The Hardness and Strength Properties of WC-Co Composites.
Ontology highlight
ABSTRACT:
SUBMITTER: Armstrong RW
PROVIDER: S-EPMC5448685 | biostudies-other | 2011 Jul
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Metal matrix-impregnated diamond composites are widely used in diamond tool manufacturing. In order to satisfy the increasing engineering requirements, researchers have paid more and more attention to enhancing conventional metal matrices by applying novel methods. In this work, ZrO₂ nanoparticles were introduced into the WC-bronze matrix with and without diamond grits via hot pressing to improve the performance of conventional diamond composites. The effects of ZrO₂ nanoparticles on the microstructure, density, hardness, bending strength, and wear resistance of diamond composites were investigated. The results indicated that the hardness and relative density increased, while the bending strength decreased when the content of ZrO₂ nanoparticles increased. The grinding ratio of diamond composites increased significantly by 60% as a result of nano-ZrO₂ addition. The enhancement mechanism was discussed. Diamond composites showed the best overall properties with the addition of 1 wt % ZrO₂ nanoparticles, thus paving the way for further applications.
| S-EPMC5503043 | biostudies-other
Project description:Establishing processing routes for obtaining metal-matrix composites (MMCs) with uniformly-dispersed reinforcements is one of the main subjects in additively manufactured composite materials to achieve designed microstructures and mechanical properties. Here we report on the microstructural features of compositionally graded WC/Co-alloy composites additively manufactured by multi-beam laser directed energy deposition (multi-beam LDED). For tailoring microstructures of compositionally graded WC/Co-alloy composites with uniformly-dispersed reinforcements, the combinational method: the laser-beam defocus function in the multi-beam LDED system and granulated powder was attempted. By laser defocusing in the multi-beam LDED system, composites with uniformly-dispersed WC particles in Co alloy matrix was successfully obtained due to melting of Co bond in WC-12?wt.%Co granulated particles. It was found that the laser defocusing of multi-beam lasers affects temperature increase of flying powder during the laser focusing area, resulting in change of processing mode from melt-pool mode to thermal spray mode. The preferable property gradients in the WC/Co-alloy composites could be obtained by controlling the feeding rate of the powders and laser-beam defocus. These experimental results demonstrated the effectiveness of the laser-beam-defocus function in the multi-beam LDED system as a key factor for tailoring microstructures of additively-manufactured functionally graded MMCs with uniformly-dispersed reinforcements.
| S-EPMC7265354 | biostudies-literature
Project description:Nanodiamonds (ND) present a unique combination of desirable mechanical, functional, and chemical characteristics that are ideally suited for reinforcing and enhancing the wear resistance of carbide based materials. Tungsten carbide cobalt (WC-Co) matrix nanocomposites reinforced with varying amounts of ND (2 - 10 vol.%) were synthesized here by spark plasma sintering. The rapid thermal consolidation route enabled attainment of dense samples with a significant retention of the metastable diamond phase. NDs affected the microstructural evolution, chemistry, and mechanical properties of WC-Co. Macroscale reciprocating pin-on-disk tests were conducted to assess wear behavior under conditions relevant to service environments, e.g., high cycles and high contact pressure. Microscale tribological properties were assessed using microscratch tests in order to investigate the intrinsic effects of ND on the localized mechanical and tribological response of WC-Co-ND composites. The incorporation of 10 vol.% ND enhanced wear resistance at both the micro- and macroscale, by 28% and 35%, respectively.
