Electroacoustic response of 1-3 piezocomposite transducers for high power applications.
Ontology highlight
ABSTRACT:
SUBMITTER: Jae Lee H
PROVIDER: S-EPMC3537705 | biostudies-other | 2012 Dec
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The high power characteristics of various piezoelectric ceramics and 1-3 composites were investigated. In contrast to "hard" Pb(Zr,Ti)O(3), modified (Bi(0.5)Na(0.5))TiO(3) based ceramics were found to show a relatively linear electromechanical response under high drive conditions due to their high stability of mechanical quality factor. The effects of high drive field and duty cycle on the behavior of 1-3 composites were analyzed by varying active and passive components. Improved high power characteristics of 1-3 composites were achieved by selection of optimized composite components, with enhanced electromechanical efficiency and thermal stability under high drive conditions.
| S-EPMC3411559 | biostudies-other
Project description:IntroductionPulmonary vein isolation is the cornerstone of rhythm-control therapy for atrial fibrillation (AF). The very high-power, short-duration (vHPSD) radiofrequency (RF) ablation is a novel technology that favors resistive heating while decreasing the role of conductive heating. Our study aimed to evaluate the correlations between contact force (CF), power, impedance drop (ID), and temperature; and to assess their role in lesion formation with the vHPSD technique.MethodsConsecutive patients who underwent initial point-by-point RF catheter ablation for AF were enrolled in the study. The vHPSD ablation was performed applying 90 W for 4 s with an 8 ml/min irrigation rate.ResultsData from 85 patients [median age 65 (59-71) years, 34% female] were collected. The median procedure time, left atrial dwelling time, and fluoroscopy time were 70 (60-90) min, 49 (42-58) min, and 7 (5-11) min, respectively. The median RF time was 312 (237-365) sec. No steam pop nor major complications occurred. A total of 6,551 vHPSD RF points were analyzed. The median of CF, maximum temperature, and ID were 14 (10-21) g, 47.6 (45.1-50.4) °C, and 8 (6-10) Ohms, respectively. CF correlated significantly with the maximum temperature (p < 0.0001). A CF of 5 g and above was associated with a significantly higher temperature compared to those lesions with a CF below 5 grams (p < 0.0001). Bilateral first-pass isolation rate was 84%. The 6-month AF-recurrence rate was 7%.ConclusionThe maximum temperature and CF significantly correlate with each other during vHPSD applications. A CF ≥ 5 g leads to better tissue heating and thus might be more likely to result in good lesion formation, although this clinical study was unable to assess actual lesion sizes.
| S-EPMC9326019 | biostudies-literature
Project description:Birefringent materials-which are highly needed in high power laser systems-may be limited in usage due to the laser-induced damage threshold of traditional birefringent materials. This work reports here on all-glass metasurfaces, fabricated by angled etching through sacrificial metal nanoparticle (NP) etching masks, for generation of effective birefringence in the formed layer. As a result, a fused silica metasurface, monolithic to the underlying substrate, is demonstrated to exhibit a birefringence of 6.57° under 375 nm illumination. Full-wave analysis shows a good agreement with the measurement and presents potential paths forward to increasing the effective metasurface birefringence. This is the first demonstration, to the best of knowledge, of an etching technique to obtain the resulting tilted pillar-like nanofeatures. The anisotropy of the metasurface nanoelements along the two window in-plane major axes presents different effective paths for the two polarizations and thus generates birefringence in a nonbirefringent material. Additionally, the imparted anisotropy lends itself to manipulation of physical properties of the surface as well, with metasurface feature orientation suppressing water flow along one principal axis and giving rise to water flow steering capabilities.
