Browse
Submit Data
Databases
API
Help

Dataset Information

24 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Green Synthesis of Nano Zinc Oxide/Nanohydroxyapatite Composites Using Date Palm Pits Extract and Eggshells: Adsorption and Photocatalytic Degradation of Methylene Blue.

ABSTRACT: In this study, zinc oxide nanoparticles (ZnO) and nanohydroxyapatite (NHAP) were prepared in the presence of date palm pits extract (DPPE) and eggshells, respectively. Another four nanocomposites were prepared from ZnO and NHAP in different ratios (ZP13, ZP14, ZP15, and ZP16). DPPE and all nanomaterials were characterized using GC-MS, zeta potentials, particle size distributions, XRD, TEM, EDX, FTIR, and pH_PZC. The characterization techniques confirmed the good distribution of ZnO nanoparticles on the surface of NHAP in the prepared composites. Particles were found to be in the size range of 42.3-66.1 nm. The DPPE analysis confirmed the presence of various natural chemical compounds which act as capping agents for nanoparticles. All the prepared samples were applied in the adsorption and photocatalytic degradation of methylene blue under different conditions. ZP14 exhibited the maximum adsorption capacity (596.1 mg/g) at pH 8, with 1.8 g/L as the adsorbent dosage, after 24 h of shaking time, and the static adsorption kinetic process followed a PSO kinetic model. The photocatalytic activity of ZP14 reached 91% after 100 min of illumination at a lower MB concentration (20 mg/L), at pH 8, using 1.5 g/L as the photocatalyst dosage, at 25 °C. The photocatalytic degradation of MB obeyed the Langmuir-Hinshelwood first-order kinetic model, and the photocatalyst reusability exhibited a slight loss in activity (~4%) after five cycles of application.

SUBMITTER: Elsayed MS

PROVIDER: S-EPMC8746312 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Coupling Adsorption-Photocatalytic Degradation of Methylene Blue and Maxilon Red.

Project description:The MB and MR removal process by two mechanisms of adsorption using rice straw (absence of UV light) and photodegradation on TiO2 surfaces was investigated. MB and MR removal efficiency were further intensified upon the sequential operation of adsorption followed by photocatalytic degradation over TiO2 under visible light irradiation. The TiO2 was used to remove methylene blue (MB) and Maxilon Red (MR) dye from aqueous media by continuous mode at 25 ± 2 °C, at pH 6.8 ± 0.2. Photo-illumination study revealed 75.81 and 65.51% MB and MR removal with the dose of 1 g/L TiO2 with an initial concentration of 5 mg/L within 120 min. This study can be deemed of potential applications for the removal of MB and MR dyes on an industrial level using the synergistic adsorption-photocatalytic oxidation approach. A probable photodegradation mechanism was proposed.

| S-EPMC9270313 | biostudies-literature

Solar Light-Induced Methylene Blue Removal over TiO2/AC Composites and Photocatalytic Regeneration.

Project description:TiO2-containing photocatalysts, which combine TiO2 with carbon-based materials, are promising materials for wastewater treatment due to synergistic photodegradation and adsorption phenomena. In this work, TiO2/AC composites were produced by the in situ immobilization of TiO2 nanoparticles over activated carbon (AC) derived from spent coffee grains, using different TiO2/AC proportions. The TiO2/AC composites were tested as adsorbents (dark) and as photocatalysts in a combined adsorption+photocatalytic process (solar irradiation) for methylene blue (MB) removal from ultrapure water, and from a secondary effluent (SecEf) of an urban wastewater treatment plant. All the materials were characterized by XRD (X-ray powder diffraction), N2 adsorption-desorption isotherms at -196 °C, SEM (scanning electron microscopy), UV-Vis diffuse reflectance, FTIR (Fourier-transform infrared spectroscopy), TPD (temperature programmed desorption), XPS (X-ray photoelectron spectroscopy) and TGA (thermogravimetric analysis). The TiAC60 (60% C) composite presented the lowest band gap (1.84 eV), while, for TiAC29 (29% C), the value was close to that of bare TiO2 (3.18 vs. 3.17 eV). Regardless of the material, the solar irradiation improved the percentage of MB discolouration when compared to adsorption in dark conditions. In the case of simultaneous adsorption+photocatalytic assays performed in ultrapure water, TiAC29 presented the fastest MB removal. Nevertheless, both TiAC29 and TiAC60 led to excellent MB removal percentages (96.1-98.1%). UV-induced photoregeneration was a promising strategy to recover the adsorption capacity of the materials, especially for TiAC60 and AC (>95%). When the assays were performed in SecEf, all the materials promoted discolouration percentages close to those obtained in ultrapure water. The bulk water parameters revealed that TiAC60 allowed the removal of a higher amount of MB, associated with the overall improvement of the SecEf quality.

| S-EPMC8625254 | biostudies-literature

Sustainable oil palm trunk fibre based activated carbon for the adsorption of methylene blue.

