Coupling Adsorption-Photocatalytic Degradation of Methylene Blue and Maxilon Red.
Ontology highlight
ABSTRACT:
SUBMITTER: Farouq R
PROVIDER: S-EPMC9270313 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:This paper reports a zinc derived (ZD) porous nanosystem that has been used for selective sensing, adsorption, and photocatalytic degradation of the known hazardous dye, Methylene blue (MB). Using zinc nitrate and 2-aminoterphthalic acid as precursors, the synthesis has been optimized to yield disc-shaped nanoparticles. This luminescent ZD nanoparticles exhibit absorption and emission wavelengths of 328 nm and 427 nm, respectively at an excitation wavelength of 330 nm. In the presence of MB, there is a sharp decrease in the photoluminescence emission intensity of ZD nanoparticles. The detection limit, quenching constant and the binding constant of ZD nanoparticles with MB are found to be 0.31 × 10-9 M, 3.30 × 106 M-1 and 2.27 × 106 M-1 respectively. The impact of contact time, initial MB concentration, and pH on the adsorption process were investigated. The equilibrium data fit well with the Langmuir adsorption isotherm model (R 2 = 0.989) and superlatively fitted to the pseudo-second-order rate model (rate constant: 0.00011 g mg-1 min-1; adsorption capacity (q e, calc.): 386.1 mg g-1; R 2: 0.990). Further, the MB dye degradation was performed under ultra-violet irradiation and ∼95% MB degradation was achieved within 70 min. The experimental data are well fitted to the pseudo-first order kinetics (R 2: 0.99; rate constant: 0.015 min-1). These disc shaped ZD nanoparticles can not only facilitate the detection, but also the adsorption and photocatalytic degradation of MB, which can be further processed for environmental remediation applications.
| S-EPMC9728022 | biostudies-literature
Project description:Environmentally friendly cellulose/GO/TiO2 hydrogel photocatalyst has been successfully fabricated via a green, simple, and one-step method and evaluated as the photocatalyst and adsorbent for the removal of methylene blue (MB). The XRD and FTIR analysis suggested the strong interaction among cellulose, GO and TiO2, resulting from the formation of hydrogen bonds. Due to the unique porous structure of cellulose hydrogel and introduction of GO, the cellulose/GO/TiO2 hydrogel showed superior (degradation ratio ∼ 93%) and reproducible (no significant change during the ten consecutive cycles) performance in the removal of MB under UV light. Consequently, the prepared cellulose/GO/TiO2 hydrogel can be applied as an eco-friendly, high-performance, reproducible, and stable photocatalyst and adsorbent for the removal of MB. This green hydrogel is a promising candidate for dye wastewater treatment. Moreover, this work is expected to extend the scope of bio-templated synthesis of other nanomaterials for various applications.
| S-EPMC9055038 | biostudies-literature
Project description:Carbon-based TiO? composites have many advantages as photocatalysts. However, they suffer from low light efficiency due to the low contrast of TiO? with carbon. We synthesized a novel type of anatase-type TiO?-C hybrid aerogel by a one-pot sol-gel method, which shows a photocatalytic activity for methylene degradation up to 4.23 times that of P25, a commercial photocatalyst from Degussa Inc. The hybrid aerogels are prepared from TiCl? and resorcinol-furfural, and have a tunable macropore size from 167 to 996 nm. They are formed of submicrometer particles that consist of interwoven anatase and carbon nanoparticles. The anatase nanoparticles have a size of 8-9 nm and a tunable oxygen vacancy from 7.2 to 18.0%. The extremely high activity is ascribed to the large light absorption caused by macropore scattering and oxygen vacancies in the anatase. These findings may open up a new avenue and stimulate further research to improve photocatalytic performance.
| S-EPMC3804859 | biostudies-literature
Project description:SiC foams were synthesized by impregnating preceramic polymer into polyurethane foam templates, resulting in a photo-catalytically active material for the degradation of methylene blue. The crystalline structure, electronic properties, and photocatalytic performance of the SiC foams were characterized using a series of experimental techniques, including X-ray diffraction, electron microscopy, energy dispersive X-ray spectroscopy, N2 physisorption measurements, UV-visible spectroscopy, and methylene blue photodegradation tests. The original polyurethane template's microporous structure was maintained during the formation of the SiC foam, while additional mesopores were introduced by the porogen moieties added to the preceramic polymers. The prepared SiC-based photocatalyst showed attractive photocatalytic activity under visible light irradiation. This structured and reactive material offers good potential for application as a catalytic contactor or membrane reactor for the semi-continuous treatment of contaminated waste waters in ambient conditions.
