nontoxic. Tests indicated that the toxicity of the photocatalytic process may be persistent if minocycline and its products were not mineralized completely.

SUBMITTER: Zhou C

PROVIDER: S-EPMC8656511 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Statistical Analysis of Synthesis Parameters to Fabricate PVDF/PVP/TiO2 Membranes via Phase-Inversion with Enhanced Filtration Performance and Photocatalytic Properties.

Project description:Non-solvent induced phase-inversion is one of the most used methods to fabricate membranes. However, there are only a few studies supported by statistical analysis on how the different fabrication conditions affect the formation and performance of membranes. In this paper, a central composite design was employed to analyze how different fabrication conditions affect the pure water flux, pore size, and photocatalytic activity of polyvinylidene fluoride (PVDF) membranes. Polyvinylpyrrolidone (PVP) was used to form pores, and titanium dioxide (TiO2) to ensure the photocatalytic activity of the membranes. The studied bath temperatures (15 to 25 °C) and evaporation times (0 to 60 s) did not significantly affect the pore size and pure water flux of the membranes. The concentration of PVDF (12.5 to 17.5%) affected the viscosity, formation capability, and pore sizes. PVDF at high concentrations resulted in membranes with small pore sizes. PVP affected the pore size and should be used to a limited extent to avoid possible hole formation. TiO2 contents were responsible for the decolorization of a methyl orange solution (10-5 M) up to 90% over the period studied (30 h). A higher content of TiO2 did not increase the decolorization rate. Acidic conditions increased the photocatalytic activity of the TiO2-membranes.

| S-EPMC8747740 | biostudies-literature

Flexible TiO2/PVDF/g-C3N4 Nanocomposite with Excellent Light Photocatalytic Performance.

Project description:As the world faces water shortage and pollution crises, the development of novel visible light photocatalysts to purify water resources is urgently needed. Over the past decades, most of the reported photocatalysts have been in powder or granular forms, creating separation and recycling difficulties. To overcome these challenges, a flexible and recyclable heterostructured TiO2/polyvinylidene fluoride/graphitic carbon nitride (TiO2/PVDF/g-C3N4) composite was developed by combining electrospinning, sintering and hydrothermal methods. In the composite, PVDF was used as a support template for removing and separating the photocatalyst from solution. Compared with pure TiO2, the TiO2/PVDF/g-C3N4 composite exhibited the extended light capture range of TiO2 into the visible light region. The photogenerated carriers were efficiently transferred and separated at the contact interface between TiO2 and g-C3N4 under visible light irradiation, which consequently increased the photocatalytic activity of the photocatalyst. In addition, the flexible composites exhibited excellent self-cleaning properties, and the dye on the photocatalysts was completely degraded by the as-prepared materials. Based on the intrinsic low cost, recyclability, absorption of visible light, facile synthesis, self-cleaning properties and good photocatalytic performances of the composite, the photocatalyst is expected to be used for water treatment.

| S-EPMC7023571 | biostudies-literature

Multifunctional polymer-based nanocomposites for synergistic adsorption and photocatalytic degradation of mixed pollutants in water.

Project description:Water pollution is a growing concern for mankind due to its harmful effects on humans, animals and plants. Usually, several pollutants are present in wastewater. For example, dyes and antibiotics are found in wastewater because of their widespread use in factories and hospitals. However, one single technique, e.g. either adsorption or photocatalysis, cannot easily remove more than one kind of pollutant, especially by using one single material in water. For this reason, here multifunctional iron(ii,iii) oxide/poly(N-isopropylacrylamide-co-methacrylic acid)/silver-titanium dioxide (Fe3O4/P(NIPAM-co-MAA)/Ag-TiO2) nanocomposites were used to remove a mixture of pollutants from water. Specifically, three types of experiments were performed to evaluate the adsorption capacity and photodegradation activity of the nanocomposites towards the dye basic fuchsin (BF) and the antibiotic ciprofloxacin (CIP), which were added sequentially to the nanocomposites dispersion or were concurrently present as a mixture. The results demonstrated that the nanocomposites could adsorb BF, and subsequently photodegrade CIP under visible-light irradiation, if BF was the first added pollutant. As well, the nanocomposites could first degrade CIP under visible-light irradiation, and then adsorb BF if they were initially put in contact with CIP. Finally, the ability of adsorbing BF and photodegrading CIP was confirmed in the co-presence of the two pollutants.