| S-EPMC10460841 | biostudies-literature
Project description:Ultrafast lasers have become increasingly important as research tools in laboratories and commercial enterprises suggesting laser safety, personal protection and awareness become ever more important. Laser safety eyewear are typically rated by their optical densities (OD) over various spectral ranges, but these measurements are usually made using low power, large beam size, and continuous beam conditions. These measurement scenarios are vastly different than the high power, small beam size, and pulsed laser beam conditions where ultrafast lasers have extremely high peak powers and broad spectra due to the short pulse durations. Many solid-state lasers are also tunable over a broad wavelength range, further complicating the selection of adequate laser safety eyewear. Eighteen laser eyewear filter samples were tested under real-world conditions using a Ti:Sapphire regenerative amplifier with output pulses centered at 800 nm running from 2 Hz to 1 KHz repetition rate. The typical maximum peak laser irrandiance employed was ca. 3 TW/cm2 (800 nm wavelength, 450 uJ/pulse with 80 fs FWHM pulse duration) or less when damage occurred, depending on the sample. While many samples maintained their integrity under these test conditions, many plastic samples showed signs of failure which reduced their OD, in some cases transmitting 4 to 5 orders of magnitude higher than expected. In general, glass filters performed significantly better than plastic filters, exhibiting less physical damage to the substrate and less absorber degradation.
| S-EPMC6459187 | biostudies-literature
Project description:The Tendo Unit (TU) and GymAware (GA) are the two most frequently used linear transducers for assessing muscle power in older adults via the sit-to-stand (STS) test. Unlike TU, GA incorporates a sensor mechanism to correct for non-vertical movements, which may lead to systematic differences between devices. The aim of this study therefore was to compare GA to TU for measuring STS power in community-dwelling older adults. Community-dwelling adults (n = 51, aged ≥65 years, 61% female) completed a single chair stand, with peak power measured simultaneously using GA and TU. Participants also completed the pneumatic leg press, 8-Foot Up and Go (TUG) test, Short Physical Performance Battery (SPPB), and self-reported measures of physical function. Intraclass correlations (ICC) were used to assess agreement, and Pearson's correlations were used to assess correlations. The study protocol was prospectively registered on the Open Science Framework. In alignment with our pre-registered hypothesis, peak power demonstrated an ICC of 0.93 (95% CI: 0.88, 0.96). For secondary aims, both transducers showed a correlation greater than 0.8 compared to pneumatic leg press power. For physical performance outcomes, both TU and GA showed similar correlations, as hypothesized: SPPB (r = 0.29 for TU vs. 0.33 for GA), Chair Stands (r = -0.41 vs. -0.38), TUG Fast (r = -0.53 vs. -0.52), mobility questionnaire (r = 0.52 vs. 0.52) and physical function questionnaire (r = 0.44 vs. 0.43). GA and TU peak power showed a high degree of agreement and similar correlations with physical and self-reported performance measures, suggesting that both methods can be used for assessing STS power in older adults.
| S-EPMC11318872 | biostudies-literature
Project description:The performance of sensing surfaces highly relies on nanostructures to enhance their sensitivity and specificity. Herein, nanostructured zinc oxide (ZnO) thin films of various thicknesses were coated on glass and p-type silicon substrates using a sol-gel spin-coating technique. The deposited films were characterized for morphological, structural, and optoelectronic properties by high-resolution measurements. X-ray diffraction analyses revealed that the deposited films have a c-axis orientation and display peaks that refer to ZnO, which exhibits a hexagonal structure with a preferable plane orientation (002). The thicknesses of ZnO thin films prepared using 1, 3, 5, and 7 cycles were measured to be 40, 60, 100, and 200 nm, respectively. The increment in grain size of the thin film from 21 to 52 nm was noticed, when its thickness was increased from 40 to 200 nm, whereas the band gap value decreased from 3.282 to 3.268 eV. Band gap value of ZnO thin film with thickness of 200 nm at pH ranging from 2 to 10 reduces from 3.263eV to 3.200 eV. Furthermore, to evaluate the transducing capacity of the ZnO nanostructure, the refractive index, optoelectric constant, and bulk modulus were analyzed and correlated. The highest thickness (200 nm) of ZnO film, embedded with an interdigitated electrode that behaves as a pH-sensing electrode, could sense pH variations in the range of 2-10. It showed a highly sensitive response of 444 μAmM-1cm-2 with a linear regression of R2 =0.9304. The measured sensitivity of the developed device for pH per unit is 3.72μA/pH.