| S-EPMC9959366 | biostudies-literature
Project description:In this study, zinc oxide nanoparticles (ZnO) and nanohydroxyapatite (NHAP) were prepared in the presence of date palm pits extract (DPPE) and eggshells, respectively. Another four nanocomposites were prepared from ZnO and NHAP in different ratios (ZP13, ZP14, ZP15, and ZP16). DPPE and all nanomaterials were characterized using GC-MS, zeta potentials, particle size distributions, XRD, TEM, EDX, FTIR, and pHPZC. The characterization techniques confirmed the good distribution of ZnO nanoparticles on the surface of NHAP in the prepared composites. Particles were found to be in the size range of 42.3-66.1 nm. The DPPE analysis confirmed the presence of various natural chemical compounds which act as capping agents for nanoparticles. All the prepared samples were applied in the adsorption and photocatalytic degradation of methylene blue under different conditions. ZP14 exhibited the maximum adsorption capacity (596.1 mg/g) at pH 8, with 1.8 g/L as the adsorbent dosage, after 24 h of shaking time, and the static adsorption kinetic process followed a PSO kinetic model. The photocatalytic activity of ZP14 reached 91% after 100 min of illumination at a lower MB concentration (20 mg/L), at pH 8, using 1.5 g/L as the photocatalyst dosage, at 25 °C. The photocatalytic degradation of MB obeyed the Langmuir-Hinshelwood first-order kinetic model, and the photocatalyst reusability exhibited a slight loss in activity (~4%) after five cycles of application.
| S-EPMC8746312 | biostudies-literature
Project description:Industrial chemical pollutants such as methylene blue (MB) dye are released into the water body and potentially cause harm to the human and aquatic biosphere. Therefore, this study aims to synthesize eco-friendly nanocatalysts, i.e., reduced graphene oxide (rGO), zinc oxide (ZnO), and reduced graphene oxide-zinc oxide (rGO@ZnO) nanocomposites, for efficient photocatalytic degradation of MB dye. A graphite rod was obtained from waste dry cell batteries for the electrochemical exfoliation synthesis of graphene oxide (GO) and rGO. For the eco-friendly synthesis of ZnO and rGO@ZnO nanocatalysts, Croton macrostachyus leaf extract was used as a reducing and capping agent. The synthesized nanocatalysts were characterized using a UV-Vis spectrophotometer, Fourier transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy with energy-dispersive X-ray. The eco-friendly synthesized rGO, ZnO, and rGO@ZnO nanocatalysts were applied for the photocatalytic degradation of MB dye using direct sunlight irradiation. At optimum parameters, photocatalytic degradation of MB dye efficiency reached up to 66%, 96.5%, and 99.0%, respectively. Furthermore, kinetics of the photodegradation reaction based on rGO, ZnO, and rGO@ZnO nanocatalysts follow pseudo-first-order with a rate constant of 2.16 × 10-3 min-1, 4.97 × 10-3 min-1, and 5.03 × 10-3 min-1, respectively. Lastly, this study promotes a low catalyst load (20 mg) for the efficient photodegradation of MB dye.
| S-EPMC10721910 | biostudies-literature
Project description:Developing the application of high-strength hydrogels has gained much attention in the fields of medical, pharmacy, and pollutant removal due to their versatility and stimulus-responsive properties. In this presentation, a high-strength freestanding elastic hydrogel membrane was constructed by clay nanosheets, N, N-dimethylacrylamide and 2-acrylamide-2-methylpropanesulfonic acid for adsorption of methylene blue and heavy metal ions. The maximum values of elongation and Young's modulus for 0.5% AMPSNa hydrogel were 1901% and 949.4 kPa, respectively, much higher than those of traditional hydrogels. The adsorptions were confirmed to follow pseudo-second kinetic equation and Langmuir isotherm model fits the data well. The maximum adsorption capacity of hydrogel towards methylene blue was 434.8 mg g(-1). The hydrogel also exhibited higher separation selectivity to Pb(2+) than Cu(2+). The methylene blue adsorbed onto the hydrogel membrane can be photocatalytically degraded by Fenton agent and the hydrogel membrane could be recycled at least five times without obvious loss in mechanical properties. In conclusion, this presentation demonstrates a convenient strategy to prepare tough and elastic clay nanocomposite hydrogel, which can not only be applied as recyclable membrane for the photocatalytic degradation of organic dye, but also for the recovery of valuables.