| S-EPMC10929593 | biostudies-literature

Response Surface Methodology: Photocatalytic Degradation Kinetics of Basic Blue 41 Dye Using Activated Carbon with TiO2.

Project description:Water decontamination still remains a major challenge to some developing countries not having centralized wastewater systems. Therefore, this study presents the optimization of photocatalytic degradation of Basic Blue 41 dye in an aqueous medium by an activated carbon (AC)-TiO2 photocatalyst under UV irradiation. The mesoporous AC-TiO2 synthesized by a sonication method was characterized by X-ray diffraction (XRD) and Fourier-transform infrared (FTIR) spectroscopy for crystal phase identification and molecular bond structures, respectively. The efficiency of the AC-TiO2 was evaluated as a function of three input variables viz. catalyst load (2-4 g), reaction time (15-45 min) and pH (6-9) by using Box-Behnken design (BBD) adapted from response surface methodology. Using color and turbidity removal as responses, a 17 run experiment matrix was generated by the BBD to investigate the interaction effects of the three aforementioned input factors. From the results, a reduced quadratic model was generated, which showed good predictability of results agreeable to the experimental data. The analysis of variance (ANOVA), signposted the selected models for color and turbidity, was highly significant (p < 0.05) with coefficients of determination (R2) values of 0.972 and 0.988, respectively. The catalyst load was found as the most significant factor with a high antagonistic impact on the process, whereas the interactive effect of reaction time and pH affected the process positively. At optimal conditions of catalyst load (2.6 g), reaction time (45 min), and pH (6); the desirability of 96% was obtained by a numerical optimization approach representing turbidity removal of 93% and color of 96%.

| S-EPMC7922207 | biostudies-literature

Photocatalytic Degradation of Organic Dye under UV-A Irradiation Using TiO2-Vetiver Multifunctional Nano Particles.

Project description:The properties and photocatalytic performance of anatase nanoparticles of pure TiO₂ and a core-shell structure of TiO₂ on calcined vetiver grass leaves have been compared. Samples were fabricated by sol-gel and heating at 450 °C for 5h.The comparison was based on data for X-ray diffraction(XRD), UV-Vis spectrophotometry, photoluminescence, transmission electron microscopy, specific surface area measurement, pore volume assessment, and methylene blue degradation testing. The results showed that the pure TiO2 consisted of agglomerated equiaxed nanoparticles of individual grain sizes in the range 10-20 nm. In contrast, the TiO₂-vetiver composite exhibited a core-shell structure consisting of a carbonaceous core and TiO₂ shell of thickness 10-15nm. These features influenced the photocatalytic performance in such a way that the lower crosssectional area, greater surface area, and higher pore volume of the TiO₂ shell increased the number of active sites, reduced the charge carrier diffusion distance, and reduced the recombination rate, thereby improving the photocatalytic activity. This improvement derived from morphological characteristics rather than crystallographic, semiconducting, or optical properties. The improved performance of the TiO₂-vetiver core-shell was unexpected since the X-ray diffraction data showed that the crystallinity of the TiO₂ was lower than that of the pure TiO₂. These outcomes are attributed to the reducing effect of the carbon on the TiO₂ during heating, thereby facilitating the formation of oxygen vacancies, which enhance charge separation and hence photocatalysis by TiO₂.

| S-EPMC5459196 | biostudies-other

Aerobic Oil-Phase Cyclic Magnetic Adsorption to Synthesize 1D Fe2O3@TiO2 Nanotube Composites for Enhanced Visible-Light Photocatalytic Degradation.

