Browse
Submit Data
Databases
API
Help

Dataset Information

15 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Residual stress determination by the layer removal and X-ray diffraction measurement - correction method.

ABSTRACT: Very often a manufacturing process is followed by some surface treatment. Such a process induces residual stress into the manufactured component. Compressive residual stress is desirable for enhancing the fatigue properties of the component. The residual stress is often measured only at the surface, if at all. However, residual stress is equilibrating in the whole component. Therefore, compressive residual stress at the surface induces undesirable tensile stress inside in the component. Knowledge of the residual stress distribution in a body can be very useful in engineering applications. The authors found this knowledge necessary for a proper description of fatigue crack propagation in railway axles described in the original paper [1]. With the onset of modern surface treating technologies, e.g. induction hardening, which can affect the entire cross-section of the component, the residual stress determination is even more critical. The presented paper aims to describe a procedure developed for proper residual stress determination. The procedure can be easily used e.g. in R&D centers, where X-ray diffraction residual stress measurement is already in use. The procedure is suitable for the residual stress determination in sizable cylindrical bodies or components, e.g. railway axles. It uses X-ray diffraction residual stress surface measurement and layer removal by machining. Results experimentally obtained are corrected by a general procedure developed in MATLAB software in order to obtain the original residual stress state in the cylindrical body.•More accurate procedure for a residual stress determination in cylindrical bodies.

SUBMITTER: Dlhy P

PROVIDER: S-EPMC9253484 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Dataset on full width at half maximum of residual stress measurement of electron beam welded high strength structural steels (S960QL and S960M) by X-ray diffraction method.

Project description:In this paper, we presented the dataset values of full width at half maximum (FWHM) with errors at each point corresponding to the value of longitudinal and transverse residual stress along the three lines for 14 points measured in the EBW welded joints (S960QL and S960M) of the related article [1]. This dataset is used to plot figures and describes their correspondence points with the interrelation of the residual stress graphs (Fig. 4) of the article [1]. The shape of the diffracted peak can be characterised in a simple way by the FWHM, which is the width in degree at half the peak height after background extraction. The measured width consist of instrumental and metallurgical broadening. The variation or increase in FWHM is resulted from the crystalline lattice defect e.g. solute foreign atoms, dislocations and grain boundary. Conversely, if we can determine the physical broadening, we get more information about the structure of the investigated material. In addition, the optical microscopic image of the base materials and weld microstructure are the other parts of the data. Diffraction data were collected using centreless X-ray diffraction (XRD) during in situ residual stress measurement of high strength structural steels S960QL and S960M. A more detailed interpretation of the data presented in this article is provided in article [1]. The presented data are produced as part of the main work entitled "Comparative evaluation of residual stresses in vacuum electron beam welded high strength steel S960QL and S960M butt joints [1]".

| S-EPMC8437781 | biostudies-literature

The interaction of fatigue cracks with a residual stress field using thermoelastic stress analysis and synchrotron X-ray diffraction experiments.

Project description:This article presents an experimental study on the fatigue behaviour of cracks emanating from cold-expanded holes utilizing thermoelastic stress analysis (TSA) and synchrotron X-ray diffraction (SXRD) techniques with the aim of resolving the long-standing ambiguity in the literature regarding potential relaxation, or modification, of beneficial compressive residual stresses as a result of fatigue crack propagation. The crack growth rates are found to be substantially lower as the crack tip moved through the residual stress zone induced by cold expansion. The TSA results demonstrated that the crack tip plastic zones were reduced in size by the presence of the residual compressive stresses induced by cold expansion. The crack tip plastic zones were found to be insignificant in size in comparison to the residual stress zone resulting from cold expansion, which implied that they were unlikely to have had a notable impact on the surrounding residual stresses induced by cold expansion. The residual stress distributions measured along the direction of crack growth, using SXRD, showed no signs of any significant stress relaxation or redistribution, which validates the conclusions drawn from the TSA data. Fractographic analysis qualitatively confirmed the influence on crack initiation of the residual stresses induced by the cold expansion. It was found that the application of single compressive overload caused a relaxation, or reduction in the residual stresses, which has wider implications for improving the fatigue life.

| S-EPMC5717669 | biostudies-literature

X-ray laser diffraction for structure determination of the rhodopsin-arrestin complex.

Project description:Serial femtosecond X-ray crystallography (SFX) using an X-ray free electron laser (XFEL) is a recent advancement in structural biology for solving crystal structures of challenging membrane proteins, including G-protein coupled receptors (GPCRs), which often only produce microcrystals. An XFEL delivers highly intense X-ray pulses of femtosecond duration short enough to enable the collection of single diffraction images before significant radiation damage to crystals sets in. Here we report the deposition of the XFEL data and provide further details on crystallization, XFEL data collection and analysis, structure determination, and the validation of the structural model. The rhodopsin-arrestin crystal structure solved with SFX represents the first near-atomic resolution structure of a GPCR-arrestin complex, provides structural insights into understanding of arrestin-mediated GPCR signaling, and demonstrates the great potential of this SFX-XFEL technology for accelerating crystal structure determination of challenging proteins and protein complexes.

| S-EPMC4828943 | biostudies-literature

Stress entropic load: New stress measurement method?

