A Refined Finite Element Formulation for the Microstructure-Dependent Analysis of Two-Dimensional (2D) Lattice Materials.
Ontology highlight
ABSTRACT:
SUBMITTER: Mancusi G
PROVIDER: S-EPMC5452127 | biostudies-other | 2012 Dec
REPOSITORIES: biostudies-other
Similar Datasets
Project description:A three dimensional viscous finite element model is presented in this paper for the analysis of the acoustic fluid structure interaction systems including, but not limited to, the cochlear-based transducers. The model consists of a three dimensional viscous acoustic fluid medium interacting with a two dimensional flat structure domain. The fluid field is governed by the linearized Navier-Stokes equation with the fluid displacements and the pressure chosen as independent variables. The mixed displacement/pressure based formulation is used in the fluid field in order to alleviate the locking in the nearly incompressible fluid. The structure is modeled as a Mindlin plate with or without residual stress. The Hinton-Huang's 9-noded Lagrangian plate element is chosen in order to be compatible with 27/4 u/p fluid elements. The results from the full 3d FEM model are in good agreement with experimental results and other FEM results including Beltman's thin film viscoacoustic element [2] and two and half dimensional inviscid elements [21]. Although it is computationally expensive, it provides a benchmark solution for other numerical models or approximations to compare to besides experiments and it is capable of modeling any irregular geometries and material properties while other numerical models may not be applicable.
| S-EPMC2824573 | biostudies-literature
Project description:Adhesive contact of a rigid flat surface with an elastic substrate having Weierstrass surface profile is numerically analyzed using the finite element method. In this work, we investigate the relationship between load and contact area spanning the limits of non-adhesive normal contact to adhesive contact for various substrate material properties, surface energy and roughness parameters. In the limit of non-adhesive normal contact, our results are consistent with published work. For the adhesive contact problem, we employ Lennard-Jones type local contact interaction model with numerical regularization to study the transition from partial to full contact including jump-to-contact instabilities as well as load-depth hysteresis. We have investigated evolution of bonded contact area and pull-off force for various surface roughness parameters, substrate material properties and surface energy. We have identified two non-dimensional parameters to adequately explain experimentally observed adhesion weakening and strengthening phenomena. A design chart of the relative pull-off force as function of non-dimensional parameters is also presented.
| S-EPMC7096536 | biostudies-literature
Project description:Isolating the role(s) of microstructural pathological features in affecting diastolic filling is important in developing targeted treatments for heart diseases. We developed a microstructure-based constitutive model of the myocardium and implemented it in an efficient open-source finite element modeling framework to simulate passive inflation of the left ventricle (LV) in a representative 3D geometry based on experimentally measured muscle fiber architecture. The constitutive model was calibrated using previous tissue-level biaxial mechanical test data derived from the canine heart and validated with independent sets of measurements made at both the isolated constituent and organ level. Using the validated model, we investigated the load taken up by each tissue constituent and their effects on LV passive inflation. The model predicts that the LV compliance is sensitive to the collagen ultrastructure, specifically, the collagen fiber azimuthal angle with respect to the local muscle fiber direction and its waviness. The model also predicts that most of the load in the sub-epicardial and sub-endocardial regions is taken up, respectively, by the muscle fibers and collagen fiber network. This result suggests that normalizing LV passive stiffness by altering the collagen fiber network and myocyte stiffness is most effective when applied to the sub-endocardial and sub-epicardial regions, respectively. This finding may have implication for the development of new pharmaceutical treatments targeting individual cardiac tissue constituents to normalize LV filling function in heart diseases. STATEMENT OF SIGNIFICANCE: Current constitutive models describing the tissue mechanical behavior of the myocardium are largely phenomenological. While able to represent the bulk tissue mechanical behavior, these models cannot distinguish the contribution of the tissue constituents and their ultrastructure to heart function. Although microstructure-based constitutive models can be used to isolate the role of tissue ultrastructure, they have not been implemented in a computational framework that can accommodate realistic 3D organ geometry. The present study addresses these issues by developing and validating a microstructure-based computational modeling framework, which is used to investigate the role of tissue constituents and their ultrastructure in affecting heart function.
| S-EPMC6677579 | biostudies-literature
Project description:A four-noded finite element of a moderately thick plate made of functionally graded material (FGM) is presented. The base element is rectangular and can be extended to any shape using a transformation based on NURBS functions. The proposed 2D shape functions are consistent with the physical interpretation and describe the states of element displacement caused by unit displacements of nodes. These functions depend on the FGM's material parameters and are called material-oriented. The shape function matrix is based on a superposition displacement field of two plate strips with 1D exact shape functions. A characteristic feature of the proposed formulation is full coupling of the membrane and bending states in the plate. The analytical form of the stiffness matrix and the nodal load vector was obtained, which leads to the numerical efficiency of the formulation. The element has been incorporated into Abaqus software with the use of Maple program. The finite element shows good convergence properties for different FGM models in the transverse direction to the middle plane of the plate. During derivation of the 2D plate element the formally exact 1D finite element for transverse nonhomogeneous FGM plate strip was developed.
