Ultra-high cooling rate utilizing thin film evaporation.
Ontology highlight
ABSTRACT:
SUBMITTER: Su F
PROVIDER: S-EPMC3460952 | biostudies-other | 2012 Sep
REPOSITORIES: biostudies-other
Similar Datasets
Project description:In present-day high-performance electronic components, the generated heat loads result in unacceptably high junction temperatures and reduced component lifetimes. Thermoelectric modules can, in principle, enhance heat removal and reduce the temperatures of such electronic devices. However, state-of-the-art bulk thermoelectric modules have a maximum cooling flux qmax of only about 10?W?cm(-2), while state-of-the art commercial thin-film modules have a qmax <100?W?cm(-2). Such flux values are insufficient for thermal management of modern high-power devices. Here we show that cooling fluxes of 258?W?cm(-2) can be achieved in thin-film Bi2Te3-based superlattice thermoelectric modules. These devices utilize a p-type Sb2Te3/Bi2Te3 superlattice and n-type ?-doped Bi2Te3-xSex, both of which are grown heteroepitaxially using metalorganic chemical vapour deposition. We anticipate that the demonstration of these high-cooling-flux modules will have far-reaching impacts in diverse applications, such as advanced computer processors, radio-frequency power devices, quantum cascade lasers and DNA micro-arrays.
| S-EPMC4735511 | biostudies-other
Project description:Metal oxide thin-films transistors (TFTs) produced from solution-based printing techniques can lead to large-area electronics with low cost. However, the performance of current printed devices is inferior to those from vacuum-based methods due to poor film uniformity induced by the "coffee-ring" effect. Here, we report a novel approach to print high-performance indium tin oxide (ITO)-based TFTs and logic inverters by taking advantage of such notorious effect. ITO has high electrical conductivity and is generally used as an electrode material. However, by reducing the film thickness down to nanometers scale, the carrier concentration of ITO can be effectively reduced to enable new applications as active channels in transistors. The ultrathin (~10-nm-thick) ITO film in the center of the coffee-ring worked as semiconducting channels, while the thick ITO ridges (>18-nm-thick) served as the contact electrodes. The fully inkjet-printed ITO TFTs exhibited a high saturation mobility of 34.9 cm2 V-1 s-1 and a low subthreshold swing of 105 mV dec-1. In addition, the devices exhibited excellent electrical stability under positive bias illumination stress (PBIS, ΔVth = 0.31 V) and negative bias illuminaiton stress (NBIS, ΔVth = -0.29 V) after 10,000 s voltage bias tests. More remarkably, fully printed n-type metal-oxide-semiconductor (NMOS) inverter based on ITO TFTs exhibited an extremely high gain of 181 at a low-supply voltage of 3 V, promising for advanced electronics applications.
| S-EPMC8333237 | biostudies-literature
Project description:High mobility channel thin-film-transistor (TFT) is crucial for both display and future generation integrated circuit. We report a new metal-oxide TFT that has an ultra-thin 4.5 nm SnO2 thickness for both active channel and source-drain regions, very high 147 cm(2)/Vs field-effect mobility, high ION/IOFF of 2.3 × 10(7), small 110 mV/dec sub-threshold slope, and a low VD of 2.5 V for low power operation. This mobility is already better than chemical-vapor-deposition grown multi-layers MoS2 TFT. From first principle quantum-mechanical calculation, the high mobility TFT is due to strongly overlapped orbitals.
| S-EPMC4705631 | biostudies-other
Project description:Performance enhancement of the two-phase flow boiling heat transfer process in microchannels through implementation of surface micro- and nanostructures has gained substantial interest in recent years. However, the reported results range widely from a decline to improvements in performance depending on the test conditions and fluid properties, without a consensus on the physical mechanisms responsible for the observed behavior. This gap in knowledge stems from a lack of understanding of the physics of surface structures interactions with microscale heat and mass transfer events involved in the microchannel flow boiling process. Here, using a novel measurement technique, the heat and mass transfer process is analyzed within surface structures with unprecedented detail. The local heat flux and dryout time scale are measured as the liquid wicks through surface structures and evaporates. The physics governing heat transfer enhancement on textured surfaces is explained by a deterministic model that involves three key parameters: the drying time scale of the liquid film wicking into the surface structures (τd), the heating length scale of the liquid film (δH) and the area fraction of the evaporating liquid film (Ar). It is shown that the model accurately predicts the optimum spacing between surface structures (i.e. pillars fabricated on the microchannel wall) in boiling of two fluids FC-72 and water with fundamentally different wicking characteristics.
| S-EPMC5356182 | biostudies-literature
Project description:Interfacial solar evaporation holds great promise to address the freshwater shortage. However, most interfacial solar evaporators are always filled with water throughout the evaporation process, thus bringing unavoidable heat loss. Herein, we propose a novel interfacial evaporation structure based on the micro-nano water film, which demonstrates significantly improved evaporation performance, as experimentally verified by polypyrrole- and polydopamine-coated polydimethylsiloxane sponge. The 2D evaporator based on the as-prepared sponge realizes an enhanced evaporation rate of 2.18 kg m-2 h-1 under 1 sun by fine-tuning the interfacial micro-nano water film. Then, a homemade device with an enhanced condensation function is engineered for outdoor clean water production. Throughout a continuous test for 40 days, this device demonstrates a high water production rate (WPR) of 15.9-19.4 kg kW-1 h-1 m-2. Based on the outdoor outcomes, we further establish a multi-objective model to assess the global WPR. It is predicted that a 1 m2 device can produce at most 7.8 kg of clean water per day, which could meet the daily drinking water needs of 3 people. Finally, this technology could greatly alleviate the current water and energy crisis through further large-scale applications.
