Browse
Submit Data
Databases
API
Help

Dataset Information

5 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

The construction of an interfacial valve-based microfluidic chip for thermotaxis evaluation of human sperm.

ABSTRACT: Thermotaxis has been demonstrated to be an important criterion for sperm evaluation, yet clinical assessment of thermotaxis capacity is currently lacking. In this article, the on-chip thermotaxis evaluation of human sperm is presented for the first time using an interfacial valve-facilitated microfluidic device. The temperature gradient was established and accurately controlled by an external temperature gradient control system. The temperature gradient responsive sperm population was enriched into one of the branch channels with higher temperature setting and the non-responsive ones were evenly distributed into the two branch channels. We employed air-liquid interfacial valves to ensure stable isolation of the two branches, facilitating convenient manipulation of the entrapped sperm. With this device, thermotactic responses were observed in 5.7%-10.6% of the motile sperm moving through four temperature ranges (34.0-35.3 °C, 35.0-36.3 °C, 36.0-37.3 °C, and 37.0-38.3 °C, respectively). In conclusion, we have developed a new method for high throughput clinical evaluation of sperm thermotaxis and this method may allow other researchers to derive better IVF procedure.

SUBMITTER: Li Z

PROVIDER: S-EPMC3987097 | biostudies-other | 2014 Mar

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

A novel microfluidic chip-based sperm-sorting device constructed using design of experiment method.

Project description:Microfluidics is proposed as a technique for efficient sperm sorting, to achieve the ultimate goal of resolving infertility problems in livestock industry. Our study aimed to design a microfluidic sperm-sorting device (SSD) through a high-efficacy and cost- and time-effective fabrication process, by using COMSOL Multiphysics simulation and modeling software, and the design of experiment (DOE) method. The eight factors affecting SSD performance were established. The simulation was then run, and statistically significant factors were analyzed. Minitab16 was used to optimize the design modulus factor. By setting the statistical significance at p < 0.05, the factors affecting experimental structure were analyzed. At a desirability of 97.99, the optimal parameters for the microfluidic chip were: angle between sperm and medium inlet chambers (A = 43°), sperm inlet flow rate (B = 0.24 µL min-1), medium inlet flow rate (C = 0.34 µL min-1), and inlet and outlet chamber lengths (D = 5000 µm). These optima were then applied to microfluidics device construction. The device was produced using soft lithographic microfabrication techniques and tested on Holstein-Friesian bull sperm. The highest bull sperm-sorting performance for this microfluidic device prototype was 96%. The error between the simulation and the actual microfluidic device was 2.72%. Fluid viscosity ranges analysis-based simulations revealed acceptable fluid viscosity tolerances for the SSD. The simulation results revealed that the acceptable tolerance range for fluid viscosity was 0.00001-0.003 kg m-1 s-1. This optimally designed microfluidic chip-based SSD may be integrated into sperm x/y separation micro devices.

| S-EPMC7553928 | biostudies-literature

Construction and operation of a microrobot based on magnetotactic bacteria in a microfluidic chip.

Project description:Magnetotactic bacteria (MTB) are capable of swimming along magnetic field lines. This unique feature renders them suitable in the development of magnetic-guided, auto-propelled microrobots to serve in target molecule separation and detection, drug delivery, or target cell screening in a microfluidic chip. The biotechnology to couple these bacteria with functional loads to form microrobots is the critical point in its application. Although an immunoreaction approach to attach functional loads to intact MTB was suggested, details on its realization were hardly mentioned. In the current paper, MTB-microrobots were constructed by attaching 2 μm diameter microbeads to marine magnetotactic ovoid MO-1 cells through immunoreactions. These microrobots were controlled using a special control and tracking system. Experimental results prove that the attachment efficiency can be improved to ∼30% via an immunoreaction. The motility of the bacteria attached with different number of loads was also assessed. The results show that MTB can transport one load at a velocity of ∼21 μm/s and still move and survive for over 30 min. The control and tracking system is fully capable of directing and monitoring the movement of the MTB-microrobots. The rotating magnetic fields can stop the microrobots by trapping them as they swim within a circular field with a controllable size. The system has potential use in chemical analyses and medical diagnoses using biochips as well as in nano/microscale transport.

| S-EPMC3360722 | biostudies-other

A PMMA-Based Microfluidic Device for Human Sperm Evaluation and Screening on Swimming Capability and Swimming Persistence.

