Eu3+-Doped Electrospun Polyvinylidene Fluoride–Hexafluoropropylene/Graphene Oxide Multilayer Composite Nanofiber for the Fabrication of Flexible Pressure Sensors
Ontology highlight
ABSTRACT:
SUBMITTER: Fu G
PROVIDER: S-EPMC9280763 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Surface modification of fibers has attracted significant attention in different areas and applications. In this work, polyvinylidene fluoride (PVDF) cactus-like nanofibers were directly produced via electrospinning at a high relative humidity (RH) of 62%. The formation mechanism of the cactus structure was demonstrated. The effects of the RH on the fabrication of the cactus structure, crystalline phases, mechanical properties, hydrophobicity, and piezoelectric properties of the PVDF nanofibers were investigated. The results showed that the cactus-like nanofibers have a high crystallinity (ΔX c), and an outstanding water contact angle (WCA), as well as good electrical outputs. We believe that the PVDF cactus structure can be used in many applications such as energy harvesting and self-cleaning surfaces.
| S-EPMC9092256 | biostudies-literature
Project description:Electrospun polyvinylidene fluoride (PVDF) fiber mats with average fiber diameters (?200 nm, ?2000 nm) were fabricated by controlled electrospinning conditions. These fiber mats were polarized using a custom-made device to enhance the formation of the electret ?-phase ferroelectric property of the fibers by simultaneous uniaxial stretching of the fiber mat and heating the mat to the Curie temperature of the PVDF polymer in a strong electric field of 2.5 kV/cm. Scanning electron microscopy, Fourier transform infrared spectroscopy, thermal gravimetric analysis, differential scanning calorimetry and Brunauer-Emmett-Teller (BET) surface area analyses were performed to characterize both the internal and external morphologies of the fiber mat samples to study polarization-associated changes. MATLAB simulations revealed the changes in the paths of the electric fields and the magnetic flux inside the polarization field with inclusion of the ferroelectric fiber mats. Both polarized and unpolarized fiber mats were challenged as filters against NaCl particles with average particle diameters of about 150 nm using a TSI 8130 to study capture efficiencies and relative pressure drops. Twelve filter experiments were conducted on each sample at one month time intervals between experiments to evaluate the reduction of the polarization enhancement over time. The results showed negligible polarization loss for the 200-nm fiber sample. The polarized mats had the highest filter efficiencies and lowest pressure drops.
| S-EPMC5510728 | biostudies-literature
Project description:Piezoelectric polymers are promising energy materials for wearable and implantable applications for replacing bulky batteries in small and flexible electronics. Therefore, many research studies are focused on understanding the behavior of polymers at a molecular level and designing new polymer-based generators using polyvinylidene fluoride (PVDF). In this work, we investigated the influence of voltage polarity and ambient relative humidity in electrospinning of PVDF for energy-harvesting applications. A multitechnique approach combining microscopy and spectroscopy was used to study the content of the β-phase and piezoelectric properties of PVDF fibers. We shed new light on β-phase crystallization in electrospun PVDF and showed the enhanced piezoelectric response of the PVDF fiber-based generator produced with the negative voltage polarity at a relative humidity of 60%. Above all, we proved that not only crystallinity but also surface chemistry is crucial for improving piezoelectric performance in PVDF fibers. Controlling relative humidity and voltage polarity increased the d33 piezoelectric coefficient for PVDF fibers by more than three times and allowed us to generate a power density of 0.6 μW·cm-2 from PVDF membranes. This study showed that the electrospinning technique can be used as a single-step process for obtaining a vast spectrum of PVDF fibers exhibiting different physicochemical properties with β-phase crystallinity reaching up to 74%. The humidity and voltage polarity are critical factors in respect of chemistry of the material on piezoelectricity of PVDF fibers, which establishes a novel route to engineer materials for energy-harvesting and sensing applications.
| S-EPMC7497623 | biostudies-literature
Project description:In this work, we demonstrate selected optimization changes in the simple design of filtration masks to increase particle removal efficiency (PRE) and filter quality factor by combining experiments and numerical modeling. In particular, we focus on single-layer filters fabricated from uniform thickness fibers and double-layer filters consisting of a layer of highly permeable thick fibers as a support and a thin layer of filtering electrospun nanofibers. For single-layer filters, we demonstrate performance improvement in terms of the quality factor by optimizing the geometry of the composition. We show significantly better PRE performance for filters composed of micrometer-sized fibers covered by a thin layer of electrospun nanofibers. This work is motivated and carried out in collaboration with a targeted industrial development of selected melamine-based filter nano- and micromaterials.
| S-EPMC10496027 | biostudies-literature
Project description:Polyvinylidene fluoride (PVDF) blended with varying concentrations of titanium nanotubes (TNT) was electrospun to result in a nanocomposite filter media. Sandwich structures were obtained by depositing the electrospun fibers between polypropylene (PP) nonwoven sheets. The synthesized tubular TNT was confirmed for its morphology through a transmission electron microscope (TEM). The prepared filter media was analyzed through a scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier infrared spectroscopy (FTIR), and thermogravimetric analysis (TGA). The effectiveness of the filter media was evaluated through the zone of inhibition and antibacterial activity against E. coli and S. aureus. The Box-Behnken design is experimented with three-level variables, namely areal density of substrate (GSM), electrospinning time (hours), and concentration of TNT (wt%) for investigating the bacterial filtration efficiency through an Andersen sampler. Among other statistical tests (STATs), PVDF + 15 wt% TNT has a bacterial filtration efficiency of 99.88% providing greater potentials upon application for clean air management. It can be noted that the future application of this formulation could be efficient filtration of other microbes and could be used in facemasks to industrial-scale air filters. Graphical abstract.
