Concrete embedded dye-synthesized photovoltaic solar cell.
Ontology highlight
ABSTRACT:
SUBMITTER: Hosseini T
PROVIDER: S-EPMC3782884 | biostudies-other | 2013
REPOSITORIES: biostudies-other
Similar Datasets
Project description:At an elevated temperature of 90 °C, a chemical bath deposition using an aqueous solution of Zn(NO3)2·6H2O and (CH2)6N4 resulted in the formation of both nanoflowers and microrods of ZnO on F-doped SnO2 glass with a seed layer. The nanoflowers and microrods were sensitized with dyes for application to the photoelectrodes of dye-sensitized solar cells (DSSCs). By extending the growth time of ZnO, the formation of nanoflowers was reduced and the formation of microrods favored. As the growth time was increased from 4 to 6 and then to 8 h, the open circuit voltage (Voc) values of the DSSCs were increased, whilst the short circuit current (Jsc) values varied only slightly. Changes in the dye-loading amount, dark current, and electrochemical impedance were monitored and they revealed that the increase in Voc was found to be due to a retardation of the charge recombination between photoinjected electrons and I3- ions and resulted from a reduction in the surface area of ZnO microrods. A reduced surface area decreased the dye contents adsorbed on the ZnO microrods, and thereby decreased the light harvesting efficiency (LHE). An increase in the electron collection efficiency attributed to the suppressed charge recombination counteracted the decreased LHE, resulting in comparable Jsc values regardless of the growth time.
| S-EPMC6956303 | biostudies-literature
Project description:In this manuscript, a series of dye-sensitized solar cells (DSSCs) were fabricated as a function of post-processing temperature based on mesoporous CuO@Zn(Al)O-mixed metal oxides (MMO) in conjunction with dye N719 as the main light absorber; the proposed CuO@Zn(Al)O geometry was, in turn, attained using Zn/Al-layered double hydroxide (LDH) as a precursor via combination of co-precipitation and hydrothermal techniques. In particular, the dye loading amount onto the deposited mesoporous materials was anticipated via regression equation-based UV-Vis technique analysis, which evidently demonstrated a robust correlation along with the fabricated DSSCs power conversion efficiency. In detail, of the DSSCs assembled, CuO@MMO-550 exhibited short-circuit current (JSC) and open-circuit voltage (VOC) of 3.42 (mA/cm2) and 0.67 (V) which result in significant fill factor and power conversion efficiency of 0.55% and 1.24%, respectively. This could mainly be due to the relatively high surface area of 51.27 (m2/g) which in turn validates considerable dye loading amount of 0.246 (mM/cm-2).
| S-EPMC10005446 | biostudies-literature
Project description:Many researchers working on the development of Dye-sensitized solar cells (DSCs) continue to focus on the synthesis of photoanode materials with high surface area, along with high light scattering ability to enhance light harvesting efficiency (LHE). On the other hand, dye packing density, which can also affect the LHE significantly, is often overlooked. Solvothermally synthesized anatase TiO2 nanoparticles (SANP) were obtained by a new and simple approach using a mixed solvent, ethanol and acetic acid. SANP were applied as a photoanodes material in DSCs using a metal-free organic dye (D149) or organometallic dye (N719) dyes. The dye loading (packing density) was examined in term of the isoelectric point (IEP) and the contribution of this, in addition to light scattering effects were shown to control the devices photovoltaic efficiency of the devices; specifically when compared with ones employing commercially available TiO2 nanoparticles (either transparent or a bilayer structure with a transparent layer and a scattering one). SANP photoanodes sensitized with D149 dye were found to be optimised at 10 µm, yielding photovoltaic conversion efficiencies of 6.9%, superior to for transparent or transparent + scattering films from the commercial source (5.6% and 5.9%, respectively). Further to this, an efficiency of 7.7% PCE was achieved using a SANP photoanode sensitized with N719 dye, with 7.2% seen for the transparent photoanode and 7.9% with a scattering layer. The high efficiencies of devices based on of SANP photoanode are attributed to the high dye loading capability in addition to good light scattering. A further point of interest is that even with the increased reactivity of the surface towards dye adsorption, we did not observe any significant increase in recombination with the redox mediator, presumably due to this increased dye loading providing better shielding.
