Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Time Invariant Surface Roughness Evolution during Atmospheric Pressure Thin Film Depositions.

ABSTRACT: The evolution of thin film morphology during atmospheric pressure deposition has been studied utilizing Monte Carlo methods. Time invariant root-mean-squared roughness and local roughness morphology were both observed when employing a novel simulation parameter, modeling the effect of the experimental high pressure condition. This growth regime, where the surface roughness remains invariant after reaching a critical value, has not been classified by any existing universality class. An anti-shadowing growth mechanism responsible for this regime occurs when particles undergo binary collisions beneath the surface apexes. Hence, this mechanism is applicable when the mean free path of the depositing species is comparable to the amplitude of the surface features. Computationally this has been modeled by allowing particles to change direction at a specified height above the local film surface. This modification of the incoming flux trajectory consequently has a dramatic smoothening effect, and the resulting surfaces appear in agreement with recent experimental observations.

SUBMITTER: Merkh T

PROVIDER: S-EPMC4728611 | biostudies-other | 2016

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Atmospheric Pressure Microwave Plasma Jet for Organic Thin Film Deposition.

Project description:In this work, the potential of a microwave (MW)-induced atmospheric pressure plasma jet (APPJ) in film deposition of styrene and methyl methacrylate (MMA) precursors is investigated. Plasma properties during the deposition and resultant coating characteristics are studied. Optical emission spectroscopy (OES) results indicate a higher degree of monomer dissociation in the APPJ with increasing power and a carrier gas flow rate of up to 250 standard cubic centimeters per minute (sccm). Computational fluid dynamic (CFD) simulations demonstrate non-uniform monomer distribution near the substrate and the dependency of the deposition area on the monomer-containing gas flow rate. A non-homogeneous surface morphology and topography of the deposited coatings is also observed using atomic force microscopy (AFM) and SEM. Coating chemical analysis and wettability are studied by XPS and water contact angle (WCA), respectively. A lower monomer flow rate was found to result in a higher C-O/C-C ratio and a higher wettability of the deposited coatings.

| S-EPMC7077475 | biostudies-literature

Low Surface Roughness Graphene Oxide Film Reduced with Aluminum Film Deposited by Magnetron Sputtering.

Project description:Graphene film has wide applications in optoelectronic and photovoltaic devices. A novel and facile method was reported for the reduction of graphene oxide (GO) film by electron transfer and nascent hydrogen produced between aluminum (Al) film deposited by magnetron sputtering and hydrochloric acid (HCl) solution for only 5 min, significantly shorter than by other chemical reduction methods. The thickness of Al film was controlled utilizing a metal detection sensor. The effect of the thickness of Al film and the concentration of HCl solution during the reduction was explored. The optimal thickness of Al film was obtained by UV-Vis spectroscopy and electrical conductivity measurement of reduced GO film. Atomic force microscope images could show the continuous film clearly, which resulted from the overlap of GO flakes, the film had a relatively flat surface morphology, and the surface roughness reduced from 7.68 to 3.13 nm after the Al reduction. The film sheet resistance can be obviously reduced, and it reached 9.38 kΩ/sq with a high transmittance of 80% (at 550 nm). The mechanism of the GO film reduction by electron transfer and nascent hydrogen during the procedure was also proposed and analyzed.

| S-EPMC8227777 | biostudies-literature

Synthesis and Characterization of Nanofibrous Polyaniline Thin Film Prepared by Novel Atmospheric Pressure Plasma Polymerization Technique.

Project description:This work presents a study on the preparation of plasma-polymerized aniline (pPANI) nanofibers and nanoparticles by an intense plasma cloud type atmospheric pressure plasma jets (iPC-APPJ) device with a single bundle of three glass tubes. The nano size polymer was obtained at a sinusoidal wave with a peak value of 8 kV and a frequency of 26 kHz under ambient air. Discharge currents, photo-sensor amplifier, and optical emission spectrometer (OES) techniques were used to analyze the plasma produced from the iPC-APPJ device. Field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), gas chromatography-mass spectrometry (GC-MS), and gel permeation chromatography (GPC) techniques were used to analyze the pPANI. FE-SEM and TEM results show that pPANI has nanofibers, nanoparticles morphology, and polycrystalline characteristics. The FT-IR and GC-MS analysis show the characteristic polyaniline peaks with evidence that some quinone and benzene rings are broken by the discharge energy. GPC results show that pPANI has high molecular weight (Mw), about 533 kDa with 1.9 polydispersity index (PDI). This study contributes to a better understanding on the novel growth process and synthesis of uniform polyaniline nanofibers and nanoparticles with high molecular weights using the simple atmospheric pressure plasma polymerization technique.

| S-EPMC5456571 | biostudies-other

Bulk and surface recombination properties in thin film semiconductors with different surface treatments from time-resolved photoluminescence measurements.