| S-EPMC7040622 | biostudies-literature
Project description:IntroductionImplant material is a more important factor for periprosthetic tibial bone resorption than implant design after total knee arthroplasty (TKA). The virtual perturbation study was planned to perform using single case of proximal tibia model. We determined whether the implant materials' stiffness affects the degree of periprosthetic tibial bone resorption, and whether the effect of material change with the same implant design differed according to the proximal tibial plateau areas.Materials and methodsThis three-dimensional finite element analysis included two cobalt-chromium (CoCr) and two titanium (Ti) tibial implants with different designs. They were implanted into the proximal tibial model reconstructed using extracted images from computed tomography. The degree of bone resorption or formation was measured using the strain energy density after applying axial load. The same analysis was performed after exchanging the materials while maintaining the design of each implant.ResultsThe degree of periprosthetic tibial bone resorption was not determined by the type of implant materials alone. When the implant materials were changed from Ti to CoCr, the bone resorption in the medial compartment increased and vice versa. The effect of material composition's change on anterior and posterior areas varied accordingly.ConclusionsAlthough the degree of bone resorption was associated with implant materials, it differed depending on the design of each implant. The effect on the degree of bone resorption according to the materials after TKA should be evaluated while concomitantly considering design.
| S-EPMC7875353 | biostudies-literature
Project description:Lattice relaxation in twistronic bilayers with close lattice parameters and almost perfect crystallographic alignment of the layers results in the transformation of the moiré pattern into a sequence of preferential stacking domains and domain wall networks. Here, we show that reconstructed moiré superlattices of the perfectly aligned heterobilayers of same chalcogen transition metal dichalcogenides have broken-symmetry structures featuring twisted nodes ("twirls") of domain wall networks. The analysis of twist-angle dependence of strain characteristics for the broken-symmetry structures shows that the formation of twirl reduces the amount of hydrostatic strain around the nodes, potentially weakening their influence on the band edge energies of electrons and holes.
| S-EPMC10571146 | biostudies-literature
Project description:The lattice directly determines the electronic structure, and it enables controllably tailoring the properties by deforming the lattices of two-dimensional (2D) materials. Owing to the unbalanced electrostatic equilibrium among the dislocated atoms, the deformed lattice is thermodynamically unstable and would recover to the initial state. Here, we demonstrate that the recovery of deformed 2D lattices could be directly regulated via doping metal donors to reconstruct electrostatic equilibrium. Compared with the methods that employed external force fields with intrinsic instability and nonuniformity, the stretched 2D molybdenum diselenide (MoSe2) could be uniformly retained and permanently preserved via doping metal atoms with more outermost electrons and smaller electronegativity than Mo. We believe that the proposed strategy could open up a new avenue in directly regulating the atomic-thickness lattice and promote its practical applications based on 2D crystals.
| S-EPMC6416774 | biostudies-literature
Project description:Microstructure reconstruction serves as a crucial foundation for establishing process-structure-property (PSP) relationship in material design. Confronting the limitations of variational autoencoder and generative adversarial network within generative models, this study adopted the denoising diffusion probabilistic model (DDPM) to learn the probability distribution of high-dimensional raw data and successfully reconstructed the microstructures of various composite materials, such as inclusion materials, spinodal decomposition materials, chessboard materials, fractal noise materials, and so on. The quality of generated microstructure was evaluated using quantitative measures like spatial correlation functions and Fourier descriptor. On this basis, this study also achieved the regulation of microstructure randomness and the generation of gradient materials through continuous interpolation in latent space using denoising diffusion implicit model (DDIM). Furthermore, the two-dimensional microstructure reconstruction was extended to three-dimensional framework and integrated permeability as a feature encoding embedding. This enables the conditional generation of three-dimensional microstructures for random porous materials within a defined permeability range. The permeabilities of these generated microstructures were further validated through the application of the lattice Boltzmann method. The above methods provide new ideas and references for material reverse design.
| S-EPMC10904791 | biostudies-literature
Project description:The aim of this study was to evaluate the influence of different framework materials on biomechanical behaviour of anterior two-unit cantilever resin-bonded fixed dental prostheses (RBFDPs). A three-dimensional finite element model of a two-unit cantilever RBFDP replacing a maxillary lateral incisor was created. Five framework materials were evaluated: direct fibre-reinforced composite (FRC-Z250), indirect fibre-reinforced composite (FRC-ES), gold alloy (M), glass ceramic (GC), and zirconia (ZI). Finite element analysis was performed and stress distribution was evaluated. A similar stress pattern, with stress concentrations in the connector area, was observed in RBFDPs for all materials. Maximal principal stress showed a decreasing order: ZI>M>GC>FRC-ES>FRC-Z250. The maximum displacement of RBFDPs was higher for FRC-Z250 and FRC-ES than for M, GC, and ZI. FE analysis depicted differences in location of the maximum stress at the luting cement interface between materials. For FRC-Z250 and FRC-ES, the maximum stress was located in the upper part of the proximal area of the retainer, whereas, for M, GC, and ZI, the maximum stress was located at the cervical outline of the retainer. The present study revealed differences in biomechanical behaviour between all RBFDPs. The general observation was that a RBFDP made of FRC provided a more favourable stress distribution.
| S-EPMC4387912 | biostudies-other
Project description:Five different layered-fiber reinforced Cu-UV glue composite structures were prepared, with Cu plate and wire as the reinforcing phase, and UV glue as the substrate. The volume ratio of Cu and UV glue of these structures is the same, but the difference lies in the number and diameter of Cu wires. Three-point bending tests were performed on these structures, and the bending stress-bending strain curves of different structures were measured. At the same time, the finite element method is used to simulate the three-point bending test process of different structures, and the bending stress-bending strain curves of different structures were calculated. Then the experimental and simulated strengths corresponding to different structures were obtained from the stress-strain curves obtained by experiment and simulation. These data are supplementary material for the associated research article [1].
| S-EPMC8473658 | biostudies-literature