Browse
Submit Data
Databases
API
Help

Dataset Information

28 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Water Sorption and Mechanical Properties of Cellulosic Derivative Fibers

ABSTRACT: In this study, water vapor sorption, desorption properties and tensile mechanical properties of four cellulosic fibers, cotton (C), flax (F), viscose (V) and cellulose acetate (CA), were determined. The sorption and desorption isotherms were modeled using the Park model, which allowed an accurate fitting on the whole range of water activity. This model corresponds to a multi-sorption mode dividing in three sorption modes: Langmuir sorption, Henry’s law and water clustering. Park’s parameters were compared for the sorption and desorption isotherms for each fiber. Regardless of the fiber, differences between sorption and desorption were obtained only for the Henry sorption. The obtained sorption properties were correlated to the accessibility and the amount of sorption sites and also to the crystallinity level of the fibers. It was found that V exhibited the highest water sorption capacity due to a higher hydroxyl groups accessibility and a low amorphous fraction, followed by F, C and CA. Results from tensile tests demonstrated that F and C fibers were more rigid, more resistant and less ductile than CA and V fibers due to a difference of microstructure of the fibers. Finally, the presence of water-sorbed molecules led to a decrease in tensile modulus due to plasticization phenomenon.

SUBMITTER: Simon M

PROVIDER: S-EPMC9322568 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Hydration and Sorption Properties of Raw and Milled Flax Fibers.

Project description:The physicochemical and hydration properties of mechanically modified flax fibers (FFs) were investigated herein. Raw flax fibers (FF-R) were ball-milled and sieved through mesh with various aperture sizes (420, 210, and 125 ?m) to achieve modified samples, denoted as FF-420, FF-210, and FF-125, respectively. The physicochemical and hydration properties of FF-R with variable particle sizes were characterized using several complementary techniques: microscopy (SEM), spectroscopy (FT-IR, XRD, and XPS), thermoanalytical methods (DSC and TGA), adsorption isotherms using gas/dye probes, and solvent swelling studies in liquid H2O. The hydration of FF biomass is governed by the micropore structure and availability of active surface sites, as revealed by the adsorption isotherm results and the TGA/DSC profiles of the hydrated samples. Gravimetric water swelling, water retention values, and vapor adsorption results provide further support that particle size reduction of FF-R upon milling parallels the changes in surface chemical and physicochemical properties relevant to adsorption/hydration in the modified FF materials. This study outlines a facile strategy for the valorization and tuning of the physicochemical properties of agricultural FF biomass via mechanical treatment for diverse applications in biomedicine, energy recovery, food, and biosorbents for environmental remediation.

| S-EPMC7098004 | biostudies-literature

The mechanical properties of single fibrin fibers.

Project description:Blood clots perform the mechanical task of stemming the flow of blood.To advance understanding and realistic modeling of blood clot behavior we determined the mechanical properties of the major structural component of blood clots, fibrin fibers.We used a combined atomic force microscopy (AFM)/fluorescence microscopy technique to determine key mechanical properties of single crosslinked and uncrosslinked fibrin fibers.Overall, full crosslinking renders fibers less extensible, stiffer, and less elastic than their uncrosslinked counterparts. All fibers showed stress relaxation behavior (time-dependent weakening) with a fast and a slow relaxation time, 2 and 52 s. In detail, crosslinked and uncrosslinked fibrin fibers can be stretched to 2.5 and 3.3 times their original length before rupturing. Crosslinking increased the stiffness of fibers by a factor of 2, as the total elastic modulus, E(0), increased from 3.9 to 8.0 MPa and the relaxed, elastic modulus, E(infinity), increased from 1.9 to 4.0 MPa upon crosslinking. Moreover, fibers stiffened with increasing strain (strain hardening), as E(0) increased by a factor of 1.9 (crosslinked) and 3.0 (uncrosslinked) at strains epsilon > 110%. At low strains, the portion of dissipated energy per stretch cycle was small (< 10%) for uncrosslinked fibers, but significant (approximately 40%) for crosslinked fibers. At strains > 100%, all fiber types dissipated about 70% of the input energy. We propose a molecular model to explain our data. Our single fiber data can now also be used to construct a realistic, mechanical model of a fibrin network.

| S-EPMC3010862 | biostudies-literature

Large datasets of water vapor sorption, mass diffusion immersed in water, hygroscopic expansion and mechanical properties of flax fibre/shape memory epoxy hygromorph composites.