| S-EPMC7952064 | biostudies-literature
Project description:We report the fabrication and testing of dye sensitized solar cells (DSSC) based on tin oxide (SnO2) particles of average size ~20 nm. Fluorine-doped tin oxide (FTO) conducting glass substrates were treated with TiOx or TiCl4 precursor solutions to create a blocking layer before tape casting the SnO2 mesoporous anode. In addition, SnO2 photoelectrodes were treated with the same precursor solutions to deposit a TiO2 passivating layer covering the SnO2 particles. We found that the modification enhances the short circuit current, open-circuit voltage and fill factor, leading to nearly 2-fold increase in power conversion efficiency, from 1.48% without any treatment, to 2.85% achieved with TiCl4 treatment. The superior photovoltaic performance of the DSSCs assembled with modified photoanode is attributed to enhanced electron lifetime and suppression of electron recombination to the electrolyte, as confirmed by electrochemical impedance spectroscopy (EIS) carried out under dark condition. These results indicate that modification of the FTO and SnO2 anode by titania can play a major role in maximizing the photo conversion efficiency.
| S-EPMC4796906 | biostudies-literature
Project description:The performance of dye-sensitized solar cells (DSCs) critically depends on the efficiency of electron transport within the TiO2-dye-electrolyte interface. To improve the efficiency of the electron transfer the conventional structure of the working electrode (WE) based on TiO2 nanoparticles (NPs) was replaced with TiO2 nanotubes (NTs). Sol-gel method was used to prepare undoped and Nb-doped TiO2 NPs and TiO2 NTs. The crystallinity and morphology of the WEs were characterized using XRD, SEM and TEM techniques. XPS and PL measurements revealed a higher concentration of oxygen-related defects at the surface of NPs-based electrodes compared to that based on NTs. Replacement of the conventional NPs-based TiO2 WE with alternative led to a 15% increase in power conversion efficiency (PCE) of the DSCs. The effect is attributed to the more efficient transfer of charge carriers in the NTs-based electrodes due to lower defect concentration. The suggestion was confirmed experimentally by electrical impedance spectroscopy measurements when we observed the higher recombination resistance at the TiO2 NTs-electrolyte interface compared to that at the TiO2 NPs-electrolyte interface. Moreover, Nb-doping of the TiO2 structures yields an additional 14% PCE increase. The application of Nb-doped TiO2 NTs as photo-electrode enables the fabrication of a DSC with an efficiency of 8.1%, which is 35% higher than that of a cell using a TiO2 NPs. Finally, NTs-based DSCs have demonstrated a 65% increase in the PCE value, when light intensity was decreased from 1000 to 10 W/m2 making such kind device be promising alternative indoor PV applications when the intensity of incident light is low.
| S-EPMC7075133 | biostudies-literature
Project description:Cracking in Silicon solar cells is an important factor for the electrical power-loss of photovoltaic modules. Simple geometrical criteria identifying the amount of inactive cell areas depending on the position of cracks with respect to the main electric conductors have been proposed in the literature to predict worst case scenarios. Here we present an experimental study based on the electroluminescence (EL) technique showing that crack propagation in monocrystalline Silicon cells embedded in photovoltaic (PV) modules is a much more complex phenomenon. In spite of the very brittle nature of Silicon, due to the action of the encapsulating polymer and residual thermo-elastic stresses, cracked regions can recover the electric conductivity during mechanical unloading due to crack closure. During cyclic bending, fatigue degradation is reported. This pinpoints the importance of reducing cyclic stresses caused by vibrations due to transportation and use, in order to limit the effect of cracking in Silicon cells.
