Dataset Information

Locking Plates With Computationally Enhanced Screw Trajectories Provide Superior Biomechanical Fixation Stability of Complex Proximal Humerus Fractures.

ABSTRACT: Joint-preserving surgical treatment of complex unstable proximal humerus fractures remains challenging, with high failure rates even following state-of-the-art locked plating. Enhancement of implants could help improve outcomes. By overcoming limitations of conventional biomechanical testing, finite element (FE) analysis enables design optimization but requires stringent validation. This study aimed to computationally enhance the design of an existing locking plate to provide superior fixation stability and evaluate the benefit experimentally in a matched-pair fashion. Further aims were the evaluation of instrumentation accuracy and its potential influence on the specimen-specific predictive ability of FE. Screw trajectories of an existing commercial plate were adjusted to reduce the predicted cyclic cut-out failure risk and define the enhanced (EH) implant design based on results of a previous parametric FE study using 19 left proximal humerus models (Set A). Superiority of EH versus the original (OG) design was tested using nine pairs of human proximal humeri (N = 18, Set B). Specimen-specific CT-based virtual preoperative planning defined osteotomies replicating a complex 3-part fracture and fixation with a locking plate using six screws. Bone specimens were prepared, osteotomized and instrumented according to the preoperative plan via a standardized procedure utilizing 3D-printed guides. Cut-out failure of OG and EH implant designs was compared in paired groups with both FE analysis and cyclic biomechanical testing. The computationally enhanced implant configuration achieved significantly more cycles to cut-out failure compared to the standard OG design (p < 0.01), confirming the significantly lower peri-implant bone strain predicted by FE for the EH versus OG groups (p < 0.001). The magnitude of instrumentation inaccuracies was small but had a significant effect on the predicted failure risk (p < 0.01). The sample-specific FE predictions strongly correlated with the experimental results (R² = 0.70) when incorporating instrumentation inaccuracies. These findings demonstrate the power and validity of FE simulations in improving implant designs towards superior fixation stability of proximal humerus fractures. Computational optimization could be performed involving further implant features and help decrease failure rates. The results underline the importance of accurate surgical execution of implant fixations and the need for high consistency in validation studies.

SUBMITTER: Mischler D

PROVIDER: S-EPMC9260250 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:INTRODUCTION:In locked plate fixation of proximal humerus fractures, the calcar is an important anchor point for screws providing much-needed medial column support. Most locking plate implants utilize a fixed-trajectory locking screw to achieve this goal. Consequently, adjustments of plate location to account for patient-specific anatomy may result in a screw position outside of the calcar. To date, little is known about the consequences of "missing" the calcar during plate positioning. This study sought to characterize the biomechanics associated with proximal and distal placement of locking plates in a two-part fracture model. MATERIALS AND METHODS:This experiment was performed twice, first with elderly cadaveric specimens and again with osteoporotic sawbones. Two-part fractures were simulated and specimens were divided to represent proximal, neutral, and distal plate placements. Non-destructive torsional and axial compression tests were performed prior to an axial fatigue test and a ramp to failure. Torsional stiffness, axial stiffness, humeral head displacement and stiffness during fatigue testing, and ultimate load were compared between groups. RESULTS:Cadavers: Proximal implant placement led to trends of decreased mechanical properties, but there were no significant differences found between groups. Sawbones: Distal placement increased torsional stiffness in both directions (p?=?0.003, p?=?0.034) and axial stiffness (p?=?0.018) when compared to proximal placement. Distal placement also increased torsional stiffness in external rotation (p?=?0.020), increased axial stiffness (p?=?0.024), decreased humeral head displacement during fatigue testing, and increased stiffness during fatigue testing when compared to neutral placement. DISCUSSION:The distal and neutral groups had similar mechanical properties in many cadaveric comparisons while the proximal group trended towards decreased construct stiffness. RESULTS:from the Sawbones model were more definitive and provided further evidence that proximal calcar screw placements are undesirable and distal implant placement may provide improved construct stability. CONCLUSION:Successful proximal humerus fracture reconstruction is inherent upon anatomic fracture reduction coupled with medial column support. Results from this experiment suggest that missing the calcar proximally is deleterious to fixation strength, while it is safe, and perhaps even desirable, to aim slightly distal to the intended target.