Project description:Activated carbon (AC) is becoming the limelight due to its widespread application as an adsorbent for wastewater treatment, gases, and catalysis. However, its high consumption and price have drawn more attention to the sustainable use of natural resources as precursor for AC production. This study focuses on synthesising AC from two types of oil palm trunk (OPT) fibres, a significant agricultural waste products produced by Malaysia's thriving palm oil industries. The BET surface area of about 2057.9 m2 g-1 was achieved by chemical activation with phosphoric acid (H3PO4). The efficiency of the synthesised AC was critically analysed based on the adsorption experiments with methylene blue (MB) by varying several parameters (dosage of adsorbent, pH, initial dye concentration, and temperature of the solution) to elucidate the adsorption mechanism(s). A maximum adsorption capacity of 320.4 mg g-1 at 50 °C was achieved, and the Temkin (r2 = 0.98, 0.95, 0.95) and Langmuir (r2 = 0.94, 0.93, 0.95) isotherm models fitted the adsorption process better than the Freundlich (r2 = 0.95, 0.90, 0.86) model. Besides, the pseudo-second-order model (r2 > 0.90) best described the adsorption process, favouring chemisorption over physisorption. Thermodynamics showed MB adsorption on AC was spontaneous except at the highest dye concentration. It was exothermic at lower dye concentrations (50 and 100 mg L-1) and endothermic at higher ones (300, 500, and 700 mg L-1). In a nutshell, this study reveals that OPT fibre is a promising precursor for synthesising highly porous AC for the adsorption of MB dye.

| S-EPMC10719241 | biostudies-literature

Enhancing the Photocatalytic Degradation of Methylene Blue with Graphene Oxide-Encapsulated g-C3N4/ZnO Ternary Composites

Project description: Not available

| S-EPMC11007858 | biostudies-literature

Treatment of Gaseous Ammonia Emissions Using Date Palm Pits Based Granular Activated Carbon.

Project description:The present work investigated the application of granular activated carbon (GAC) derived from date palm pits (DPP) agricultural waste for treating gaseous ammonia. Respective findings indicate increased breakthrough time (run time at which 5% of influent ammonia is exiting with the effluent gas) with a decrease in influent ammonia and increase in GAC bed depth. At a gas flow rate of 1.1 L/min and GAC column length of 8 cm, the following breakthrough trend was noted: 1295 min (2.5 ppmv) > 712 min (5 ppmv) > 532 min (7.5 ppmv). A qualitatively similar trend was also noted for the exhaustion time results (run time at which 95% of influent ammonia is exiting with the effluent gas). The Fourier Transform Infrared Spectroscopy (FTIR) findings for the produced GAC indicated some salient functional groups at the produced GAC surface including O-H, C-H, C-O, and S=O groups. Ammonia adsorption was suggested to result from its interaction with the respective surface functional groups via different mechanisms. Comparison with a commercial GAC showed the date palm pits based GAC to be having slightly higher breakthrough and exhaustion capacity.

| S-EPMC7084576 | biostudies-literature

Porous zinc-discs as nanocatalysts for methylene blue dye treatment in water: sensing, adsorption and photocatalytic degradation.

Project description:This paper reports a zinc derived (ZD) porous nanosystem that has been used for selective sensing, adsorption, and photocatalytic degradation of the known hazardous dye, Methylene blue (MB). Using zinc nitrate and 2-aminoterphthalic acid as precursors, the synthesis has been optimized to yield disc-shaped nanoparticles. This luminescent ZD nanoparticles exhibit absorption and emission wavelengths of 328 nm and 427 nm, respectively at an excitation wavelength of 330 nm. In the presence of MB, there is a sharp decrease in the photoluminescence emission intensity of ZD nanoparticles. The detection limit, quenching constant and the binding constant of ZD nanoparticles with MB are found to be 0.31 × 10-9 M, 3.30 × 106 M-1 and 2.27 × 106 M-1 respectively. The impact of contact time, initial MB concentration, and pH on the adsorption process were investigated. The equilibrium data fit well with the Langmuir adsorption isotherm model (R 2 = 0.989) and superlatively fitted to the pseudo-second-order rate model (rate constant: 0.00011 g mg-1 min-1; adsorption capacity (q e, calc.): 386.1 mg g-1; R 2: 0.990). Further, the MB dye degradation was performed under ultra-violet irradiation and ∼95% MB degradation was achieved within 70 min. The experimental data are well fitted to the pseudo-first order kinetics (R 2: 0.99; rate constant: 0.015 min-1). These disc shaped ZD nanoparticles can not only facilitate the detection, but also the adsorption and photocatalytic degradation of MB, which can be further processed for environmental remediation applications.

| S-EPMC9728022 | biostudies-literature

Effective photocatalytic degradation and physical adsorption of methylene blue using cellulose/GO/TiO<sub>2</sub> hydrogels.

