Printed wide-slot antenna design with bandwidth and gain enhancement on low-cost substrate.
Ontology highlight
ABSTRACT:
SUBMITTER: Samsuzzaman M
PROVIDER: S-EPMC3947929 | biostudies-other | 2014
REPOSITORIES: biostudies-other
Similar Datasets
Project description:In this paper, a dielectric resonator antenna (DRA) with high gain and wide impedance bandwidth for fifth-generation (5G) wireless communication applications is proposed. The dielectric resonator antenna is designed to operate at higher-order TE?15x mode to achieve high antenna gain, while a hollow cylinder at the center of the DRA is introduced to improve bandwidth by reducing the quality factor. The DRA is excited by a 50? microstrip line with a narrow aperture slot. The reflection coefficient, antenna gain, and radiation pattern of the proposed DRAs are analyzed using the commercially available full-wave electromagnetic simulation tool CST Microwave Studio (CST MWS). In order to verify the simulation results, the proposed antenna structures were fabricated and experimentally validated. Measured results of the fabricated prototypes show a 10-dB return loss impedance bandwidth of 10.7% (14.3-15.9GHz) and 16.1% (14.1-16.5 GHz) for DRA1 and DRA2, respectively, at the operating frequency of 15 GHz. The results show that the designed antenna structure can be used in the Internet of things (IoT) for device-to-device (D2D) communication in 5G systems.
| S-EPMC7038332 | biostudies-literature
Project description:A meandered-microstrip fed circular shaped monopole antenna loaded with vertical slots on a high dielectric material substrate (ε r = 15) is proposed in this paper. The performance criteria of the proposed antenna have been experimentally verified by fabricating a printed prototype. The experimental results show that the proposed antenna has achieved wider bandwidth with satisfactory gain by introducing meandered-microstrip feeding in assistant of partial ground plane. It is observed that, the -10 dB impedance bandwidth of the proposed antenna at lower band is 44.4% (600 MHz-1 GHz) and at upper band is 28% (2.25 GHz-2.95 GHz). The measured maximum gains of -1.18 dBi and 4.87 dBi with maximum radiation efficiencies have been observed at lower band and upper band, respectively. The antenna configuration and parametric study have been carried out with the help of commercially available computer-aided EM simulator, and a good accordance is perceived in between the simulated and measured results. The analysis of performance criteria and almost consistent radiation pattern make the proposed antenna a suitable candidate for UHF RFID, WiMAX, and WLAN applications.
| S-EPMC3958724 | biostudies-other
Project description:MXene, the new family of two-dimensional materials having numerous nanoscale layers, is being considered as a novel microwave absorption material. However, MXene/functionalized MXene-loaded polymer nanocomposites exhibit narrow reflection loss (RL) bandwidth (RL less than or equal to -10 dB). In order to enhance the microwave absorption bandwidth of MXene hybrid-matrix materials, for the first time, macroscopic design approach is carried out for TiO2-Ti3C2Tx MXene and Fe3O4@TiO2-Ti3C2Tx MXene hybrids through simulation. The simulated results indicate that use of pyramidal meta structure of MXene can significantly tune the RL bandwidth. For optimized MXene hybrid-matrix materials pyramid pattern, the bandwidth enhances to 3-18 GHz. Experimental RL value well matched with the simulated RL. On the other hand, the optimized Fe3O4@TiO2-Ti3C2Tx hybrid exhibits two specific absorption bandwidths (minimum RL value - -47 dB). Compared with other two-dimensional nanocomposites such as graphene or Fe3O4-graphene, MXene hybrid-matrix materials show better microwave absorption bandwidth in macroscopic pattern.