Project description:The knowledge of minority carrier lifetime of a semiconductor is important for the assessment of its quality and design of electronic devices. Time-resolved photoluminescence (TRPL) measurements offer the possibility to extract effective lifetimes in the nanosecond range. However, it is difficult to discriminate between surface and bulk recombination and consequently the bulk properties of the semiconductor cannot be estimated reliably. Here we present an approach to constrain systematically the bulk and surface recombination parameters in semiconducting layers and reduces to finding the roots of a mathematical function. This method disentangles the bulk and surface recombination based on TRPL decay times of samples with different surface preparations. The technique is exemplarily applied to a CuInSe2 and a back-graded Cu(In,Ga)Se2 compound semiconductor, and upper and lower bounds for the recombination parameters and the mobility are obtained. Sets of calculated parameters are extracted and used as input for simulations of photoluminescence transients, yielding a good match to experimental data and validating the effectiveness of the methodology. A script for the simulation of TRPL transients is provided.

| S-EPMC6440953 | biostudies-literature

Real-time identification of the evolution of conducting nano-filaments in TiO2 thin film ReRAM.

Project description:Unipolar resistance switching (RS) in TiO2 thin films originates from the repeated formation and rupture of the Magnéli phase conducting filaments through repeated nano-scale phase transitions. By applying the Johnson-Mehl-Avrami (JMA) type kinetic model to the careful analysis on the evolution of transient current in a pulse-switching, it was possible to elucidate the material specific evolution of the Magnéli phase filament. This methodology was applied to the two types of TiO2 films grown by plasma-enhanced atomic layer deposition (PEALD) and sputtering. These two samples have structurally and electrically distinctive properties: PEALD film exhibited high variability in switching parameters and required an electroforming while sputtered film showed higher uniformity without distinct electroforming process. The JMA-type kinetic analysis of the RS behaviors revealed that the rejuvenation of the filament is accomplished by repeated one-dimensional nucleation followed by a two-dimensional growth in PEALD samples, whereas one-dimensional nucleation-free mechanism dominates in sputtered films.

| S-EPMC3853657 | biostudies-literature

Surface Termination Conversion during SrTiO3 Thin Film Growth Revealed by X-ray Photoelectron Spectroscopy.

Project description:Emerging electrical and magnetic properties of oxide interfaces are often dominated by the termination and stoichiometry of substrates and thin films, which depend critically on the growth conditions. Currently, these quantities have to be measured separately with different sophisticated techniques. This report will demonstrate that the analysis of angle dependent X-ray photoelectron intensity ratios provides a unique tool to determine both termination and stoichiometry simultaneously in a straightforward experiment. Fitting the experimental angle dependence with a simple analytical model directly yields both values. The model is calibrated through the determination of the termination of SrTiO3 single crystals after systematic pulsed laser deposition of sub-monolayer thin films of SrO. We then use the model to demonstrate that during homoepitaxial SrTiO3 growth, excess Sr cations are consumed in a self-organized surface termination conversion before cation defects are incorporated into the film. We show that this termination conversion results in insulating properties of interfaces between polar perovskites and SrTiO3 thin films. These insights about oxide thin film growth can be utilized for interface engineering of oxide heterostructures. In particular, they suggest a recipe for obtaining two-dimensional electron gases at thin film interfaces: SrTiO3 should be deposited slightly Ti-rich to conserve the TiO2-termination.

| S-EPMC4507138 | biostudies-literature

Real-Time Two-Dimensional Mapping of Relative Local Surface Temperatures with a Thin-Film Sensor Array.