Project description:While stress is a widely utilized concept, no direct methods facilitating its measurement are currently available. In our previous work we proposed stress entropic load (SEL) as a potential new marker of stress response in the human body. However, at that time no method for SEL measurement existed. In this pilot study we devised and then tested methodology for SEL measurement. Healthy male participants were monitored by indirect calorimetry and thermography while resting and subsequently while under prolonged mental effort. The acquired data was then used to calculate the temporal development of SEL for each participant. Our results show that SEL production increased significantly in participants subjected to prolonged mental effort. Furthermore, we observed that the calculated development of SEL over time may be used to accurately determine the time point at which participants started performing stressful tasks.

| S-EPMC6193677 | biostudies-literature

3D-printed equipment to decouple (powder) X-ray diffraction sample preparation and measurement

Project description:A method to separate sample preparation from X-ray diffraction and powder X-ray diffraction measurements is presented. The necessary equipment is accessible at low cost by 3D printing. An alternative storage method to separate sample preparation from single-crystal and powder X-ray diffraction measurements at home source diffractometers is described. For single crystals, a setup is presented which allows storage of preselected crystals under cryogenic and ambient temperatures. For powders, a disposable sample holder is introduced. The method is suitable for the storage of air- and moisture-sensitive samples. Equipment made of biodegradable polylactic acid is produced by 3D printing and can be adapted to individual needs. As 3D printers are widely available at research institutions nowadays, models of the presented equipment are provided for the reader to allow easy reproduction.

| S-EPMC9172037 | biostudies-literature

Calculation and realization of new method grey residual error correction model.

Project description:Aiming at the problem of prediction accuracy of stochastic volatility series, this paper proposes a method to optimize the grey model(GM(1,1)) from the perspective of residual error. In this study, a new fitting method is firstly used, which combines the wavelet function basis and the least square method to fit the residual data of the true value and the predicted value of the grey model(GM(1,1)). The residual prediction function is constructed by using the fitting method. Then, the prediction function of the grey model(GM(1,1)) is modified by the residual prediction function. Finally, an example of the wavelet residual-corrected grey prediction model (WGM) is obtained. The test results show that the fitting accuracy of the wavelet residual-corrected grey prediction model has irreplaceable advantages.

| S-EPMC8289091 | biostudies-literature

SPIND-TC: an indexing method for two-color X-ray diffraction data.

Project description:Recent developments of two-color operation modes at X-ray free-electron laser facilities provide new research opportunities, such as X-ray pump/X-ray probe experiments and multiple-wavelength anomalous dispersion phasing methods. However, most existing indexing methods were developed for indexing diffraction data from monochromatic X-ray beams. Here, a new algorithm is presented for indexing two-color diffraction data, as an extension of the sparse-pattern indexing algorithm SPIND, which has been demonstrated to be capable of indexing diffraction patterns with as few as five peaks. The principle and implementation of the two-color indexing method, SPIND-TC, are reported in this paper. The algorithm was tested on both simulated and experimental data of protein crystals. The results show that the diffraction data can be accurately indexed in both cases. Source codes are publicly available at https://github.com/lixx11/SPIND-TC.

| S-EPMC7233013 | biostudies-literature

Machining Stresses and Initial Geometry on Bulk Residual Stresses Characterization by On-Machine Layer Removal.

Project description:Prediction and control of machining distortion is a primary concern when manufacturing monolithic components due to the high scrap and rework costs involved. Bulk residual stresses, which vary from blank to blank, are a major factor of machining distortion. Thus, a bulk stress characterization is essential to reduce manufacturing costs linked to machining distortion. This paper proposes a method for bulk stress characterization on aluminium machining blanks, suitable for industrial application given its low requirements on equipment, labour expertise, and computation time. The method couples the effects of bulk residual stresses, machining stresses resulting from cutting loads on the surface and raw geometry of the blanks, and presents no size limitations. Experimental results confirm the capability of the proposed method to measure bulk residual stresses effectively and its practicality for industrial implementation.

| S-EPMC7143653 | biostudies-literature

Quantitative Deviation of Nanocrystals Using the RIR Method in X-ray Diffraction (XRD).

Project description:The reference intensity ratio (RIR) method, using X-ray diffraction (XRD), is considered one most of the rapid and convenient approaches for phase quantification in multi-phase mixture, in which nanocrystals are commonly contained in a mixture and cause a broadening of the diffraction peak, while another broadening factor, instrumental broadening, does not attract enough attention in related quantitative analysis. Despite the specimen consisting of 50 wt.% TiO2 nanomaterials (nano-TiO2) and 50 wt.% microscale ZnO powder, the nano-TiO2 quantitative result changes from 56.53% to 43.33% that occur as a variation of instrumental broadening are caused by divergence slit adjustment. This deviation could be accounted through a mathematical model that involves instrumental broadening. The research in this paper might provide a useful guide for developing an approach to measure accuracy quantification in unknown multi-phase mixtures.

| S-EPMC9325253 | biostudies-literature

Understanding Inhomogeneous Reactions in Li-Ion Batteries: Operando Synchrotron X-Ray Diffraction on Two-Layer Electrodes.

Project description:To understand inhomogeneous reactions perpendicular to the current collector in an electrode for batteries, a method combining operando synchrotron X-ray diffraction and two-layer electrodes with different porosities is developed. The two layers are built using two different active materials (LiNi0.80Co0.15Al0.05O2 and LiMn2O4), therefore, tracing each diffraction pattern reveals which active material is reacting during the electrochemical measurement in transmission mode. The results demonstrate that the active material close to the separator is obviously more active than that one close to the current collector in the case of low porosity electrodes. This inhomogeneity should be due to the rate-limitation and especially to low average ionic conductivity of the electrolyte in the porous electrode because the current flows first mainly into the electrode regions close to the separator. The inhomogeneity is found to be mitigated by the adjustment of the electrode density and thus porosity. Hence, the novel operando method reveals a clear inhomogeneous reaction perpendicular to the current collector.

| S-EPMC5033016 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data