Project description:The selection of high-quality sperm is essential to the success of in vitro fertilization (IVF). As human cervical mucus has a high viscosity, without enough swimming persistence, human sperm clouds cannot arrive at the ampulla to fertilize the egg. In this study, we used swimming capability and motion characteristics that are known to be associated with fertilization ability to evaluate the quality of sperm. Here, a clinically applicable polymethyl methacrylate (PMMA)-based microdevice was designed and fabricated for sperm evaluation and screening for swimming capability and persistence in a viscous environment. In this study, we applied methylcellulose (MC) to mimic the natural properties of mucus in vivo to achieve the selection of motile sperm. Sperm motion was recorded by an inverted microscope. The statistical features were extracted and analyzed. Hundreds of sperm in two treated groups with different concentrations of MC and one control group with human tubal fluid (HTF) media were video recorded. This device can achieve a one-step procedure of high-quality sperm selection and achieve the quantitative evaluation of sperm swimming capability and persistence. Sperm with good swimming capability and persistence may be more suitable for fertilization in a viscous environment. This microdevice and methods could be used to guide the evaluation of sperm motility and screening in the future.

| S-EPMC7570091 | biostudies-literature

Cell Injection Millirobot Development and Evaluation in Microfluidic Chip.

Project description:We propose an innovative design of millirobot, which can achieve donor cell suction, delivery, and injection in a mammalian oocyte on a microfluidic chip. The millirobot body contains a hollow space that produces suction and ejection forces for the injection of cell nuclei using a nozzle at the tip of the robot. Specifically, a controller changes the hollow volume by balancing the magnetic and elastic forces of a membrane along with the motion of stages in the XY plane. A glass capillary attached to the tip of the robot contains a nozzle that is able to absorb and inject cell nuclei. The millirobot provides three degrees of freedom and generates micronewton forces. We demonstrate the effectiveness of the proposed millirobot through an experiment of the absorption and ejection of 20-µm particles from the nozzle using magnetic control in a microfluidic chip.

| S-EPMC6266326 | biostudies-literature

Enrichment of bovine X-sperm using microfluidic dielectrophoretic chip: A proof-of- concept study.

Project description:The microfluidic dielectrophoretic (MF-DEP) chip is a new, economical and readily-available technology that might be used to enrich X-sperm for increasing female offspring in dairy farms. In this study, we sought to develop an MF-DEP chip to enrich X bovine sperm. The MF-DEP chip was composed of an electrode attached to a glass slide and a microchannel made from polydimethylsiloxane. Sex-sorted sperm from flow cytometry were used to identify optimal electric field conditions while unsorted sperm were later tested for sorting efficiency. The results show that during dielectrophoresis some sperm attached to the electrode (called positive DEP; pDEP) whereas other moved away from the electrode (called negative DEP; nDEP). X and Y-sperm responded to dielectrophoresis differently depending on various factors such as buffers, voltages, and frequencies. We found that the condition 4 V 1 MHz significantly reduced (P < 0.05) the percentage of Y-sperm to nearly 30 and therefore enriched X-sperm. The sorting efficiency was dependent on buffer, bull, sorting cycle, flow rate, electrical voltage, and frequency. Notably, the best sorting buffer found in this experiment was the conducting buffer, but this buffer significantly reduced sperm viability and motility. Other sperm-friendly buffers, TRIS and mHTF, were also used, but could not enrich X-sperm. In conclusion, this is a proof of concept that the MF-DEP chip can be effectively used to enrich bovine X-sperm. However, more research must be performed particularly to find the best sorting buffer to effectively sex-sort sperm while providing high motility and sperm viability.

| S-EPMC7672294 | biostudies-literature

Effects of the microfluidic chip technique in sperm selection for intracytoplasmic sperm injection for unexplained infertility: a prospective, randomized controlled trial.

Project description:PurposeThe new-generation spermatozoon selection method, microfluidic technique called Fertile Chip® gives the chance to select spermatozoa with lower DNA fragmentation indexes. We aimed to determine the effect of microfluidic techniques for spermatozoon selection in ICSI treatment in patients with unexplained infertility.MethodsThis prospective randomized controlled study was conducted at a university hospital. One hundred twenty-two couples with unexplained infertility were included, in which 61 of them were treated with conventional swim-up techniques (control group) and another 61 with the microfluidic technique (study group) for spermatozoon selection in IVF treatment. The fertilization rates and the quality of embryos were the primary outcomes, and clinical pregnancy (CPR) and live birth rates (LBR) were the secondary outcomes of our study.ResultsCPR in the study group and control group were 48.3% and 44.8% (p = 0.35) and LBR were 38.3% and 36.2% (p = 0.48), respectively. The fertilization rates were similar (63.6% and 57.4%, p = 0.098). A total number of grade 1 embryos were significantly higher in microfluidic technique group than in control group (1.45 ± 1.62 vs. 0.83 ± 1.03, p = 0.01). There were more surplus top quality embryos leftover to freeze in the study group (0.71 ± 1.48 vs. 0.22 ± 0.69, p = 0.02).ConclusionOur study showed that the microfluidic technique does not change fertilization, CPR, and LBR during IVF treatment for couples with unexplained infertility. Despite the fact that the total number of grade 1 embryos after ICSI treatment and the surplus number of grade 1 embryos after embryo transfer were higher in the microfluidic technique group, the study was not powered to detect this difference.Trial registrationNCT02488434.

| S-EPMC6439003 | biostudies-literature

Rheotaxis-based sperm separation using a biomimicry microfluidic device.