| S-EPMC5539160 | biostudies-literature
Project description:A microarray analysis of wheat grain hardness Keywords: Cultivar Comparison
2006-07-25 | GSE5369 | GEO
Project description:(Ti,Zr)C powder was sintered with WC-Co following an industrial process, including an isotherm at 1410 °C. A series of interrupted sintering trials was performed with the aim of studying the sintering behavior and the microstructural evolution during both solid-state and liquid-state sintering. Reference samples, using the same elemental compositions but with the starting components TiC and ZrC instead of (Ti,Zr)C, were also sintered. The microstructure was investigated using scanning electron microscopy and energy dispersive X-ray spectroscopy. It is found that the (Ti,Zr)C phase decomposes into Ti-rich and Zr-rich nano-scale lamellae before the liquid-state of the sintering initiates. The final microstructure consists of the binder and WC as well as two different γ phases, rich in either Ti (γ₁) or Zr (γ₂). The γ₂ phase grains have a core-shell structure with a (Ti,Zr)C core following the full sintering cycle. The major differences observed in (Ti,Zr)C with respect to the reference samples after the full sintering cycle were the referred core-shell structure and the carbide grain sizes; additionally, the microstructural evolution during sintering differs. The grain size of carbides (WC, γ₁, and γ₂) is about 10% smaller in WC-(Ti,Zr)C-Co than WC-TiC-ZrC-Co. The shrinkage behavior and hardness of both composites are reported and discussed.
| S-EPMC5344544 | biostudies-other
Project description:Graphene has been regarded as one of the most promising two-dimensional nanomaterials. Even so, graphene was still faced with several key issues such as impedance mismatching and narrow bandwidth, which have hindered the practical applications of graphene-based nanocomposites in the field of microwave absorption materials. Herein, a series of Si-modified rGO@Fe3O4 composites were investigated and fabricated by a simple method. On one hand, the degree of defects in graphene carbon could be tuned by different silane coupling reagents, which were beneficial to enhancing the dielectric loss. On the other hand, the spherical Fe3O4 nanoparticles provided the magnetic loss resonance, which contributed to controlling the impedance matching. Subsequently, the electromagnetic absorption (EMA) properties of Si-modified rGO@Fe3O4 composites with poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) were investigated in this work. As a result, the Si(2)-rGO@Fe3O4/PVDF-co-HFP composite exhibited the excellent EMA performance in the range of 2-18 GHz. The maximum reflection loss (RLmax) reached -32.1 dB at 3.68 GHz at the thickness of 7 mm and the effective absorption frequency bandwidth for reflection loss (RL) below -10 dB was 4.8 GHz at the thickness of 2 mm. Furthermore, the enhanced absorption mechanism revealed that the high-efficiency absorption performance of Si(2)-rGO@Fe3O4/PVDF-co-HFP composite was attributed to the interference absorption (quarter-wave matching model) and the synergistic effects between Si(2)-rGO@Fe3O4 and PVDF-co-HFP. This work provides a potential strategy for the fabrication of the high-performance EMA materials.
| S-EPMC7079640 | biostudies-literature
Project description:To test the impact of preheating (25, 37, 54, or 68 °C) of TetricEvoCeram (TEC), FiltekSupremeXT (FSXT), and Venus (V) on flexural strength (FS), shear bond strength (SBS) and interfacial tension (IFT). FS was tested with TEC and FSXT. For SBS, glass-ceramic and human dentin substrate were fabricated and luted with the preheated resin composite (RC). SBSs of 1500 thermal cycled specimens were measured. For IFT, glass slides covered with the non-polymerized RC were prepared and contact angles were measured. Data were analyzed using 2/1-way ANOVA with Scheffé-test, and t-test (p < 0.05). Preheated TEC (37-68 °C) showed higher FS compared to the control-group (25 °C) (p < 0.001). FSXT presented higher FS than TEC (p < 0.001). For SBS to dentin higher values for FSXT than TEC were found. The preheating temperature showed no impact on SBS to dentin. SBS to glass-ceramic revealed a positive influence of temperature for TEC 25-68 °C (p = 0.015). TEC showed higher values than V and FSXT (p < 0.001). IFT values increased with the preheating temperature. A significant difference could be observed in every RC group between 25 and 68 °C (p < 0.001).