Project description:This data article presents four experimental sets of results related to flax fibre composites with epoxy shape memory polymer matrix: water vapor absorption, mass diffusion immersed in water, hygroscopic expansion, mechanical properties. The water vapor absorption tests are described in raw data related to four types of laminates with weights measured at different relative humidity (0%, 9%, 33%, 44%,75%, 85% and 100%). The mass diffusion experiments are related to weights of immersed samples over time. The unidirectional composite hygroscopic expansion is also measured along the fibre longitude and transverse directions. The mechanical properties of flax composite at various temperatures (20°C, 40°C, 60°C, 80°C and 100°C) and humidity environments (50% and immersed) are also described. Load-displacement diagrams of the hygromorph composites are converted into stress-strain diagrams via a compliance calibration, from which the tensile moduli are extracted. The data presented in this article can provide a benchmark for the development of new models, or for the determination of other properties via post processing. The detailed interpretation of the data can be found in [1]. The data is available in the Mendeley Data repository at [2].

| S-EPMC9234088 | biostudies-literature

Solvent retention in electrospun fibers affects scaffold mechanical properties.

Project description:Electrospinning is a robust material fabrication method allowing for fine control of mechanical, chemical, and functional properties in scaffold manufacturing. Electrospun fiber scaffolds have gained prominence for their potential in a variety of applications such as tissue engineering and textile manufacturing, yet none have assessed the impact of solvent retention in fibers on the scaffold's mechanical properties. In this study, we hypothesized that retained electrospinning solvent acts as a plasticizer, and gradual solvent evaporation, by storing fibers in ambient air, will cause significant increases in electrospun fiber scaffold brittleness and stiffness, and a significant decrease in scaffold toughness. Thermogravimetric analysis indicated solvent retention in PGA, PLCL, and PET fibers, and not in PU and PCL fibers. Differential scanning calorimetry revealed that polymers that were electrospun below their glass transition temperature (T g ) retained solvent and polymers electrospun above T g did not. Young's moduli increased and yield strain decreased for solventretaining PGA, PLCL, and PET fiber scaffolds as solvent evaporated from the scaffolds over a period of 14 days. Toughness and failure strain decreased for PGA and PET scaffolds as solvent evaporated. No significant differences were observed in the mechanical properties of PU and PCL scaffolds that did not retain solvent. These observations highlight the need to consider solvent retention following electrospinning and its potential effects on scaffold mechanical properties.

| S-EPMC6482971 | biostudies-literature

Dry Spin Graphene Oxide Fibers: Mechanical/Electrical Properties and Microstructure Evolution.

Project description:Dry-spinning method is extensively employed in fiber industry, comparing to the counter-part of wet-spinning process, it has advantages of environmentally friendly, high yield rate and no need for purification. Here, we report the synthesis of graphene oxide (GO) fibers via dry spinning GO inks with extremely high concentrations. The proper rheology properties of such GO inks allow us to dry spin GO fiber directly. Various dry spinning conditions are investigated, and the relationship between mechanical performance and micro-structure of the obtained GO fiber are established. We found that the existence of larger GO liquid crystal domains does not necessarily result to higher mechanical properties, and it is because those large GO liquid crystal domains evolve into thick GO films during drying process and thus prevent the intimate compaction of the whole GOF and leave behind gaps. This is detrimental for the mechanical properties, and thus the dry spin GOF are much weaker than that of wet spin ones. Importantly, Barus effects, that generally arise during the melt spinning of polymers, were not observed, indicating that caution must be taken when classical polymer rheology theories are applied to investigate the dynamic behaviors of GO solution.

| S-EPMC6050277 | biostudies-literature

Local mechanical properties of electrospun fibers correlate to their internal nanostructure.

Project description:The properties of polymeric nanofibers can be tailored and enhanced by properly managing the structure of the polymer molecules at the nanoscale. Although electrospun polymer fibers are increasingly exploited in many technological applications, their internal nanostructure, determining their improved physical properties, is still poorly investigated and understood. Here, we unravel the internal structure of electrospun functional nanofibers made by prototype conjugated polymers. The unique features of near-field optical measurements are exploited to investigate the nanoscale spatial variation of the polymer density, evidencing the presence of a dense internal core embedded in a less dense polymeric shell. Interestingly, nanoscale mapping the fiber Young's modulus demonstrates that the dense core is stiffer than the polymeric, less dense shell. These findings are rationalized by developing a theoretical model and simulations of the polymer molecular structural evolution during the electrospinning process. This model predicts that the stretching of the polymer network induces a contraction of the network toward the jet center with a local increase of the polymer density, as observed in the solid structure. The found complex internal structure opens an interesting perspective for improving and tailoring the molecular morphology and multifunctional electronic and optical properties of polymer fibers.

| S-EPMC3834296 | biostudies-literature

Microbial production of megadalton titin yields fibers with advantageous mechanical properties.