Project description:BackgroundThe locking plate is a useful treatment for lateral clavicle fractures, however, there are limits to the fragment size that can be fixed. The current study aimed to measure the screw angles of three locking plates for lateral clavicle fractures. In addition, to assess the number of screws that can be inserted in different fragment sizes, to elucidate the size limits for locking plate fixation.MethodsThe following three locking plates were analyzed: the distal clavicle plate [Acumed, LLC, Oregon, the USA], the LCP clavicle plate lateral extension [Depuy Synthes, LLC, PA, the USA], and the HAI clavicle plate [HOMS Engineering, Inc., Nagano, Japan]. We measured the angles between the most medial and lateral locking screws in the coronal plane and between the most anterior and posterior locking screws in the sagittal plane. A computer simulation was used to position the plates as laterally as possible in ten normal three-dimensional clavicle models. Lateral fragment sizes of 10, 15, 20, 25, and 30 mm were simulated in the acromioclavicular joint, and the number of screws that could be inserted in the lateral fragment was assessed. Subsequently, the area covered by the locking screws on the inferior surface of the clavicle was measured.ResultsThe distal clavicle plate had relatively large screw angles (20° in the coronal plane and 32° in the sagittal plane). The LCP clavicle lateral extension had a large angle (38°) in the sagittal plane. However, the maximum angle of the HAI clavicle plate was 13° in either plane. The distal clavicle plate allowed most screws to be inserted in each size of bone fragment. For all locking plates, all screws could be inserted in 25 mm fragments. The screws of distal clavicle plate covered the largest area on the inferior surface of the clavicle.ConclusionsScrew angles and the numbers of screws that could be inserted in the lateral fragment differed among products. Other augmented fixation procedures should be considered for fractures with fragment sizes < 25 mm that cannot be fixed with a sufficient number of screws.

Project description:PURPOSE: Fixed-angle devices have been a major advancement in orthopedic fracture care and have become an attractive option for fixation of distal radius fractures. Several volar locking plates exist, but there is insufficient literature comparing the strengths of these plates. This study compares the biomechanical strength of two popular volar locking plate systems (Synthes LCP and Hand Innovations DVR-A) along with a nonlocking volar T-plate (Synthes). METHODS: Twenty-three formalin-fixed cadaveric forearms were divided into three groups with similar ages and bone densities. An unstable extra-articular fracture was created using a standardized osteotomy. Each group was fixed with one of the three plates. Each specimen was loaded in axial compression for 2000 cycles at a force of 400 N. Each specimen that completed cyclic testing was loaded to failure. Stiffness, yield point, and ultimate strength were recorded for each construct. RESULTS: Each fixed-angle construct completed all 2000 cycles. The nonlocking plates failed at an average of 560 cycles. The mean stiffness of the DVR-A, LCP, and the volar T-plates were 277.00, 343.17, and 175.67 N/mm, respectively. There was a statistically significant difference between both fixed-angle plates and the nonlocking plate (p < 0.05). The difference between each fixed-angle construct did not reach significance. Yield point and ultimate strength could only be determined for the two fixed-angle devices. There was no statistically significant difference between the constructs for both yield point (DVR-A = 855.56 N, LCP = 894.15 N) and ultimate strength (DVR-A = 1,021.97 N, LCP = 1,114.87 N). CONCLUSIONS: Given our data, fixed-angle constructs withstand cyclical loading representing normal physiologic forces encountered during post-operative rehabilitation. There was no significant biomechanical difference between the two fixed-angle constructs. Our results support that volar fixed-angle locking plates are an effective treatment for unstable extra-articular distal radius fractures, allowing early postoperative rehabilitation to safely be initiated.

Project description:BackgroundProximal humerus fractures are the third most common in the human body but their management remains controversial. Open reduction and internal fixation with plates is one of the leading modes of operative treatment for these fractures. The development of technologies and techniques for these plates, during the recent decades, promise a bright future for their clinical use. A comprehensive review of in vitro biomechanical studies is needed for the comparison of plates' mechanical performance and the testing methodologies. This will not only guide clinicians with plate selection but also with the design of future in vitro biomechanical studies. This review was aimed to systematically categorise and review the in vitro biomechanical studies of these plates based on their protocols and discuss their results. The technologies and techniques investigated in these studies were categorised and compared to reach a census where possible.Methods and resultsWeb of Science and Scopus database search yielded 62 studies. Out of these, 51 performed axial loading, torsion, bending and/or combined bending and axial loading while 11 simulated complex glenohumeral movements by using tendons. Loading conditions and set-up, failure criteria and performance parameters, as well as results for each study, were reviewed. Only two studies tested four-part fracture model while the rest investigated two- and three-part fractures. In ten studies, synthetic humeri were tested instead of cadaveric ones. In addition to load-displacement data, three-dimensional motion analysis systems, digital image correlation and acoustic emission testing have been used for measurement.ConclusionsOverall, PHILOS was the most tested plate and locking plates demonstrated better mechanical performance than non-locking ones. Conflicting results have been published for their comparison with non-locking blade plates and polyaxial locking screws. Augmentation with cement [calcium phosphate or poly(methyl methacrylate)] or allografts (fibular and femoral head) was found to improve bone-plate constructs' mechanical performance. Controversy still lies over the use of rigid and semi-rigid implants and the insertion of inferomedial screws for calcar region support. This review will guide the design of in vitro and in silico biomechanical tests and also supplement the study of clinical literature.