Project description:In this work, Fe2O3@TiO2 nanostructures with staggered band alignment were newly designed by an aerobic oil-phase cyclic magnetic adsorption method. XRD and TEM analyses were performed to verify the uniform deposition of Fe2O3 nanoparticles on the nanotube inner walls of TiO2. The steady-state degradation experiments exhibited that 1FeTi possessed the most superior performance, which might be ascribable to the satisfying dark adsorption capacity, efficient photocatalytic activity, ease of magnetic separation, and economic efficiency. These results indicated that the deposition of Fe2O3 into TiO2 nanotubes significantly enhanced the activity of Fe2O3, which was mainly ascribed to the Fe2O3-induced formation of staggered iron oxides@TiO2 band alignment and thus efficient separation of h+ and e-. Furthermore, the PL intensity and lifetime of the decay curve were considered as key criterions for the activity's evaluation. Finally, the leaching tests and regeneration experiments were also performed, which illustrated the inhibited photodissolution compared with TiO2/Fe3O4 and stable cycling ability, enabling 1FeTi to be a promising magnetic material for photocatalytic water remediation.

| S-EPMC7408372 | biostudies-literature

Novel TiO2 Nanoparticles/Polysulfone Composite Hollow Microspheres for Photocatalytic Degradation.

Project description:Nanosized titanium oxide (TiO2) material is a promising photocatalyst for the degradation of organic pollutants, whereas the difficulty of its recycling hinders its practical application. Herein, we reported the preparation of a novel titanium oxide/polysulfone (TiNPs/PSF) composite hollow microspheres by the combination of Pickering emulsification and the solvent evaporation technique and their application for the photodegradation of methyl blue (MB). P25 TiO2 nanoparticles dispersed on the surface of PSF microspheres. The porosity, density and photoactivity of the TiNPs/PSF composite microsphere are influenced by the TiO2 loading amount. The composite microsphere showed good methyl blue (MB) removal ability. Compared with TiO2 P25, and PSF, a much higher MB adsorption speed was observed for TiNPs/PSF microspheres benefited from their porous structure and the electrostatic attractions between the MB+ and the negatively charged PSF materials, and showed good degradation efficiency. For TiNPs/PSF composite microsphere with density close to 1, a 100% MB removal (10 mg L-1) within 120 min at a catalyst loading of 2.5 g L-1 can be obtained under both stirring and static condition, due to well dispersing of TiO2 particles on the microsphere surface and its stable suspending in water. For the non-suspended TiNPs/PSF composite microsphere with density bigger than 1, the 100% MB removal can be only obtained under stirring condition. The removal efficiency of MB for the composite microspheres retained 96.5%, even after 20 cycles. Moreover, this composite microsphere also showed high MB removal ability at acidic condition. The high catalysis efficiency, excellent reusability and good stability make this kind of TiNPs/PSF composite microsphere a promising photocatalyst for the water organic pollution treatment.

| S-EPMC7865213 | biostudies-literature

PMMA-TiO2 Fibers for the Photocatalytic Degradation of Water Pollutants.

Project description:Titanium dioxide (TiO2) is a promising photocatalyst that possesses a redox potential suitable for environmental remediation applications. A low photocatalytic yield and high cost have thus far limited the commercial adoption of TiO2-based fixed-bed reactors. One solution is to engineer the physical geometry or chemical composition of the substrate to overcome these limitations. In this work, porous polymethyl methacrylate (PMMA) substrates with immobilized TiO2 nanoparticles in fiber forms were fabricated and analyzed to demonstrate the influence of contaminant transport and light accessibility on the overall photocatalytic performance. The influences of (i) fiber porosity and (ii) fiber architecture on the overall photocatalytic performance were investigated. The porous structure was fabricated using wet phase inversion. The core-shell-structured fibers exhibited much higher mechanical properties than the porous fibers (7.52 GPa vs. non-testability) and maintained the same degradation rates as porous structures (0.059 vs. 0.053/min) in removing methylene blue with comparable specific surface areas. The highest methylene blue (MB) degradation rate (kMB) of 0.116 min-1 was observed due to increases of the exposed surface area, pointing to more efficient photocatalysis by optimizing core-shell dimensions. This research provides an easy-to-manufacture and cost-efficient method for producing PMMA/TiO2 core-shell fibers with a broad application in water treatment, air purification, and volatile sensors.