Project description:Environmentally friendly cellulose/GO/TiO2 hydrogel photocatalyst has been successfully fabricated via a green, simple, and one-step method and evaluated as the photocatalyst and adsorbent for the removal of methylene blue (MB). The XRD and FTIR analysis suggested the strong interaction among cellulose, GO and TiO2, resulting from the formation of hydrogen bonds. Due to the unique porous structure of cellulose hydrogel and introduction of GO, the cellulose/GO/TiO2 hydrogel showed superior (degradation ratio ∼ 93%) and reproducible (no significant change during the ten consecutive cycles) performance in the removal of MB under UV light. Consequently, the prepared cellulose/GO/TiO2 hydrogel can be applied as an eco-friendly, high-performance, reproducible, and stable photocatalyst and adsorbent for the removal of MB. This green hydrogel is a promising candidate for dye wastewater treatment. Moreover, this work is expected to extend the scope of bio-templated synthesis of other nanomaterials for various applications.

| S-EPMC9055038 | biostudies-literature

<i>In situ</i> synthesis of ZnO-GO/CGH composites for visible light photocatalytic degradation of methylene blue.

Project description:A novel ZnO-GO/CGH composite was prepared using an in situ synthesis process for photodegradation of methylene blue under visible light illumination. The chitin-graphene composite hydrogel (CGH) was used to provide uniform binding of the nano ZnO-GO composite to the hydrogel surface and prevent their agglomeration. GO provides multi-dimensional protons and electron transport channels for ZnO with a flower-like structure, which possessed improved photo-catalytic activity. SEM analysis indicates that the hydrogel has good adsorption properties with rougher surfaces and porous microstructure, which enables it to adsorb the dyes effectively. Under synergetic enhancement of adsorption and photo-catalysis, catalytic activity and nano ZnO-GO/CGH recycling improved greatly. Synthesized nano ZnO-GO/CGH showed high dye removal efficiency of 99%, about 2.2 times that of the pure chitin gel under the same condition. This suggests the potential application of the new photocatalytic composites to remove organic dyes from wastewater.

| S-EPMC9076400 | biostudies-literature

New Composites LnBDC@AC and CB[6]@AC: From Design toward Selective Adsorption of Methylene Blue or Methyl Orange.

Project description:New porous composites LnBDC@AC (AC = Activated carbon, Ln = Eu and Gd and BDC = 1,4-benzenedicaboxylate) and CB[6]@AC (CB[6] = Cucurbit[6]uril) were obtained using hydrothermal route. The LnBDC and CB[B] are located inside the pore of the carbon materials as was observed in SEM-EDS, XRPD and FT-IR analysis. Porosimetry analysis showed values typically between AC and LnBDC material, with pore size and surface area, respectively, 29,56 Å and 353.98 m2g-1 for LnBDC@AC and 35,53 Å and 353.98 m2g-1 for CB[6]@AC. Both materials showed good absorptive capacity of metil orange (MO) and methylene blue (MB) with selectivity as a function of pH. For acid pH, both materials present selectivity by MB and alkaline pH for MO, with notable performance for CB[6]@AC. Additionally, europium luminescence was used as structural probe to investigate the coordination environment of Eu3+ ions in the EuBDC@AC composite after adsorption experiment.

| S-EPMC5249156 | biostudies-literature

A Comparative Study of the Adsorption of Methylene Blue onto Synthesized Nanoscale Zero-Valent Iron-Bamboo and Manganese-Bamboo Composites.

Project description:In this study, bamboo impregnated with nanoscale zero-valent iron (nZVI) and nanoscale manganese (nMn) were prepared by the aqueous phase borohydride reduction method and characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) and PIXE analysis. The synthesized nMn-bamboo and nZVI-bamboo composites were subsequently applied to the sorption of methylene blue (MB) dye from aqueous solution. The adsorption of MB dye was investigated under various experimental conditions such as pH, contact time, initial concentration of MB dye and adsorbent dosage. The results showed that the synthesized nZVI-bamboo composite was more effective than nMn-bamboo composite in terms of higher MB dye adsorption capacity of 322.5 mg/g compared to 263.5 mg/g of nMn-bamboo composite. At a concentration of 140 mg/L MB dye, 0.02 g of nZVI-bamboo and nMn-bamboo composites resulted in 79.6% and 78.3% removal, respectively, at 165 rpm, contact time of 120 min and at a solution pH of 7.6. The equilibrium data was best represented by Freundlich isotherm model and the pseudo-second order kinetic model better explained the kinetic data for both nZVI-bamboo and nMn-bamboo composites.

| S-EPMC5455915 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data