| S-EPMC10516847 | biostudies-literature
Project description:Printing electronics has become increasingly prominent in the field of electronic engineering because this method is highly efficient at producing flexible, low-cost and large-scale thin-film transistors. However, TFTs are typically constructed with rigid insulating layers consisting of oxides and nitrides that are brittle and require high processing temperatures, which can cause a number of problems when used in printed flexible TFTs. In this study, we address these issues and demonstrate a method of producing inkjet-printed TFTs that include an ultra-thin polymeric dielectric layer produced by initiated chemical vapor deposition (iCVD) at room temperature and highly purified 99.9% semiconducting carbon nanotubes. Our integrated approach enables the production of flexible logic circuits consisting of CNT-TFTs on a polyethersulfone (PES) substrate that have a high mobility (up to 9.76?cm(2) V(-1) sec(-)1), a low operating voltage (less than 4?V), a high current on/off ratio (3?×?10(4)), and a total device yield of 90%. Thus, it should be emphasized that this study delineates a guideline for the feasibility of producing flexible CNT-TFT logic circuits with high performance based on a low-cost and simple fabrication process.
| S-EPMC4869014 | biostudies-literature
Project description:Herein long-term delivery of proteins from biodegradable thin film devices is demonstrated, where a nanostructured polymer membrane controls release. Protein was sealed between two poly(caprolactone) films, which generated the thin film devices. Protein release for 210 days was shown in vitro, and stable activity was established through 70 days with a model protein. These thin film devices present a promising delivery platform for biologic therapeutics, particularly for application in constrained spaces.
| S-EPMC3480309 | biostudies-literature
Project description:The utilization of organic devices as pressure-sensing elements in artificial intelligence and healthcare applications represents a fascinating opportunity for the next-generation electronic products. To satisfy the critical requirements of these promising applications, the low-cost construction of large-area ultra-sensitive organic pressure devices with outstanding flexibility is highly desired. Here we present flexible suspended gate organic thin-film transistors (SGOTFTs) as a model platform that enables ultra-sensitive pressure detection. More importantly, the unique device geometry of SGOTFTs allows the fine-tuning of their sensitivity by the suspended gate. An unprecedented sensitivity of 192?kPa(-1), a low limit-of-detection pressure of <0.5?Pa and a short response time of 10?ms were successfully realized, allowing the real-time detection of acoustic waves. These excellent sensing properties of SGOTFTs, together with their advantages of facile large-area fabrication and versatility in detecting various pressure signals, make SGOTFTs a powerful strategy for spatial pressure mapping in practical applications.
| S-EPMC4366495 | biostudies-literature
Project description:Extreme ultra-violet lithography (EUVL) is the leading-edge technology to produce advanced nanoelectronics. The further development of EUVL is heavily based on implementing the so-called high numerical aperture (NA) EUVL, which will enable even smaller pitches up to 8 nm half pitch (HP). In anticipation of this high NA technology, it is crucial to assess the readiness of the current resist materials for the high NA regime to comply with the demanding requirements of resolution, line-edge roughness, and sensitivity (RLS). The achievable tighter pitches require lower film thicknesses for both resist and underlying transfer layers. A concern that is tied to the thinning down is the potential change in resist properties and behavior due to the interaction with the underlayer. To increase the fundamental understanding of ultra-thin films for high NA EUVL, a method to investigate the interplay of reduced film thickness and different patterning-relevant underlayers is developed by looking at the glass transition temperature (Tg) of polymer-based resists. To minimize the ambiguity of the results due to resist additives (i.e., photoacid generator (PAG) and quencher), it was opted to move forward with polymer-only samples, the main component of the resist, at this stage of the investigation. By using dielectric response spectroscopy, the results obtained show that changing the protection group of the polymer, as well as altering the polymer film thickness impacts the dynamics of the polymer mobility, which can be assessed through the Tg of the system. Unexpectedly, changing the underlayer did not result in a clear change in the polymer mobility at the tested film thicknesses.
| S-EPMC7762983 | biostudies-literature
Project description:Metal-oxide thin-film transistors (TFT) fabricated by spray pyrolysis are of increasing interest because of its simple process and scalability. A bottleneck issue is to get a bubble-free and dense material. We studied the effect of ammonium acetate (AA) addition in the oxide precursor solution on the performance of spray-coated ZnO TFTs. AA acts as a stabilizer, which increases the solubility of the solution and enhances the film quality by reducing the defects. With AA addition in ZnO precursor, the films are coffee ring free with high mass density and better grain orientation. The ZnO TFT with AA exhibit a remarkable improvement of its device performance such as saturation mobility increasing from 5.12 to 41.53 cm2V-1s-1, the subthreshold swing decreasing from 340 to 162 mV/dec and on/off current ratio increasing from ~105 to 108. Additionally, the TFTs show excellent stability with a low threshold voltage shift of 0.1 V under gate bias stress. Therefore, the addition of AA is a promising approach to achieve high-performance ZnO TFTs for low-cost manufacturing of displays.
| S-EPMC7265479 | biostudies-literature