Project description:Sperm selection is crucial to assisted reproduction, influencing the success rate of the treatment cycle and offspring health. However, in the current clinical sperm selection practices, bypassing almost all the natural selection barriers is a major concern. Here, we present a biomimicry microfluidic method, inspired by the anatomy of the female reproductive tract, that separates motile sperm based on their rheotaxis behavior to swim against the flow into low shear rate regions. The device includes micropocket geometries that recall the oval-shaped microstructures of the female fallopian tube to create shear protected zones for sperm separation. Clinical tests with human samples indicate that the device is capable of isolating viable and highly motile sperm based on their rheotaxis responses, resulting in a separation efficiency of 100%. The device presents an automated alternative for the current sperm selection practices in assisted reproduction.

| S-EPMC8443654 | biostudies-literature

Separation of tumor cells with dielectrophoresis-based microfluidic chip.

Project description:The present work demonstrates the use of a dielectrophoretic lab-on-a-chip device in effectively separating different cancer cells of epithelial origin for application in circulating tumor cell (CTC) identification. This study uses dielectrophoresis (DEP) to distinguish and separate MCF-7 human breast cancer cells from HCT-116 colorectal cancer cells. The DEP responses for each cell type were measured against AC electrical frequency changes in solutions of varying conductivities. Increasing the conductivity of the suspension directly correlated with an increasing frequency value for the first cross-over (no DEP force) point in the DEP spectra. Differences in the cross-over frequency for each cell type were leveraged to determine a frequency at which the two types of cell could be separated through DEP forces. Under a particular medium conductivity, different types of cells could have different DEP behaviors in a very narrow AC frequency band, demonstrating a high specificity of DEP. Using a microfluidic DEP sorter with optically transparent electrodes, MCF-7 and HCT-116 cells were successfully separated from each other under a 3.2 MHz frequency in a 0.1X PBS solution. Further experiments were conducted to characterize the separation efficiency (enrichment factor) by changing experimental parameters (AC frequency, voltage, and flow rate). This work has shown the high specificity of the described DEP cell sorter for distinguishing cells with similar characteristics for potential diagnostic applications through CTC enrichment.

| S-EPMC3555970 | biostudies-other

Sperm Selection and Embryo Development: A Comparison of the Density Gradient Centrifugation and Microfluidic Chip Sperm Preparation Methods in Patients with Astheno-Teratozoospermia.

Project description:In recent years, microfluidic chip-based sperm sorting has emerged as an alternative tool to centrifugation-based conventional techniques for in vitro fertilization. This prospective study aims to compare the effects of density gradient centrifugation and microfluidic chip sperm preparation methods on embryo development in patient populations with astheno-teratozoospermia. In the study, the semen samples of the patients were divided into two groups for preparation with either the microfluidic or density gradient methods. Selected spermatozoa were then used to fertilize mature sibling oocytes and the semen parameters and embryo development on days 3 and 5 were assessed. While the density gradient group was associated with a higher sperm concentration, motility (progressive and total) was significantly higher in the microfluidic chip group. No significant differences were observed in the fertilization rates or grade 1 (G1) and grade 2 (G2) proportions of the third-day embryos. Furthermore, while the proportions of the poor, fair and good blastocysts on day 5 did not differ significantly, excellent blastocysts (indicating high-quality embryos) were observed in a significantly higher proportion of the microfluidic chip group. When compared to the classical density gradient method, the microfluidic chip sperm preparation yielded sperm with higher motility and higher quality blastocysts at day 5; in patients with astheno-teratozoospermia.

| S-EPMC8466221 | biostudies-literature

Microscale Interfacial Polymerization on a Chip.

Project description:Forming hydrogels with precise geometries is challenging and mostly done using photopolymerization, which involves toxic chemicals, rinsing steps, solvents, and bulky optical equipment. Here, we introduce a new method for in situ formation of hydrogels with a well-defined geometry in a sealed microfluidic chip by interfacial polymerization. The geometry of the hydrogel is programmed by microfluidic design using capillary pinning structures and bringing into contact solutions containing hydrogel precursors from vicinal channels. The characteristics of the hydrogel (mesh size, molecular weight cut-off) can be readily adjusted. This method is compatible with capillary-driven microfluidics, fast, uses small volumes of reagents and samples, and does not require specific laboratory equipment. Our approach creates opportunities for filtration, hydrogel functionalization, and hydrogel-based assays, as exemplified by a rapid, compact competitive immunoassay that does not require a rinsing step.

| S-EPMC8597160 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data