Project description:PurposeTo investigate the clinical outcomes following the arthroscopic removal of proximal humerus locking plates for symptomatic hardware after open reduction and internal fixation (ORIF) of proximal humerus fractures.MethodsPatients who underwent arthroscopic removal of hardware (ROH) with capsular release due to pain and/or immobility after receiving locking plates to treat proximal humerus fractures from 2009 to 2016 were identified. Operative and clinic records were reviewed to obtain demographic information, concomitant procedures during ROH, and pre- and postoperative active shoulder range of motion. Postoperative patient-reported outcomes included the QuickDASH, PROMIS Pain Intensity, Constant, and University of California, Los Angeles shoulder rating scale.ResultsIn total, 88 patients were included. Patients were evaluated at a minimum of 6 weeks postoperatively after ROH. Patients with pre- and postoperative active range of motion values demonstrated significant improvements in mean forward elevation (n = 69; 78.4%; 115.1° to 152.1°, P < .001), abduction (n = 29; 33.0%; 70.9° to 138.7°, P < .001), external rotation (n = 49; 55.7%; 43.7° to 58.6°, P = .012), and internal rotation (n = 45; 51.1%; 25.7° to 61.9°, P < .001). Patients also reported positive patient-reported scores, including the QuickDASH (4.1 ± 7.8), PROMIS Pain Intensity (3.5 ± 0.9), Constant (84.6 ± 10.7), and University of California, Los Angeles shoulder rating scale (33 ± 2.9), which were measured 70.6 ± 26.6 months postoperatively. There were no surgical complications, no arthroscopic cases were converted to open, but 2 reported refractures (2.3%).ConclusionsArthroscopic-assisted removal of proximal humerus locking plates significantly improves motion and function while allowing for management of concomitant shoulder pathology and potentially avoiding open surgery complications. Given that patients undergoing this procedure frequently have multiple comorbidities, arthroscopic-assisted removal with smaller incisions may minimize risks while restoring shoulder mobility. Therefore, arthroscopic ROH for patients experiencing symptomatic hardware after ORIF is recommended.Level of evidenceLevel IV, therapeutic case series.

Project description:BACKGROUND:Geriatric acetabular fractures require fixation with sufficient primary stability to allow for immediate full-weight bearing. Minimally-invasive procedures would be desirable in order to keep perioperative morbidity low. The purpose of this study was to compare the biomechanical strength of lag screw-only fixation of anterior column posterior hemi-transverse (ACPHT) acetabular fractures to standard anatomical plate fixation. METHODS:Standardized ACPHT fractures were created in fourth generation synthetic pelvis models and stabilized by either an anatomical buttress plate (n?=?4) or by a screw-only construct (n?=?4). In a validated setup, a cyclic loading protocol was applied with increasing axial force (3200?cycles, 175?N to 2250?N). Construct survival, acetabular fracture motion, and mode of failure were assessed. RESULTS:The median number of cycles needed until failure of the construct occurred was 2304?cycles (range, 2020 to 2675) in the plate fixation group and 3200?cycles (range, 3101 to 3200) for the screw fixation constructs (p?=?.003). With regard to energy absorbed until failure, the plate fixation group resisted to 1.57?×?106?N*cycles (range, 1.21?×?106 to 2.14?×?106) and the screw fixation group to 3.17?×?106?N*cycles (range, 2.92?×?106 to 3.17?×?106; p?=?.001). All plate fixation specimens failed with a break-out of the posterior-column screw in the quadrilateral wing of the anatomical plate within a maximum load of 1750?N while the screw fixation constructs all survived loading of at least 2100?N. Acetabular fracture gap motion, acetabular rim angle, and medial femoral head subluxation as measures of fracture displacement were all not different between the two groups (p?>?0.1). CONCLUSIONS:In this in vitro biomechanical study, screw-only fixation of an ACPHT acetabular fracture resulted in at least as good construct survival as seen for standard buttress plate fixation. Both methods resisted sufficiently to forces that would be expected under physiologic conditions.

Dataset Information

Locking Plates With Computationally Enhanced Screw Trajectories Provide Superior Biomechanical Fixation Stability of Complex Proximal Humerus Fractures.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets