Browse
Submit Data
Databases
API
Help

Dataset Information

11 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Thickness dependence of the MoO(3) blocking layers on ZnO nanorod-inverted organic photovoltaic devices.

ABSTRACT: Organic solar cells based on vertically aligned zinc oxide nanorod arrays (ZNR) in an inverted structure of indium tin oxide (ITO)∕ZNR∕poly(3-hexylthiophene): (6,6)-phenyl C61 butyric acid methyl ester(P3HT:PCBM)∕MoO(3)∕aluminum(Al) were studied. We found that the optimum MoO(3) layer thickness condition of 20 nm, the MoO(3) can effectively decrease the probability of bimolecular recombination either at the Al interface or within the active layer itself. For this optimum condition we get a power conversion efficiency of 2.15%, a short-circuit current density of 9.02 mA∕cm(2), an open-circuit voltage of 0.55V, and a fill factor of 0.44 under 100 mW∕cm(2) irradiation. Our investigations also show that the highly crystallized ZNR can create short and continuous pathways for electron transport and increase the contact area between the ZNR and the organic materials.

SUBMITTER: Wang M

PROVIDER: S-EPMC3069983 | biostudies-other | 2011 Mar

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

11% Organic Photovoltaic Devices Based on PTB7-Th: PC<sub>71</sub>BM Photoactive Layers and Irradiation-Assisted ZnO Electron Transport Layers.

Project description:The enhancement of interfacial charge collection efficiency using buffer layers is a cost-effective way to improve the performance of organic photovoltaic devices (OPVs) because they are often universally applicable regardless of the active materials. However, the availability of high-performance buffer materials, which are solution-processable at low temperature, are limited and they often require burdensome additional surface modifications. Herein, high-performance ZnO based electron transporting layers (ETLs) for OPVs are developed with a novel g-ray-assisted solution process. Through careful formulation of the ZnO precursor and g-ray irradiation, the pre-formation of ZnO nanoparticles occurs in the precursor solutions, which enables the preparation of high quality ZnO films. The g-ray assisted ZnO (ZnO-G) films possess a remarkably low defect density compared to the conventionally prepared ZnO films. The low-defect ZnO-G films can improve charge extraction efficiency of ETL without any additional treatment. The power conversion efficiency (PCE) of the device using the ZnO-G ETLs is 11.09% with an open-circuit voltage (VOC), short-circuit current density ( JSC), and fill factor (FF) of 0.80 V, 19.54 mA cm-2, and 0.71, respectively, which is one of the best values among widely studied poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b']dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)]: [6,6]-phenyl-C71-butyric acid methyl ester (PTB7-Th:PC71BM)-based devices.

| S-EPMC6051392 | biostudies-literature

ZnO@TiO2 Core Shell Nanorod Arrays with Tailored Structural, Electrical, and Optical Properties for Photovoltaic Application.

Project description:ZnO has prominent electron transport and optical properties, beneficial for photovoltaic application, but its surface is prone to the formation of defects. To overcome this problem, we deposited nanostructured TiO2 thin film on ZnO nanorods to form a stable shell. ZnO nanorods synthesized by wet-chemistry are single crystals. Three different procedures for deposition of TiO2 were applied. The influence of preparation methods and parameters on the structure, morphology, electrical and optical properties were studied. Nanostructured TiO2 shells show different morphologies dependent on deposition methods: (1) separated nanoparticles (by pulsed laser deposition (PLD) in Ar), (2) a layer with nonhomogeneous thickness (by PLD in vacuum or DC reactive magnetron sputtering), and (3) a homogenous thin layer along the nanorods (by chemical deposition). Based on the structural study, we chose the preparation parameters to obtain an anatase structure of the TiO2 shell. Impedance spectroscopy shows pure electron conductivity that was considerably better in all the ZnO@TiO2 than in bare ZnO nanorods or TiO2 layers. The best conductivity among the studied samples and the lowest activation energy was observed for the sample with a chemically deposited TiO2 shell. Higher transparency in the visible part of spectrum was achieved for the sample with a homogenous TiO2 layer along the nanorods, then in the samples with a layer of varying thickness.

| S-EPMC6864808 | biostudies-literature

Low-Temperature Growth of ZnO Nanowires from Gravure-Printed ZnO Nanoparticle Seed Layers for Flexible Piezoelectric Devices.

Project description:Zinc oxide (ZnO) nanowires (NWs) are excellent candidates for the fabrication of energy harvesters, mechanical sensors, and piezotronic and piezophototronic devices. In order to integrate ZnO NWs into flexible devices, low-temperature fabrication methods are required that do not damage the plastic substrate. To date, the deposition of patterned ceramic thin films on flexible substrates is a difficult task to perform under vacuum-free conditions. Printing methods to deposit functional thin films offer many advantages, such as a low cost, low temperature, high throughput, and patterning at the same stage of deposition. Among printing techniques, gravure-based techniques are among the most attractive due to their ability to produce high quality results at high speeds and perform deposition over a large area. In this paper, we explore gravure printing as a cost-effective high-quality method to deposit thin ZnO seed layers on flexible polymer substrates. For the first time, we show that by following a chemical bath deposition (CBD) process, ZnO nanowires may be grown over gravure-printed ZnO nanoparticle seed layers. Piezo-response force microscopy (PFM) reveals the presence of a homogeneous distribution of Zn-polar domains in the NWs, and, by use of the data, the piezoelectric coefficient is estimated to be close to 4 pm/V. The overall results demonstrate that gravure printing is an appropriate method to deposit seed layers at a low temperature and to undertake the direct fabrication of flexible piezoelectric transducers that are based on ZnO nanowires. This work opens the possibility of manufacturing completely vacuum-free solution-based flexible piezoelectric devices.

| S-EPMC8226623 | biostudies-literature

Plasmon-enhanced Electrically Light-emitting from ZnO Nanorod Arrays/p-GaN Heterostructure Devices.

Project description:Effective and bright light-emitting-diodes (LEDs) have attracted broad interests in fundamental research and industrial application, especially on short wavelength LEDs. In this paper, a well aligned ZnO nanorod arrays grown on the p-GaN substrate to form a heterostructured light-emitting diode and Al nanoparticles (NPs) were decorated to improve the electroluminescence performance. More than 30-folds enhancement of the electroluminescence intensity was obtained compared with the device without Al NPs decoration. The investigation on the stable and transient photoluminescence spectraof the ZnO nanorod arrays before and after Al NPs decoration demonstrated that the metal surface plasmon resonance coupling with excitons of ZnO leads to the enhancement of the internal quantum efficiency (IQE). Our results provide aneffective approach to design novel optoelectronic devices such as light-emitting diodes and plasmonic nanolasers.

| S-EPMC4867586 | biostudies-other

MoO3 Thickness, Thermal Annealing and Solvent Annealing Effects on Inverted and Direct Polymer Photovoltaic Solar Cells

Project description:Several parameters of the fabrication process of inverted polymer bulk heterojunction solar cells based on titanium oxide as an electron selective layer and molybdenum oxide as a hole selective layer were tested in order to achieve efficient organic photovoltaic solar cells. Thermal annealing treatment is a common process to achieve optimum morphology, but it proved to be damageable for the performance of this kind of inverted solar cells. We demonstrate using Auger analysis combined with argon etching that diffusion of species occurs from the MoO3/Ag top layers into the active layer upon thermal annealing. In order to achieve efficient devices, the morphology of the bulk heterojunction was then manipulated using the solvent annealing technique as an alternative to thermal annealing. The influence of the MoO3 thickness was studied on inverted, as well as direct, structure. It appeared that only 1 nm-thick MoO3 is enough to exhibit highly efficient devices (PCE = 3.8%) and that increasing the thickness up to 15 nm does not change the device performance.

| S-EPMC5449054 | biostudies-literature

Dual Role of Graphene Quantum Dots in Active Layer of Inverted Bulk Heterojunction Organic Photovoltaic Devices.

Project description:Graphene quantum dots (GQDs) have shown broad application prospects in the field of photovoltaic devices due to their unique quantum confinement and edge effects. Here, we prepared GQDs by a photon-Fenton reaction as reported in our previous work, which has great advantage in the preparation scale. The photoelectric properties of the inverted hybrid solar cells based on poly(3-hexylthiophene) (P3HT):(6,6)-phenyl-C61 butyric acid methylester (PCBM):GQDs and P3HT:GQDs with different contents of GQDs as the active layers are demonstrated, as well as their morphology and structure by atomic force microscopy images. Then, the different roles of GQDs played in the ternary (P3HT:PCBM:GQDs) and binary (P3HT:GQDs) hybrid solar cells are studied systematically. The results indicate that the GQDs provide an efficient excition separation interface and charge transport channel for the improvement of hybrid solar cells. The preliminary exploration and elaboration of the role of GQDs in hybrid solar cells will be beneficial to understand the interfacial procedure and improve device performance in the future.

| S-EPMC6777089 | biostudies-literature

Role of additional PCBM layer between ZnO and photoactive layers in inverted bulk-heterojunction solar cells.

