Improving the Stability and Efficiency of Perovskite Solar Cells by a Bidentate Anilinium Salt.
Ontology highlight
ABSTRACT:
SUBMITTER: Scalon L
PROVIDER: S-EPMC9241004 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:In this study, our hypothesis was to demonstrate the usability of a natural clay structure as scaffold layer in perovskite solar cells (PSCs). Sepiolite, which is a natural and environmentally friendly clay structure, has a very high active surface area and can easily be dispersed in solvents. In addition we predicted that crystallization could easily occur on their surfaces due to their surface chemistry. In the study, we firstly used a natural clay as scaffold layer in PSCs. It is observed that, efficiency, reproducibility and stability of PSCs have been significantly improved. Improvements in efficiency have been observed to be between 30 and 50% depending on the type of perovskite solvent used. In addition, the surface chemistry of the sepiolite resulted in better crystallization as well as stability. Due to its high-water adsorption capability, sepiolite makes the perovskite crystal more stable by trapping the residual water molecules as well as penetrated water molecules from environment. Consequently, we demonstrated that, a natural, low-cost and environmentally friendly clay may be an alternative material which may contribute to the commercialization of PSCs.
| S-EPMC10017716 | biostudies-literature
Project description:The advancement of perovskite solar cells (PVSCs) technology toward commercialized promotion needs high efficiency and optimum stability. By introducing a small molecular material such as tetratetracontane (TTC, CH3(CH2)42CH3) at the fullerene (C60)/perovskite interface of planar p-i-n PVSCs, we significantly reduced the interfacial traps, thereby suppressing electron recombination and facilitating electron extraction. Consequently, an improved efficiency of 20.05% was achieved with a high fill factor of 79.4%, which is one of the best performances for small molecular-modified PVSCs. Moreover, the hydrophobic TTC successfully protects the perovskite film from water damage. As a result, we realized a better long-term stability that maintains 87% of the initial efficiency after continuous exposure for 200 h in air.
| S-EPMC7770653 | biostudies-literature
Project description:Organic Lewis bases [2,2'-bipyridine (BPY), 4-hydroxy-1,5-naphthyridine-3-carbonitrile (DQCN), and thenoyltrifluoroacetone (TTFA)] with bi-coordination sites of N and O were employed as perovskite surface defect passivants to address the efficiency and stability issues of perovskite solar cells (PSCs), with typical phenethylammonium iodide (PEAI) and piperazinium iodide (PI) passivants as reference. The surface properties of the perovskite films before and after passivation were characterized by Fourier-transform infrared, ultraviolet-visible, photoluminescence (PL), and time-resolved PL spectroscopy, X-ray diffraction, ultraviolet photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy. The characterizations reveal that BPY, DQCN, or TTFA forms coordination bonds with exposed "Pb2+", leading to a slight decrease in the highest occupied molecular orbital or lowest unoccupied molecular orbital energy level and bandgap. These passivants (especially TTFA) can passivate the perovskite surface defects to inhibit non-radiative recombination while having almost no influence on the grain size and surface morphology. Utilizing the passivated perovskite as the light absorption layer, solar cells with an inverted configuration of indium tin oxide/NiO x /passivated MAPbCl x I3-x /C60/BCP/Ag have been fabricated, and power conversion efficiencies of 19.22, 17.85, 16.49, 16.31, and 17.88% have been achieved from PEAI, PI, BPY, DQCN, and TTFA, respectively. All the device performance based on passivated perovskite is superior to that of the control (15.75%) owing to the reduced carrier recombination. The device from TTFA exhibits almost comparable efficiency to that of PEAI and PI controls, indicating that TTFA has an equal excellent passivation effect to state-of-the-art PEAI and PI. Furthermore, the devices based on BPY, DQCN, and TTFA show superior long-term stability with an efficiency loss of only 13.2, 16.7, and 12.9%, respectively, after being stored for 40 days in a ∼12% humidity, low-oxygen level environment, which is 45.4, 38.8, and 44.4% for the control, PEAI, and PI devices, respectively, primarily due to the improved hydrophobicity of the perovskite surface. Our results demonstrate that it is feasible to achieve high-efficiency and long-term-stable perovskite solar cells via selecting the appropriate molecules to passivate perovskite surface defects.
| S-EPMC9476505 | biostudies-literature
Project description:Today's best perovskite solar cells use a mixture of formamidinium and methylammonium as the monovalent cations. With the addition of inorganic cesium, the resulting triple cation perovskite compositions are thermally more stable, contain less phase impurities and are less sensitive to processing conditions. This enables more reproducible device performances to reach a stabilized power output of 21.1% and ?18% after 250 hours under operational conditions. These properties are key for the industrialization of perovskite photovoltaics.
| S-EPMC4936376 | biostudies-literature
Project description:Perovskite solar cells present one of the most prominent photovoltaic technologies, yet their stability, scalability, and engineering at the molecular level remain challenging. We demonstrate a concept of multifunctional molecular modulation of scalable and operationally stable perovskite solar cells that exhibit exceptional solar-to-electric power conversion efficiencies. The judiciously designed bifunctional molecular modulator SN links the mercapto-tetrazolium (S) and phenylammonium (N) moieties, which passivate the surface defects, while displaying a structure-directing function through interaction with the perovskite that induces the formation of large grain crystals of high electronic quality of the most thermally stable formamidinium cesium mixed lead iodide perovskite formulation. As a result, we achieve greatly enhanced solar cell performance with efficiencies exceeding 20% for active device areas above 1?cm2 without the use of antisolvents, accompanied by outstanding operational stability under ambient conditions.