| S-EPMC7955700 | biostudies-literature
Project description:Graphene (GE) is an emerging type of two-dimensional functional nanoparticle with a tunable passageway for oil molecules. Herein, polyvinylidene fluoride (PVDF)/GE composite membranes with controllable pore structure were fabricated with a simple non-solvent-induced phase separation method. The change of crystallinity and crystal structure (α, β, γ, etc.) generated is due to the addition of GE, which benefits the design of a suitable pore structure for oil channels. Meanwhile, the hydrophobicity and thermal stability of the composite membrane were obviously enhanced. With 3 wt % GE, the contact angle was 124.6°, which was increased greatly compared to that of the GE-0 sample. Moreover, the rate of the phase transition process was affected by the concentration of casting solution, temperature, and composition of the coagulation bath. For example, the composite membrane showed better oil-water separation properties when the coagulation bath was dioctyl phthalate. In particular, the oil flux and separation efficiencies were up to 2484.08 L/m2·h and 99.24%, respectively. Consequently, PVDF/GE composite membranes with excellent lipophilicity may have good prospects for oily wastewater treatment.
| S-EPMC9244927 | biostudies-literature
Project description:Pollutants and infectious diseases can spread through air with airborne droplets and aerosols. A respiratory mask can decrease the amount of pollutants we inhale and it can protect us from airborne diseases. With the onset of the COVID-19 pandemic, masks became an everyday item used by a lot of people around the world. As most of them are for a single use, the amount of non-recyclable waste increased dramatically. The plastic from which the masks are made pollutes the environment with various chemicals and microplastic. Here, we investigated the time- and size-dependent filtration efficiency (FE) of aerosols in the range of 25.9 to 685.4 nm of five different natural materials whose FE was enhanced using electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF) fibres. A scanning electron microscope (SEM) was used to determine the morphology and structure of the natural materials as well as the thickness of the PVDF fibres, while the phase of the electrospun fibres was determined by Raman spectroscopy. A thin layer of the electrospun PVDF fibres with the same grammage was sandwiched between two sheets of natural materials, and their FE increased up to 80%. By varying the grammature of the electrospun polymer, we tuned the FE of cotton from 82.6 to 99.9%. Thus, through the optimization of the grammage of the electrospun polymer, the amount of plastic used in the process can be minimized, while achieving sufficiently high FE.
| S-EPMC10054789 | biostudies-literature
Project description:Li-ion battery, separator, multicoreshell structure, thermal stability, long-term stability. A nanofibrous membrane with multiple cores of polyimide (PI) in the shell of polyvinylidene fluoride (PVdF) was prepared using a facile one-pot electrospinning technique with a single nozzle. Unique multicore-shell (MCS) structure of the electrospun composite fibers was obtained, which resulted from electrospinning a phase-separated polymer composite solution. Multiple PI core fibrils with high molecular orientation were well-embedded across the cross-section and contributed remarkable thermal stabilities to the MCS membrane. Thus, no outbreaks were found in its dimension and ionic resistance up to 200 and 250 °C, respectively. Moreover, the MCS membrane (at ~200 °C), as a lithium ion battery (LIB) separator, showed superior thermal and electrochemical stabilities compared with a widely used commercial separator (~120 °C). The average capacity decay rate of LIB for 500 cycles was calculated to be approximately 0.030 mAh/g/cycle. This value demonstrated exceptional long-term stability compared with commercial LIBs and with two other types (single core-shell and co-electrospun separators incorporating with functionalized TiO2) of PI/PVdF composite separators. The proper architecture and synergy effects of multiple PI nanofibrils as a thermally stable polymer in the PVdF shell as electrolyte compatible polymers are responsible for the superior thermal performance and long-term stability of the LIB.
| S-EPMC5105080 | biostudies-literature
Project description:In this study, micron-sized pored membranes, based on the co-polymer polyvinylidene difluoride hexafluoropropylene (PVdF-HFP) were prepared via phase inversion techniques. The aim of the approach was to find less harmful and less toxic solvents to fabricate such films. Therefore, the Hansen solubility approach was used to identify safer and less toxic organic solvents for the phase inversion process, relative to present solvent mixtures, based on acetone, dimethyl formamide, dimethyl acetamide or methanol. With this approach, it was possible to identify cyclopentanone, ethylene glycol and benzyl alcohol as suitable solvents for the membrane preparation process. Physicochemical and mechanical properties were analyzed and compared, which revealed a uniform membrane structure through the cross section. Differences were observed at the top surface, in dependence of both preparation approaches, which are described in detail.
| S-EPMC6418560 | biostudies-literature
Project description:This paper presents a facile and low-cost strategy for fabrication lysozyme-loaded mesoporous silica nanotubes (MSNTs) by using silk fibroin (SF) nanofiber templates. The "top-down method" was adopted to dissolve degummed silk in CaCl2/ formic acid (FA) solvent, and the solution containing SF nanofibrils was used for electrospinning to prepare SF nanofiber templates. As SF contains a large number of -OH, -NH2 and -COOH groups, the silica layer could be easily formed on its surface by the Söber sol-gel method without adding any surfactant or coupling agent. After calcination, the MSNTs were obtained with inner diameters about 200 nm, the wall thickness ranges from 37 ± 2 nm to 66 ± 3 nm and the Brunauer-Emmett-Teller (BET) specific surface area was up to 200.48 m2/g, the pore volume was 1.109 cm3/g. By loading lysozyme, the MSNTs exhibited relatively high drug encapsulation efficiency up to 31.82% and an excellent long-term sustained release in 360 h (15 days). These results suggest that the MSNTs with the hierarchical structure of mesoporous and macroporous will be a promising carrier for applications in biomacromolecular drug delivery systems.
| S-EPMC7923156 | biostudies-literature