| S-EPMC7407631 | biostudies-literature

Theoretical investigation on the adsorption configuration and (•)OH-initiated photocatalytic degradation mechanism of typical atmospheric VOCs styrene onto (TiO2)n clusters.

Project description:In this study, the adsorption mechanism and hydroxyl radical ((•)OH)-initiated photocatalytic degradation mechanism of styrene onto different (TiO2)n clusters were investigated using density functional theory. Styrene, a typical model atmospheric volatile organic compound (VOC), was found to be readily adsorbed onto (TiO2)n clusters through its vinyl group with strong chemisorption. This suggests that (TiO2)n clusters (sub 1 nm) are able to effectively adsorb and trap styrene. Adsorbed styrene is then easily attacked by (•)OH to form a series of vinyl-OH-adducts. Conversely, phenyl-OH-adducts and H-abstraction products are very difficult to form in this system. Kinetics calculations using canonical variational transition state theory show that temperature has little effect on the rate constants during photocatalytic degradation process. The presence of TiO2 does not change the degradation mechanism of styrene, but can accelerate its photocatalyic degradation rate, and the rate will increase as TiO2 cluster size increases; as such, the TiO2 nano-clusters catalyst should have the photocatalytic ability to effectively degrade styrene. This theory-based study offers insights into the catalytic effect of TiO2 catalyst and the photocatalytic degradation mechanism of benzene series air pollutants at the molecular level.

| S-EPMC4601031 | biostudies-literature

Photocatalytic Degradation of Selected Pharmaceuticals Using g-C3N4 and TiO2 Nanomaterials.

Project description:Exfoliated graphitic carbon nitride (g-C3N4) and two commercially available nanomaterials from titanium dioxide (P25 and CG300) were tested for the photocatalytic degradation of paracetamol (PAR), ibuprofen (IBU), and diclofenac (DIC). Prior to photocatalytic experiments, the nanomaterials were characterized by common methods, such as X-ray diffraction (XRD), UV-VIS diffuse reflectance spectroscopy (DRS), Fourier transformed infrared spectroscopy in attenuated total reflection mode (FTIR-ATR), transmission electron microscopy (TEM), physisorption of nitrogen, and dynamic vapor adsorption (DVS) of water. The sizes and specific surface area (SSA) of the TiO2 nanoparticles were 6 nm and 300 m2·g-1 for CG300 and 21 nm and 50 m2·g-1 for P25. The SSA of g-C3N4 was 140 m2·g-1. All photocatalytic experiments were performed under UV (368 nm), as well as VIS (446 nm) irradiation. TiO2 P25 was the most active photocatalyst under UV irradiation and g-C3N4 was the most active one under VIS irradiation. Photodegradation yields were evaluated by means of high performance liquid chromatography (HPLC) and reaction intermediates were identified using gas chromatography with mass detection (GC-MS). Paracetamol and ibuprofen were totally removed but the intermediates of diclofenac were observed even after 6 h of irradiation. Some intermediates, such as carbazole-1-acetic acid, 2,6-dichloraniline, and hydroxylated derivates of diclofenac were identified. This study showed that g-C3N4 is a promising photocatalyst for the degradation of pharmaceuticals in an aqueous environment, under visible light.

| S-EPMC6780102 | biostudies-literature