| S-EPMC3968460 | biostudies-other
Project description:BackgroundDye-sensitized solar cells (DSSCs) have garnered a lot of attention in recent years. The solar energy to power conversion efficiency of a DSSC is influenced by various components of the cell such as the dye, electrolyte, electrodes and additives among others leading to varying experimental configurations. A large number of metal-based and metal-free dye sensitizers have now been reported and tools using such data to indicate new directions for design and development are on the rise.DescriptionDSSCDB, the first of its kind dye-sensitized solar cell database, aims to provide users with up-to-date information from publications on the molecular structures of the dyes, experimental details and reported measurements (efficiencies and spectral properties) and thereby facilitate a comprehensive and critical evaluation of the data. Currently, the DSSCDB contains over 4000 experimental observations spanning multiple dye classes such as triphenylamines, carbazoles, coumarins, phenothiazines, ruthenium and porphyrins.ConclusionThe DSSCDB offers a web-based, comprehensive source of property data for dye sensitized solar cells. Access to the database is available through the following URL: www.dyedb.com .
| S-EPMC5882482 | biostudies-literature
Project description:Dye-sensitized solar cells (DSSCs) are one of the most versatile and low-cost solar cells. However, DSSCs are prone to low power conversion efficiency (PCE) compared to their counterparts, owing to their different synthesis parameters and process conditions. Therefore, designing efficient DSSCs and identifying the parameters that control the PCE of DSSCs are a critical tasks. We have collected data from hydrothermally synthesized DSSCs in the present work, published from 2005 to 2020. In line with publishing trends in the said period, we evaluate ZnO as a popular photoactive material for DSSC applications. We further analyzed the performance of hydrothermally synthesized ZnO DSSCs using different statistical techniques and provided some significant insights. We further applied the machine-learning technique with a decision tree algorithm to understand and discover the possible set of rules and heuristics that govern the morphology of the hydrothermally grown ZnO. In addition, we also employed supervised and unsupervised machine-learning models using conventional decision trees and classification and regression trees, respectively, to identify the dependence of the PCE of ZnO DSSCs on the different synthesis parameters. The reported work also evidences the PCE predictions of the ZnO DSSCs by using random forest and artificial neural network algorithms. The results substantiate that the random forest and artificial neural network algorithms successfully predict the PCE of the ZnO DSSCs with reasonable accuracy. Thus, we present a novel approach of applying statistical analysis and machine-learning algorithms to understand, discover, and predict the performance of DSSCs. We recommend extending the said know-how to other solar cells to identify rules and heuristics and experimentally realize highly efficient solar cells in shrinking manufacturing windows with a cost-effective approach.
| S-EPMC8582059 | biostudies-literature
Project description:Enhancement in the efficiency of a TiO2 dye-sensitized solar cell (DSSC) has been demonstrated by introducing ferromagnetic perovskite BiFeO3 and controlling the magnetic field, which induces two-dimensional material-like properties in the bulk of the TiO2-BiFeO3 DSSC (a 3-dimensional material). The effect of the concentration of BiFeO3 as well as the magnetization direction on the performance of the TiO2-BiFeO3 DSSC has been investigated. After magnetization, it was confirmed that the current density, efficiency, and open circuit voltage of the TiO2-BiFeO3 DSSC were increased. The observed phenomena have been explained in terms of the Hall effect which is responsible for the reduction of the degree of freedom of the electron movement resulting in the two-dimensional material-like properties in the bulk of the TiO2-BiFeO3 DSSC.
| S-EPMC9500914 | biostudies-literature
Project description:In order to enhance the photovoltaic performance of dye-sensitized solar cell (DSSC), a novel design is demonstrated by introducing rare-earth compound europium ion doped yttrium fluoride (YF₃:Eu³⁺) in TiO₂ film in the DSSC. As a conversion luminescence medium, YF₃:Eu³⁺ transfers ultraviolet light to visible light via down-conversion, and increases incident harvest and photocurrent of DSSC. As a p-type dopant, Eu³⁺ elevates the Fermi level of TiO₂ film and thus heightens photovoltage of the DSSC. The conversion luminescence and p-type doping effect are demonstrated by photoluminescence spectra and Mott-Schottky plots. When the ratio of YF₃:Eu³⁺/TiO₂ in the doping layer is optimized as 5 wt.%, the light-to-electric energy conversion efficiency of the DSSC reaches 7.74%, which is increased by 32% compared to that of the DSSC without YF₃:Eu³⁺ doping. Double functions of doped rare-earth compound provide a new route for enhancing the photovoltaic performance of solar cells.
| S-EPMC3690393 | biostudies-other