Browse
Submit Data
Databases
API
Help

Dataset Information

0 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Thermo-Mechanical Fatigue Crack Growth of RR1000.

ABSTRACT: Non-isothermal conditions during flight cycles have long led to the requirement for thermo-mechanical fatigue (TMF) evaluation of aerospace materials. However, the increased temperatures within the gas turbine engine have meant that the requirements for TMF testing now extend to disc alloys along with blade materials. As such, fatigue crack growth rates are required to be evaluated under non-isothermal conditions along with the development of a detailed understanding of related failure mechanisms. In the current work, a TMF crack growth testing method has been developed utilising induction heating and direct current potential drop techniques for polycrystalline nickel-based superalloys, such as RR1000. Results have shown that in-phase (IP) testing produces accelerated crack growth rates compared with out-of-phase (OOP) due to increased temperature at peak stress and therefore increased time dependent crack growth. The ordering of the crack growth rates is supported by detailed fractographic analysis which shows intergranular crack growth in IP test specimens, and transgranular crack growth in 90° OOP and 180° OOP tests. Isothermal tests have also been carried out for comparison of crack growth rates at the point of peak stress in the TMF cycles.

SUBMITTER: Pretty CJ

PROVIDER: S-EPMC5344579 | biostudies-other | 2017 Jan

REPOSITORIES: biostudies-other

ACCESS DATA

Json Xml

Similar Datasets

Comparison of Fatigue Properties and Fatigue Crack Growth Rates of Various Implantable Metals

Project description:The fatigue strength, effects of a notch on the fatigue strength, and fatigue crack growth rate of Ti-15Zr-4Nb-4Ta alloy were compared with those of other implantable metals. Zr, Nb, and Ta are important alloying elements for Ti alloys for attaining superior long-term corrosion resistance and biocompatibility. The highly biocompatible Ti-15Zr-4Nb-4Ta alloy exhibited an excellent balance between strength and ductility. Its notched tensile strength was much higher than that of a smooth specimen. The strength of 20% cold-worked commercially pure (C.P.) grade 4 Ti was close to that of Ti alloy. The tension-to-tension fatigue strength of an annealed Ti-15Zr-4Nb-4Ta rod at 107 cycles was approximately 740 MPa. The fatigue strength of this alloy was much improved by aging treatment after solution treatment. The fatigue strengths of C.P. grade 4 Ti and stainless steel were markedly improved by 20% cold working. The fatigue strength of Co-Cr-Mo alloy was markedly increased by hot forging. The notch fatigue strengths of 20% cold-worked C.P. grade 4 Ti, and annealed and aged Ti-15Zr-4Nb-4Ta, and annealed Ti-6Al-4V alloys were less than those of the smooth specimens. The fatigue crack growth rate of Ti-15Zr-4Nb-4Ta was the same as that of Ti-6Al-4V. The fatigue crack growth rate in 0.9% NaCl was the same as that in air. Stainless steel and Co-Cr-Mo-Ni-Fe alloy had a larger stress-intensity factor range (?K) than Ti alloy.

| S-EPMC5449063 | biostudies-literature

The dual role of martensitic transformation in fatigue crack growth.

Project description:Deformation-induced martensitic transformation (DIMT) has been used for designing high-performance alloys to prevent structural failure under static loads. Its effectiveness against fatigue, however, is unclear. This limits the application of DIMT for parts that are exposed to variable loads, although such scenarios are the rule and not the exception for structural failure. Here we reveal the dual role of DIMT in fatigue crack growth through in situ observations. Two antagonistic fatigue mechanisms mediated by DIMT are identified, namely, transformation-mediated crack arresting, which prevents crack growth, and transformation-mediated crack coalescence, which promotes crack growth. Both mechanisms are due to the hardness and brittleness of martensite as a transformation product, rather than to the actual transformation process itself. In fatigue crack growth, the prevalence of one mechanism over the other critically depends on the crack size and the mechanical stability of the parent austenite phase. Elucidating the two mechanisms and their interplay allows for the microstructure design and safe use of metastable alloys that experience fatigue loads. The findings also generally reveal how metastable alloy microstructures must be designed for materials to be fatigue-resistant.

| S-EPMC8892355 | biostudies-literature

Augmented finite-element method for arbitrary cracking and crack interaction in solids under thermo-mechanical loadings.