Project description:Dynamic mapping of an object's local temperature distribution may offer valuable information for failure analysis, system control and improvement. In this letter we present a computerized measurement system which is equipped with a hybrid, low-noise mechanical-electrical multiplexer for real-time two-dimensional (2D) mapping of surface temperatures. We demonstrate the performance of the system on a device embedded with 32 pieces of built-in Cr-Pt thin-film thermocouples arranged in a 4 × 8 matrix. The system can display a continuous 2D mapping movie of relative temperatures with a time interval around 1 s. This technique may find applications in a variety of practical devices and systems.

| S-EPMC4969835 | biostudies-literature

A time-invariant principle of genome evolution.

Project description:Uncovering general principles of genome evolution that are time-invariant and that operate in germ and somatic cells has implications for genome-wide association studies (GWAS), gene therapy, and disease genomics. Here we investigate the relationship between structural alterations (e.g., insertions and deletions) and single-nucleotide substitutions by comparing the following genomes that diverged at different times across germ- and somatic-cell lineages: (i) the reference human and chimpanzee genome (in million years), (ii) the reference human and personal genomes (in tens of thousands of years), and (iii) structurally altered regions in cancer and genetically engineered cells (in days). At the species level, genes with structural alteration in nearby regions show increased single-nucleotide changes and tend to evolve faster. In personal genomes, the single-nucleotide substitution rate is higher near sites of structural alteration and decreases with increasing distance. In human cancer cell populations and in cells genetically engineered using zinc-finger nucleases, single-nucleotide changes occur frequently near sites of structural alterations. We present evidence that structural alteration induces single-nucleotide changes in nearby regions and discuss possible molecular mechanisms that contribute to this phenomenon. We propose that the low fidelity of nonreplicative error-prone repair polymerases, which are used during insertion or deletion, result in break-repair-induced single-nucleotide mutations in the vicinity of structural alteration. Thus, in the mutational landscape, structural alterations are linked to single-nucleotide changes across different time scales in both somatic- and germ-cell lineages. We discuss implications for genome evolution, GWAS, disease genomics, and gene therapy and emphasize the need to investigate both types of mutations within a single framework.

| S-EPMC2919972 | biostudies-literature

Evolution of the Surface Wettability of PET Polymer upon Treatment with an Atmospheric-Pressure Plasma Jet.

Project description:A useful technique for pre-treatment of polymers for improved biocompatibility is surface activation. A method for achieving optimal wettability at a minimal thermal load and unwanted modifications of the polymer properties is elaborated in this paper. Samples of polyethylene terephthalate polymer were exposed to an atmospheric-pressure plasma jet created by a high-impedance low-frequency discharge in wet argon. Different treatment times and distances from the end of the glowing discharge enabled detailed investigation of the evolution of surface activation. A rather fast saturation of the surface wettability over the area of the order of cm2 was observed upon direct treatment with the glowing discharge. At a distance of few mm from the glowing discharge, the activation was already two orders of magnitude lower. Further increase of the distance resulted in negligible surface effects. In the cases of a rapid activation, very sharp interphase between the activated and unaffected surface was observed and explained by peculiarities of high-impedance discharges sustained in argon with the presence of impurities of water vapor. Results obtained by X-ray photoelectron spectroscopy confirmed that the activation was a consequence of functionalization with oxygen functional groups.

| S-EPMC7023642 | biostudies-literature

Flexible/Bendable Acoustofluidics Based on Thin-Film Surface Acoustic Waves on Thin Aluminum Sheets.

Project description:In this paper, we explore the acoustofluidic performance of zinc oxide (ZnO) thin-film surface acoustic wave (SAW) devices fabricated on flexible and bendable thin aluminum (Al) foils/sheets with thicknesses from 50 to 1500 μm. Directional transport of fluids along these flexible/bendable surfaces offers potential applications for the next generation of microfluidic systems, wearable biosensors and soft robotic control. Theoretical calculations indicate that bending under strain levels up to 3000 με causes a small frequency shift and amplitude change (<0.3%) without degrading the acoustofluidic performance. Through systematic investigation of the effects of the Al sheet thickness on the microfluidic actuation performance for the bent devices, we identify the optimum thickness range to both maintain efficient microfluidic actuation and enable significant deformation of the substrate, providing a guide to design such devices. Finally, we demonstrate efficient liquid transportation across a wide range of substrate geometries including inclined, curved, vertical, inverted, and lateral positioned surfaces using a 200 μm thick Al sheet SAW device.

| S-EPMC8153544 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data