| S-EPMC7481728 | biostudies-literature
Project description:ObjectivesThe objective of this study was to test the ability to achieve, maintain, and subjectively benefit from extended high-frequency amplification in a real-world use scenario, with a device that restores audibility for frequencies up to 10 kHz.DesignA total of 78 participants (149 ears) with mild to moderately-severe sensorineural hearing loss completed one of two studies conducted across eight clinical sites. Participants were fitted with a light-driven contact hearing aid (the Earlens system) that directly drives the tympanic membrane, allowing extended high-frequency output and amplification with minimal acoustic feedback. Cambridge Method for Loudness Equalization 2 - High Frequency (CAM2)-prescribed gains for experienced users were used for initial fitting, and adjustments were made when required according to participant preferences for loudness and comfort or when measures of functional gain (FG) indicated that more or less gain was needed. Participants wore the devices for an extended period. Prescribed versus adjusted output and gain, frequency-specific FG, and self-perceived benefit assessed with the Abbreviated Profile of Hearing Aid Benefit, and a custom questionnaire were documented. Self-perceived benefit results were compared with those for unaided listening and to ratings with participants' own acoustic hearing aids.ResultsThe prescribed low-level insertion gain from 6 to 10 kHz averaged 53 dB across all ears, with a range from 26 to 86 dB. After adjustment, the gain from 6 to 10 kHz decreased to an average of 45 dB with a range from 16 to 86 dB. Measured FG averaged 39 dB from 6 to 10 kHz with a range from 11 to 62 dB. Abbreviated Profile of Hearing Aid Benefit results revealed a significant improvement in communication relative to unaided listening, averaging 28 to 32 percentage points for the background noise, reverberation, and ease of communication subscales. Relative to participants' own hearing aids, the subscales ease of communication and aversiveness showed small but significant improvements for Earlens ranging from 6 to 7 percentage points. For the custom satisfaction questionnaire, most participants rated the Earlens system as better than their own hearing aids in most situations.ConclusionsParticipants used and reported subjective benefit from the Earlens system. Most participants preferred slightly less gain at 6 to 10 kHz than prescribed for experienced users by CAM2, preferring similar gains to those prescribed for inexperienced users, but gains over the extended high frequencies were high relative to those that are currently available with acoustic hearing aids.
| S-EPMC6453763 | biostudies-literature
Project description:In this paper, a low cost 28 GHz Antenna-in-Package (AIP) for a 5G communication system is designed and investigated. The antenna is implemented on a low-cost FR4 substrate with a phase shift control integrated circuit, AnokiWave phasor integrated circuit (IC). The unit cell where the array antenna and IC are integrated in the same plate constructs a flexible phase array system. Using the AIP unit cell, the desired antenna array can be created, such as 2 × 8, 8 × 8 or 2 × 64 arrays. The study design proposed in this study is a 2 × 2 unit cell structure with dimensions of 18 mm × 14 mm × 0.71 mm. The return loss at a 10 dB bandwidth is 26.5-29.5 GHz while the peak gain of the unit cell achieved 14.4 dBi at 28 GHz.
| S-EPMC7569853 | biostudies-literature
Project description:A printed Bow-Tie slot antenna with loaded stub is proposed and the effects of changing the dimensions of the slot area, the stub and load sizes are considered in this paper. These parameters have a considerable effect on the antenna characteristics as well as its performance. An in-depth parametric study of these dimensions is presented. This paper proposes the necessary conditions for initial approximation of dimensions needed to design this antenna. In order to achieve the desired performance of the antenna fine tuning of all sizes of these parameters is required. The parametric studies used in this paper provide proper trends for initiation and tuning the design. A prototype of the antenna for 1.7GHz to 2.6GHz band is fabricated. Measurements conducted verify that the designed antenna has wideband characteristics with 50% bandwidth around the center frequency of 2.1GHz. Conducted measurements for reflection coefficient (S11) and radiation pattern also validate our simulation results.