Project description:In this paper, a thermal-mechanical augmented finite-element method (TM-AFEM) has been proposed, implemented and validated for steady-state and transient, coupled thermal-mechanical analyses of complex materials with explicit consideration of arbitrary evolving cracks. The method permits the derivation of explicit, fully condensed thermal-mechanical equilibrium equations which are of mathematical exactness in the piece-wise linear sense. The method has been implemented with a 4-node quadrilateral two-dimensional (2D) element and a 4-node tetrahedron three-dimensional (3D) element. It has been demonstrated, through several numerical examples that the new TM-AFEM can provide significantly improved numerical accuracy and efficiency when dealing with crack propagation problems in 2D and 3D solids under coupled thermal-mechanical loading conditions. This article is part of the themed issue 'Multiscale modelling of the structural integrity of composite materials'.

| S-EPMC4901250 | biostudies-other

Fretting Fatigue with Cylindrical-On-Flat Contact: Crack Nucleation, Crack Path and Fatigue Life.

Project description:Fretting fatigue experiments and finite element analysis were carried out to investigate the influence of cylindrical-on-flat contact on crack nucleation, crack path and fatigue life of medium-carbon steel. The location of crack nucleation was predicted using the maximum shear stress range criterion and the maximum relative slip amplitude criterion. The prediction using the maximum relative slip amplitude criterion gave the better agreement with the experimental result, and should be used for the prediction of the location of crack nucleation. Crack openings under compressive bulk stresses were found in the fretting fatigues with flat-on-flat contact and cylindrical-on-flat contacts, i.e., fretting-contact-induced crack openings. The crack opening stress of specimen with flat-on-flat contact was lower than those of specimens with cylindrical-on-flat contacts, while that of specimen with 60-mm radius contact pad was lower than that of specimen with 15-mm radius contact pad. The fretting fatigue lives were estimated by integrating the fatigue crack growth curve from an initial propagating crack length to a critical crack length. The predictions of fretting fatigue life with consideration of crack opening were in good agreement with the experimental results.

| S-EPMC5459140 | biostudies-other

Influence of Retrogression Time on the Fatigue Crack Growth Behavior of a Modified AA7475 Aluminum Alloy.

Project description:This paper investigates the effect of retrogression time on the fatigue crack growth of a modified AA7475 aluminum alloy. Tests including tensile strength, fracture toughness, and fatigue limits were performed to understand the changes in properties with different retrogression procedures at 180 °C. The microstructure was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The findings indicated that as the retrogression time increased, the yield strength decreased from 508 MPa to 461 MPa, whereas the fracture toughness increased from 48 MPa√m to 63.5 MPa√m. The highest fracture toughness of 63.5 MPa√m was seen after 5 h of retrogression. The measured diameter of η' precipitates increased from 6.13 nm at the retrogression 1 h condition to 6.50 nm at the retrogression 5 h condition. Prolonged retrogression also increased the chance of crack initiation, with slower crack growth rate in the long transverse direction compared to the longitudinal direction. An empirical relationship was established between fracture toughness and the volume fraction of age-hardening precipitates, with increasing number density of precipitates seen with increasing retrogression time.

| S-EPMC10095606 | biostudies-literature

An Empirical Approach to Correlating Thermo-Mechanical Fatigue Behaviour of a Polycrystalline Ni-Base Superalloy.

Project description:Assessment of thermo-mechanical fatigue behaviour of the polycrystalline nickel alloy RR1000 reveals a significant effect of phase angle on fatigue life. The current paper explores two scenarios: the first where the mechanical strain range is held constant and comparisons of the fatigue life are made for different phase angle tests; and secondly, the difference between the behaviour of In-phase (IP) and -180° Out-Of-Phase (OOP) tests over a variety of applied strain ranges. It is shown that different lifing approaches are currently required for the two scenarios, with a mean stress based approach being more applicable in the first case, whereas a Basquin-type model proves more applicable in the second. However, it is also demonstrated that the crack propagation phase should also be considered in these types of tests for high strain ranges and projects that future modelling approaches should attempt to unify mean stress, stress range and a crack propagation phase.

| S-EPMC5452797 | biostudies-other

A Comparison Study of Machine Learning Based Algorithms for Fatigue Crack Growth Calculation.