| S-EPMC4500498 | biostudies-literature
Project description:Wide-bandgap (WBG) material-based switching devices such as gallium nitride (GaN) high electron mobility transistors (HEMTs) and silicon carbide (SiC) metal-oxide-semiconductor field-effect transistors (MOSFETs) are considered very promising candidates for replacing conventional silicon (Si) MOSFETs for various advanced power conversion applications, mainly because of their capabilities of higher switching frequencies with less switching and conduction losses. However, to make the most of their advantages, it is crucial to understand the intrinsic differences between WBG- and Si-based switching devices and investigate effective means to safely, efficiently, and reliably utilize the WBG devices. This paper aims to provide engineers in the power engineering field a comprehensive understanding of WBG switching devices' driving requirements, especially for mid- to high-power applications. First, the characteristics and operating principles of WBG switching devices and their commercial products within specific voltage ranges are explored. Next, considerations regarding the design of driving circuits for WBG switching devices are addressed, and commercial drivers designed for WBG switching devices are explored. Lastly, a review on typical papers concerning driving technologies for WBG switching devices in mid- to high-power applications is presented.
| S-EPMC7826992 | biostudies-literature
Project description:In this paper, we introduce the exponentiated power generalized Weibull power series (EPGWPS) family of distributions, obtained by compounding the exponentiated power generalized Weibull and power series distributions. By construction, the new family contains a myriad of new flexible lifetime distributions having strong physical interpretations (lifetime system, biological studies…). We discuss the characteristics and properties of the EPGWPS family, including its probability density and hazard rate functions, quantiles, moments, incomplete moments, skewness and kurtosis. The main vocation of the EPGWPS family remains to be applied in a statistical setting, and data analysis in particular. In this regard, we explore the estimation of the model parameters by the maximum likelihood method, with accuracy supported by a detailed simulation study. Then, we apply it to two practical data sets, showing the applicability and competitiveness of the EPGWPS models in comparison to some other well-reputed models.
| S-EPMC7083325 | biostudies-literature
Project description:The effect of MnO(2) addition on the dielectric and piezoelectric properties of 0.4Pb(Mg(13)Nb(23))O(3)-0.25PbZrO(3)-0.35PbTiO(3) single crystals was investigated. Analogous to acceptor doping in "hard" Pb(Zr,Ti)O(3) based polycrystalline materials, the Mn doped crystals exhibited enhanced mechanical Q ( approximately 1050) with low dielectric loss ( approximately 0.2%), while maintaining ultrahigh electromechanical coupling k(33)>90%, inherent in domain engineered single crystals. The effect of acceptor doping was also evident in the build-up of an internal bias (E(i) approximately 1.6 kVcm), shown by a horizontal offset in the polarization-field behavior. Together with the relatively high usage temperature (T(R-T) approximately 140 degrees C), the Mn doped crystals are promising candidates for high power and broad bandwidth transducers.
| S-EPMC2682751 | biostudies-other
Project description:Terahertz (THz) technology has emerged for biomedical applications such as scanning, molecular spectroscopy, and medical imaging. Although a thorough assessment to predict potential concerns has to precede before practical utilization of THz source, the biological effect of THz radiation is not yet fully understood with scant related investigations. Here, we applied a femtosecond-terahertz (fs-THz) pulse to mouse skin to evaluate non-thermal effects of THz radiation. Analysis of the genome-wide expression profile in fs-THz-irradiated skin indicated that wound responses were predominantly mediated by transforming growth factor-beta (TGF-?) signaling pathways. We validated NF?B1- and Smad3/4-mediated transcriptional activation in fs-THz-irradiated skin by chromatin immunoprecipitation assay. Repeated fs-THz radiation delayed the closure of mouse skin punch wounds due to up-regulation of TGF-?. These findings suggest that fs-THz radiation initiate a wound-like signal in skin with increased expression of TGF-? and activation of its downstream target genes, which perturbs the wound healing process in vivo.
| S-EPMC3731731 | biostudies-literature