| S-EPMC6203709 | biostudies-literature
Project description:A high-mobility p-type organic semiconductor based on benzodithiophene and diketopyrrolopyrrole with linear alkylthio substituents (BDTS-2DPP) is used as a dual function interfacial layer to modify the interface of perovskite/2,2',7,7'-tetrakis(N,N'-di-p-methoxyphenylamine)-9,9'-spirobifluorene in planar perovskite solar cells. The BDTS-2DPP layer can remarkably passivate the surface defects of perovskite through the formation of Lewis adduct between the under-coordinated Pb atoms in perovskite and S atoms in BDTS-2DPP, and also shows efficient hole extraction and transfer properties. The devices with BDTS-2DPP interlayer show a peak power conversion efficiency of 18.2%, which is higher than that of reference devices without the BDTS-2DPP interlayer (16.9%). Moreover, the hydrophobic BDTS-2DPP interlayer effectively protects the perovskite against moisture, leading to enhanced device stability.
| S-EPMC5604372 | biostudies-literature
Project description:While perovskite solar cells have reached competitive efficiency values during the last decade, stability issues remain a critical challenge to be addressed for pushing this technology towards commercialisation. In this study, we analyse a large homogeneous dataset of Maximum Power Point Tracking (MPPT) operational ageing data that we collected with a custom-built High-throughput Ageing System in the past 3 years. In total, 2,245 MPPT ageing curves are analysed which were obtained under controlled conditions (continuous illumination, controlled temperature and atmosphere) from devices comprising various lead-halide perovskite absorbers, charge selective layers, contact layers, and architectures. In a high-level statistical analysis, we find a correlation between the maximum reached power conversion efficiency (PCE) and the relative PCE loss observed after 150-hours of ageing, with more efficient cells statistically also showing higher stability. Additionally, using the unsupervised machine learning method self-organising map, we cluster this dataset based on the degradation curve shapes. We find a correlation between the frequency of particular shapes of degradation curves and the maximum reached PCE.
| S-EPMC10423264 | biostudies-literature
Project description:The instability of hybrid perovskite materials due to water and moisture arises as one major challenge to be addressed before any practical application of the demonstrated high efficiency perovskite solar cells. Here we report a facile strategy that can simultaneously enhance the stability and efficiency of p-i-n planar heterojunction-structure perovskite devices. Crosslinkable silane molecules with hydrophobic functional groups are bonded onto fullerene to make the fullerene layer highly water-resistant. Methylammonium iodide is introduced in the fullerene layer for n-doping via anion-induced electron transfer, resulting in dramatically increased conductivity over 100-fold. With crosslinkable silane-functionalized and doped fullerene electron transport layer, the perovskite devices deliver an efficiency of 19.5% with a high fill factor of 80.6%. A crosslinked silane-modified fullerene layer also enhances the water and moisture stability of the non-sealed perovskite devices by retaining nearly 90% of their original efficiencies after 30 days' exposure in an ambient environment.
| S-EPMC5059465 | biostudies-literature
Project description:The power conversion efficiencies (PCEs) of perovskite solar cells (PSCs) are already higher than that of other thin film technologies, but laboratory cell-fabrication methods are not scalable. Here, we report an additive strategy to enhance the efficiency and stability of PSCs made by scalable blading. Blade-coated PSCs incorporating bilateral alkylamine (BAA) additives achieve PCEs of 21.5 (aperture, 0.08 cm2) and 20.0% (aperture, 1.1 cm2), with a record-small open-circuit voltage deficit of 0.35 V under AM1.5G illumination. The stabilized PCE reaches 22.6% under 0.3 sun. Anchoring monolayer bilateral amino groups passivates the defects at the perovskite surface and enhances perovskite stability by exposing the linking hydrophobic alkyl chain. Grain boundaries are reinforced by BAA and are more resistant to mechanical bending and electron beam damage. BAA improves the device shelf lifetime to >1000 hours and operation stability to >500 hours under light, with 90% of the initial efficiency retained.
| S-EPMC6408151 | biostudies-literature
Project description:The achievement of perfect light absorption in ultrathin semiconductor materials is not only a long-standing goal, but also a critical challenge for solar energy applications, and thus requires a redesigned strategy. Here, a general strategy is demonstrated both theoretically and experimentally to create a planar metasurface absorber comprising a 1D ultrathin planar semiconductor film (replacing the 2D array of subwavelength elements in classical metasurfaces), a transparent spacer, and a metallic back reflector. Guided by derived formulisms, a new type of macroscopic planar metasurface absorber is experimentally demonstrated with light near-perfectly and exclusively absorbed by the ultrathin semiconductor film. To demonstrate the power and simplicity of this strategy, a prototype of a planar metasurface solar cell is experimentally demonstrated. Furthermore, the device model predicts that a colored planar metasurface perovskite solar cell can maintain 75% of the efficiency of its black counterpart despite the use of a perovskite film that is one order of magnitude thinner. The displayed cell colors have high purities comparable to those of state-of-the-art color filters, and are insensitive to viewing angles up to 60°. The general theoretical framework in conjunction with experimental demonstrations lays the foundation for designing miniaturized, planar, and multifunctional solar cells and optoelectronic devices.
| S-EPMC6193155 | biostudies-literature