Project description:Manmade high-performance polymers are typically non-biodegradable and derived from petroleum feedstock through energy intensive processes involving toxic solvents and byproducts. While engineered microbes have been used for renewable production of many small molecules, direct microbial synthesis of high-performance polymeric materials remains a major challenge. Here we engineer microbial production of megadalton muscle titin polymers yielding high-performance fibers that not only recapture highly desirable properties of natural titin (i.e., high damping capacity and mechanical recovery) but also exhibit high strength, toughness, and damping energy - outperforming many synthetic and natural polymers. Structural analyses and molecular modeling suggest these properties derive from unique inter-chain crystallization of folded immunoglobulin-like domains that resists inter-chain slippage while permitting intra-chain unfolding. These fibers have potential applications in areas from biomedicine to textiles, and the developed approach, coupled with the structure-function insights, promises to accelerate further innovation in microbial production of high-performance materials.

| S-EPMC8405620 | biostudies-literature

Bio-cleaning improves the mechanical properties of lignin-based carbon fibers.

Project description:Production of carbon fibers (CF) using renewable precursors has gained importance particularly in the last decade to reduce the dependency on conventional petroleum-based precursors. However, pre-treatment of these renewable precursors is still similar to that of conventional ones. Little work is put into greener pre-treatments and their effects on the end products. This work focuses on the use of bio-cleaned lignin as a green precursor to produce CF by electrospinning. Bio-cleaned kraft lignin A (Bio-KLA) and uncleaned kraft lignin A (KLA) were used to explore the effect of bio-cleaning on the diameter and mechanical properties of lignin fibers and CF. The effect of electric field, lignin-to-poly(ethylene oxide) (PEO) ratio and PEO molecular weight (MW) were evaluated by 33 factorial design using Design of Experiment (DOE). The electrospinning process parameters were optimized to obtain a balance between high elastic modulus and small fiber diameter. The model predicted optimized conditions were 50 kV m-1 electric field, 95/5 lignin-to-PEO ratio and 1000 kDa MW of PEO. When compared to KLA, Bio-KLA CFs showed a 2.7-fold increase in elastic modulus, 2-fold increase in tensile strength and 30% decrease in fiber diameter under the same optimum conditions. The results clearly show that bio-cleaning improved the mechanical properties of lignin derived CF.

| S-EPMC9054643 | biostudies-literature

Mechanical Properties of Ternary Composite from Waste Leather Fibers and Waste Polyamide Fibers with Acrylonitrile-Butadiene Rubber.

Project description:This study aimed to improve the mechanical properties of a composite material consisting of waste leather fibers (LF) and nitrile rubber (NBR) by partially replacing LF with waste polyamide fibers (PA). A ternary recycled composite NBR/LF/PA was produced by a simple mixing method and vulcanized by compression molding. The mechanical properties and dynamic mechanical properties of the composite were investigated in detail. The results showed that the mechanical properties of NBR/LF/PA increased with an increase in the PA ratio. The highest tensile strength value of NBR/LF/PA was found to have increased about 1.26 times, that is from 12.9 MPa of LF50 to 16.3 MPa of LF25PA25. Additionally, the ternary composite demonstrated high hysteresis loss, which was confirmed by dynamic mechanical analysis (DMA). The presence of PA formed a non-woven network that significantly enhanced the abrasion resistance of the composite compared to NBR/LF. The failure mechanism was also analyzed through the observation of the failure surface using scanning electron microscopy (SEM). These findings suggest that the utilization of both waste fiber products together is a sustainable approach to reducing fibrous waste while improving the qualities of recycled rubber composites.

| S-EPMC10255798 | biostudies-literature

High-Quality Cellulosic Fibers Engineered from Cotton-Elastane Textile Waste.

Project description:Even small amounts of elastane in cotton-elastane blended textiles can prevent fiber-to-fiber recycling strategies in textile recycling. Herein, the selective separation of elastane from cotton blends was addressed by the aminolytic degradation of the synthetic component. Polar aprotic solvents were tested as elastane solvents, but side reactions impeded aminolysis with some of them. Aminolysis of elastane succeeded under mild conditions using dimethyl sulfoxide in combination with diethylenetriamine and 1,5-diazabicyclo[4.3.0]non-5-ene as a cleaving agent and catalyst, respectively. The analysis of the nitrogen content in the recovered cellulose fraction demonstrated that 2 h of reaction at 80 °C reduced the elastane content to values lower than 0.08%. The characterization of the recovered cellulose showed that the applied conditions did not affect the macromolecular properties of cellulose and maintained a cellulose I crystal structure. Degraded elastane products were recovered through precipitation with water. Finally, the cellulosic component was turned into new fibers by dry-jet wet spinning with excellent tensile properties.

| S-EPMC10934812 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data