| S-EPMC5456469 | biostudies-other
Project description:To enhance the strength-to-weight ratio of a material, one may try to either improve the strength or lower the density, or both. The lightest solid materials have a density in the range of 1,000 kg/m(3); only cellular materials, such as technical foams, can reach considerably lower values. However, compared with corresponding bulk materials, their specific strength generally is significantly lower. Cellular topologies may be divided into bending- and stretching-dominated ones. Technical foams are structured randomly and behave in a bending-dominated way, which is less weight efficient, with respect to strength, than stretching-dominated behavior, such as in regular braced frameworks. Cancellous bone and other natural cellular solids have an optimized architecture. Their basic material is structured hierarchically and consists of nanometer-size elements, providing a benefit from size effects in the material strength. Designing cellular materials with a specific microarchitecture would allow one to exploit the structural advantages of stretching-dominated constructions as well as size-dependent strengthening effects. In this paper, we demonstrate that such materials may be fabricated. Applying 3D laser lithography, we produced and characterized micro-truss and -shell structures made from alumina-polymer composite. Size-dependent strengthening of alumina shells has been observed, particularly when applied with a characteristic thickness below 100 nm. The presented artificial cellular materials reach compressive strengths up to 280 MPa with densities well below 1,000 kg/m(3).
| S-EPMC3932926 | biostudies-literature
Project description:Because of their high thermal conductivity, good corrosion resistance, and great mechanical qualities, copper matrix composites are appealing materials utilized in a variety of industries. This study investigates the mechanical properties of copper-graphite (Cu-Gr) matrix composites reinforced with silicon carbide (SiC) and tungsten carbide (WC) particles by hot pressing using powder metallurgy method. The goal is to investigate the influence of the reinforcement ratio on the mechanical characteristics of copper composite materials generated (density, hardness, flexural strength, and wear resistance). SEM, EDS, and X-RD analysis were used to perform metallographic examinations. The highest relative density with a value of 98.558% was determined in the C3 sample. The findings revealed that when the reinforcement ratio was raised, the hardness rose. The highest hardness value was observed in the C6 sample with an increase of 12.52%. Sample C4 (with the lowest SiC and WC particles ratio) had the highest bending stress (233.18 MPa). Bending stress increased by 35.56% compared to the C1 sample. The lowest specific wear rates were found in the C4 sample, with a decrease of 82.57% compared to the C1 sample. The lowest wear rate (6.853 × 10-7 mm3/Nm) also occurred in the C4 sample. The microstructural analysis showed that the hybrid reinforcement particles exhibited a homogeneous distribution in the copper matrix. X-RD analysis showed that there was no intermediate reaction between the parent matrix and the hybrid reinforcements. A good interfacial bond was observed between the matrix structure and the hybrid reinforcements. The motivation of this research was to utilise the advantages of the unique features of SiC-WC hybrid particles to improve the performance of newly developed Cu-6Gr composites for wear-resistance applications.
| S-EPMC9268748 | biostudies-literature
Project description:Sand-casting is a well established primary process for manufacturing various parts of A356 alloy. However, the quality of the casting is adversely affected by the change in the magnitude of the control variables. For instance, a larger magnitude of pouring velocity induces a drop effect and a lower velocity increases the likelihood of cold-shut and mis-run types of defects. Similarly, a high pouring temperature causes the formation of hot tears, whereas a low temperature is a source of premature solidification. Likewise, a higher moisture content yields microcracks (due to gas shrinkages) in the casting and a lower moisture content results in the poor strength of the mold. Therefore, the appropriate selection of control variables is essential to ensure quality manufactured products. The empirical relations could provide valuable guidance in this regard. Additionally, although the casting process was optimized for A356 alloy, it was mostly done for a single response. Therefore, this paper aimed to formulate empirical relations for the contradictory responses, i.e., hardness, ultimate tensile strength and surface roughness, using the response surface methodology. The experimental results were comprehensively analyzed using statistical and scanning electron microscopic analyses. Optimized parameters were proposed and validated to achieve castings with high hardness (84.5 HB) and strength (153.5 MPa) with minimum roughness (5.8 µm).
| S-EPMC7040807 | biostudies-literature