Project description:The relationships between the fatigue crack growth rate ( d a / d N ) and stress intensity factor range ( Δ K ) are not always linear even in the Paris region. The stress ratio effects on fatigue crack growth rate are diverse in different materials. However, most existing fatigue crack growth models cannot handle these nonlinearities appropriately. The machine learning method provides a flexible approach to the modeling of fatigue crack growth because of its excellent nonlinear approximation and multivariable learning ability. In this paper, a fatigue crack growth calculation method is proposed based on three different machine learning algorithms (MLAs): extreme learning machine (ELM), radial basis function network (RBFN) and genetic algorithms optimized back propagation network (GABP). The MLA based method is validated using testing data of different materials. The three MLAs are compared with each other as well as the classical two-parameter model ( K * approach). The results show that the predictions of MLAs are superior to those of K * approach in accuracy and effectiveness, and the ELM based algorithms show overall the best agreement with the experimental data out of the three MLAs, for its global optimization and extrapolation ability.

| S-EPMC5459084 | biostudies-other

Corrosion-Fatigue Crack Growth in Plates: A Model Based on the Paris Law.

Project description:In this paper, a Paris law-based model is presented whereby crack propagation occurs under cyclic loading in air (fatigue) and in an aggressive environment (corrosion-fatigue) for the case of corner cracks (with a wide range of aspect ratios in the matter of the initial cracks) in finite-thickness plates of 316L austenitic stainless steel subjected to tension, bending, or combined (tension + bending) loading. Results show that the cracks tend during their growth towards a preferential propagation path, exhibiting aspect ratios slightly lower than unity only for the case of very shallow cracks, and diminishing as the crack grows (increasing the relative crack depth)-more intensely in the case of bending than in the case of tension (the mixed loading tension/bending representing an intermediate case). In addition, the crack aspect ratios during fatigue propagation evolution are lower in fatigue (in air) than in corrosion-fatigue (in aggressive environment).

| S-EPMC5506980 | biostudies-other

Explainable machine learning for precise fatigue crack tip detection.

Project description:Data-driven models based on deep learning have led to tremendous breakthroughs in classical computer vision tasks and have recently made their way into natural sciences. However, the absence of domain knowledge in their inherent design significantly hinders the understanding and acceptance of these models. Nevertheless, explainability is crucial to justify the use of deep learning tools in safety-relevant applications such as aircraft component design, service and inspection. In this work, we train convolutional neural networks for crack tip detection in fatigue crack growth experiments using full-field displacement data obtained by digital image correlation. For this, we introduce the novel architecture ParallelNets-a network which combines segmentation and regression of the crack tip coordinates-and compare it with a classical U-Net-based architecture. Aiming for explainability, we use the Grad-CAM interpretability method to visualize the neural attention of several models. Attention heatmaps show that ParallelNets is able to focus on physically relevant areas like the crack tip field, which explains its superior performance in terms of accuracy, robustness, and stability.

| S-EPMC9184622 | biostudies-literature

Influence of Experimental Parameters on Fatigue Crack Growth and Heat Build-Up in Rubber.

Project description:Loading parameters (frequency, amplitude ratio and waveform) are varied to determine their influence on fatigue crack growth in rubber. Up to three different rubber blends are investigated: one actual engineering material and two model materials. Fatigue crack growth curves and strain distributions of pure shear and faint waist pure shear samples are compared for a model material. Fatigue behavior is studied for three different frequencies (1 Hz, 3 Hz and 5 Hz). Amplitude ratio appears to be another important influence factor concerning fatigue crack growth in rubber. The beneficial effect of positive amplitude ratios (tensional loading conditions) is shown for different materials. However, fatigue crack growth is considerably increased for negative amplitude ratios (tensional-compressional loading conditions). Furthermore, the influence of the waveform is determined for three different waveform shapes. One is sinusoidal, and two have a square shape, including dwell periods and sinusoidal slopes. Special focus lies on heat build-up, which is substantial, especially for large loads, high frequencies and/or highly filled rubber blends. Plateau temperatures are determined for various loading conditions and rubber blends. A very simple linear relationship with dissipated energy per time and unit area is obtained. Results gathered with dynamic mechanical analyses show, likewise, a linear trend, but the heat build-up is very small, due to different sample geometries.

| S-EPMC5452735 | biostudies-other

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data