Project description:In order to induce greater light absorption, nano-patterning is often applied to the metal-oxide buffer layer in inverted bulk-heterojunction(BHJ) solar cells. However, current homogeneity was significantly disturbed at the interface, leading to an efficiency that was not fully optimized. In this work, an additional PC61BM layer was inserted between the ZnO ripple and the photoactive layer to enhance the electron extraction. The insertion of additional PC61BM layer provided substantial advantages in the operation of inverted BHJ solar cells; specifically, it enhanced current homogeneity and lowered accumulation and trapping of photogenerated charges at the ZnO interface. Inclusion of the additional PC61BM layer led to effective quenching of electron-hole recombination by a reduction in the number of accumulated charges at the surface of ZnO ripples. This resulted in a 16% increase in the efficiency of inverted BHJ solar cells to 7.7%, compared to solar cells without the additional PC61BM layer.

| S-EPMC3945486 | biostudies-literature

Enhanced Photovoltaic Properties of Perovskite Solar Cells by Employing Bathocuproine/Hydrophobic Polymer Films as Hole-Blocking/Electron-Transporting Interfacial Layers.

Project description:In this study, we improved the photovoltaic (PV) properties and storage stabilities of inverted perovskite solar cells (PVSCs) based on methylammonium lead iodide (MAPbI3) by employing bathocuproine (BCP)/poly(methyl methacrylate) (PMMA) and BCP/polyvinylpyrrolidone (PVP) as hole-blocking and electron-transporting interfacial layers. The architecture of the PVSCs was indium tin oxide/poly(3,4-ethylenedioxythiophene):polystyrenesulfonate/MAPbI3/[6,6]-phenyl-C61-butyric acid methyl ester/BCP based interfacial layer/Ag. The presence of PMMA and PVP affected the morphological stability of the BCP and MAPbI3 layers. The storage-stability of the BCP/PMMA-based PVSCs was enhanced significantly relative to that of the corresponding unmodified BCP-based PVSC. Moreover, the PV performance of the BCP/PVP-based PVSCs was enhanced when compared with that of the unmodified BCP-based PVSC. Thus, incorporating hydrophobic polymers into BCP-based hole-blocking/electron-transporting interfacial layers can improve the PV performance and storage stability of PVSCs.

| S-EPMC7795380 | biostudies-literature

Morphology-Preserving Sensitization of ZnO Nanorod Surfaces via Click-Chemistry.

Project description:Films of ZnO nanorods grown by chemical vapor deposition were functionalized with a chromophore in a stepwise process that preserves the surface morphology. In the first step, the ZnO nanorods were functionalized by exposure to prop-2-ynoic acid (propiolic acid) in vacuum, which did bind through the COOH group leading to a ZnO surface functionalized with ethyne moieties (ethyne/ZnO). In the second step, 9-(4-azidophenyl)-2,5-di-tert-butylperylene (DTBPe-Ph-N3) was reacted with the ethyne/ZnO surface via copper-catalyzed azide-alkyne click reaction (CuAAC) in solution to form the DTBPe-functionalized surface (DTBPe/ZnO). The ZnO morphology was preserved after each step, as demonstrated by scanning electron microscopy (SEM). Each step was probed by X-ray photoelectron spectroscopy (XPS), and transient absorption spectroscopy (TA) of the resulting DTBPe/ZnO surface shows interfacial electron transfer following visible light excitation. As expected, attempts to bind the reference compound 1-(4-(8,11-ditert-butylperylen-3-yl)-phenyl)-1H-1,2,3-triazole-4-carboxylic acid (DTBPe-Ph-Tz-COOH) directly from solution lead to etched surfaces (confirmed by SEM) and undefined binding modes (confirmed by TA).

| S-EPMC6007857 | biostudies-literature

One-pot crystalline ZnO nanorod growth in mineralizing peptide gels.

Project description:A new biomimetic approach for the one-pot synthesis of ZnO nanorods at neutral pH and room temperature is introduced; self-assembly of the ZnO-mineralzing peptides (CN111, PAGLQVGFAVEV-GGGSC) with Zn ions as bundles of nanofibers in the gel form leads to the growth of ZnO nanorod (NRD) inside the gel. This new nanomaterial synthesis may open a new strategy by using the catalytic peptide gels as nanomaterial reactors.

| S-EPMC6801111 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data