| S-EPMC3930577 | biostudies-literature
Project description:In this work, C-doped TiO2 nanorods were synthesized through doping carbon black into hydrothermally synthesized solid-state TiO2 nanowires (NWs) via calcination. The effects of carbon content on the morphology, phase structure, crystal structure, and photocatalytic property under both UV and solar light by the degradation of methylene blue (MB) were explored. Besides, the photoelectrochemical property of C-TiO2 was systematically studied to illustrate the solar light degradation mechanism. After doping with C, TiO2 NWs were reduced into nanorods and the surface became rough with dispersed particles. Results showed that C has successfully entered the TiO2 lattice, resulting in the lattice distortion, reduction of band gap, and the formation of C-Ti-O, which expands TiO2 to solar light activation. Comparing with P25 and anatase TiO2 NWs, doping with carbon black showed much higher UV light and solar light photocatalytic activity. The photocatalytic activity was characterized via the degradation of MB, showing that K ap was 0.0328 min-1 under solar light, while 0.1634 min-1 under UV irradiation. The main free radicals involved in methylene blue degradation are H+ and OH•-. Doping with carbon black led to the reduction of photocurrent in a long-term operation, while C-doping reduced the electron-hole recombination and enhanced the carrier migration.
| S-EPMC7203985 | biostudies-literature
Project description:The present study highlights the facile synthesis of polyaniline (PANI)-based nanocomposites doped with SrTiO₃ nanocubes synthesized via the in situ oxidative polymerization technique using ammonium persulfate (APS) as an oxidant in acidic medium for the photocatalytic degradation of methylene blue dye. Field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), X-ray diffraction (XRD), UV⁻Vis spectroscopy, Brunauer⁻Emmett⁻Teller analysis (BET) and Fourier transform infrared spectroscopy (FTIR) measurements were used to characterize the prepared nanocomposite photocatalysts. The photocatalytic efficiencies of the photocatalysts were examined by degrading methylene blue (MB) under visible light irradiation. The results showed that the degradation efficiency of the composite photocatalysts that were doped with SrTiO₃ nanocubes was higher than that of the undoped polyaniline. In this study, the effects of the weight ratio of polyaniline to SrTiO₃ on the photocatalytic activities were investigated. The results revealed that the nanocomposite P-Sr500 was found to be an optimum photocatalyst, with a 97% degradation efficiency after 90 min of irradiation under solar light.
| S-EPMC6432585 | biostudies-literature
Project description:Photocatalytic degradation is a promising method for removing persistent organic pollutants from water because of its low cost (see solar-driven photocatalysis), high mineralisation of pollutants, and low environmental impact. Photocatalysts based on transition metal dichalcogenides (TMDs) have recently attracting high scientific interest due to their unique electrical, mechanical, and optical properties. A MoS2 photocatalyst of the layered structure was managed to photodegrade methylene blue (MB) under visible light irradiation. The catalyst was thoroughly characterised using SEM, AFM, powder XRD, UV-Vis, Raman, and XPS measurements. The photocatalytic degradation of the MB solution was conducted under the following conditions: (i) reductive and (ii) oxidative. The impact of optical and electronic properties, and the MoS2-MB interaction on photocatalytic activity, was discussed. The apparent rate constants (kapp) of degradation were 3.7 × 10-3; 7.7 × 10-3; 81.7 × 10-3 min-1 for photolysis, oxidative photocatalysis, and reductive photocatalysis. Comparison of the degradation efficiency of MB in reductive and oxidative processes indicates the important role of the reaction with the surface electron. In the oxidation process, oxygen reacts with an electron to form a superoxide anion radical involved in further transformations of the dye, whereas, in the reduction process, the addition of an electron destabilises the chromophore ring and leads to its rupture.
| S-EPMC10465577 | biostudies-literature