| S-EPMC5256992 | biostudies-literature
Project description:This paper presents the design and realization of a compact ultra-wideband (UWB) antenna with a rectangular notch wireless area network (WLAN) band that has controllable notched bandwidth and center frequency. The UWB characteristics of the antenna are achieved by truncating the lower ends of the rectangular microstrip patch, and the notch characteristics are obtained by using electromagnetic bandgap (EBG) structures. EBGs consist of two rectangular metallic conductors loaded on the back of the radiator, which is connected to the patch by shorting pins. A rectangular notch at the WLAN band with high selectivity is realized by tuning the individual resonant frequencies of the EBGs and merging them. Furthermore, the results show that the bandwidth and frequency of the rectangular notch band could be controlled according to the on-demand rejection band applications. In the demonstration, the rectangular notch band was shifted to X-band satellite communication by tuning the EBG parameters. The simulated and measured results show that the proposed antenna has an operational bandwidth from 3.1-12.5 GHz for |S11| < -10 with a rectangular notch band from 5-6 GHz, thus rejecting WLAN band signals. The antenna also has additional advantages: the overall size of the compact antenna is 16 × 25 × 1.52 mm3 and it has stable gain and radiation patterns.
| S-EPMC7038389 | biostudies-literature
Project description:Efficient and reliable on-chip optical amplifiers and light sources would enable versatile integration of various active functionalities on the silicon platform. Although lasing on silicon has been demonstrated with semiconductors by using methods such as wafer bonding or molecular beam epitaxy, cost-effective mass production methods for CMOS-compatible active devices are still lacking. Here, we report ultra-high on-chip optical gain in erbium-based hybrid slot waveguides with a monolithic, CMOS-compatible and scalable atomic-layer deposition process. The unique layer-by-layer nature of atomic-layer deposition enables atomic scale engineering of the gain layer properties and straightforward integration with silicon integrated waveguides. We demonstrate up to 20.1?±?7.31?dB/cm and at least 52.4?±?13.8?dB/cm net modal and material gain per unit length, respectively, the highest performance achieved from erbium-based planar waveguides integrated on silicon. Our results show significant advances towards efficient on-chip amplification, opening a route to large-scale integration of various active functionalities on silicon.
| S-EPMC6347631 | biostudies-literature
Project description:A low-cost compact planar leaky-wave antenna (LWA) is proposed offering directive broadside radiation over a significantly wide bandwidth. The design is based on an annular metallic strip grating (MSG) configuration, placed on top of a dual-layer grounded dielectric substrate. This defines a new two-layer parallel-plate open waveguide, whose operational principles are accurately investigated. To assist in our antenna design, a method-of-moments dispersion analysis has been developed to characterize the relevant TM and TE modes of the perturbed guiding structure. By proper selection of the MSG for a fabricated prototype and its supporting dielectric layers as well as the practical TM antenna feed embedded in the bottom ground plane, far-field pencil-beam patterns are observed at broadside and over a wide frequency range, i.e., from 21.9?GHz to 23.9?GHz, defining a radiating percentage bandwidth of more than 8.5%. This can be explained by a dominantly excited TM mode, with low dispersion, employed to generate a two-sided far-field beam pattern which combines to produce a single beam at broadside over frequency. Some applications of this planar antenna include radar and satellite communications at microwave and millimeter-wave frequencies as well as future 5G communication devices and wireless power transmission systems.
| S-EPMC6288108 | biostudies-other
Project description:Phase-stable electromagnetic pulses in the THz frequency range offer several unique capabilities in time-resolved spectroscopy. However, the diversity of their application is limited by the covered spectral bandwidth. In particular, the upper frequency limit of photoconductive emitters - the most widespread technique in THz spectroscopy - reaches only up to 7?THz in the regular transmission mode due to absorption by infrared-active optical phonons. Here, we present ultrabroadband (extending up to 70?THz) THz emission from an Au-implanted Ge emitter that is compatible with mode-locked fibre lasers operating at wavelengths of 1.1 and 1.55??m with pulse repetition rates of 10 and 20?MHz, respectively. This result opens up the possibility for the development of compact THz photonic devices operating up to multi-THz frequencies that are compatible with Si CMOS technology.
| S-EPMC7052201 | biostudies-literature