Hot Corrosion Behavior of Sputtered Nanocrystalline Coating with Yttrium Addition at 900 °C.
Ontology highlight
ABSTRACT:
SUBMITTER: Jiang W
PROVIDER: S-EPMC5453377 | biostudies-other | 2014 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The search for highly effective corrosion protection solutions to avoid degradation of the metallic parts is enabling the development of polymeric organic coatings. Of particular relevance, polymeric nanocomposite coatings, modified with corrosion inhibitors, have been developed to provide enhanced surface protection. In this work, yttrium oxide nanoparticles loaded with corrosion inhibitor (Imidazole), used as additives in the formulation of epoxy for coated on the steel substrate. The loading of Y2O3 with imidazole was confirmed by field emission scanning electron microscopy (FE-SEM) and Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and Brunauer-Emmett-Teller analysis. UV-Vis analysis demonstrated the pH-sensitive behavior of the imidazole that helps in self-release when necessary. Electrochemical impedance spectroscopy (EIS) of the coated samples revealed that the coating modified with Y2O3/IMD provides better corrosion protection compared to coatings containing only Y2O3. XPS analysis validated the presence of an imidazole protective film on the steel substrate that enhanced the corrosion resistance of the coated samples.
| S-EPMC8469726 | biostudies-literature
Project description:The present study explores the preparation of Al-10wt.%Zn alloy by the casting process. Nano CuO was prepared by the Co-precipitation method. The effect of adding nanostructure of (1wt.% CuO) to Al-10Zn alloy was studied the corrosion effects as-cast and with different aging temperatures (423, 443, and 463 K) for 2 h in 3.5% NaCl aqueous solution after homogenized for 2 h at 500 K at room temperature. Electrochemical measurements (OCP, Tafel, and EIS) were performed to determine the corrosion rate (C.R.) and corrosion current density (Icorr.) to find out corrosion behavior. In addition, microstructures of Al-10Zn and Al-10Zn-1CuO were observed using a scanning electron microscope, EDX mapping, and the optical microscope to investigate the effect of the nanoparticle's addition before and after aging and the corrosion test. The average crystal size and the dislocation density were calculated from the XRD pattern. The results show that the appropriate addition of CuO nanoparticles can refine the Al-10Zn alloy and shift the Al-10Zn alloy to a more noble direction.
| S-EPMC10409747 | biostudies-literature
Project description:The detonation gun sprayed Fe-Al type coatings as an alternative for austenitic valve steel, were investigated using two different methods of testing corrosion resistance. High temperature, 10-hour isothermal oxidation experiments at 550, 750, 950 and 1100 °C show differences in the oxidation behavior of Fe-Al type coatings under air atmosphere. The oxide layer ensures satisfying oxidation resistance, even at 950 and 1100 °C. Hematite, α-Al₂O₃ and metastable alumina phases were noticed on the coatings top surface, which preserves its initial thickness providing protection to the underlying substrate. In general, only negligible changes of the phase composition of the coatings were noticed with simultaneous strengthening controlled in the micro-hardness measurements, even after 10-hours of heating at 1100 °C. On the other hand, the electrochemical corrosion tests, which were carried out in 200 ppm Cl- (NaCl) and pH ~4 (H₂SO₄) solution to simulate the acid-rain environment, reveal higher values of the breakdown potential for D-gun sprayed Fe-Al type coatings than the ones for the bulk Fe-Al type alloy and Cr21Mn9Ni4 austenitic valve steel. This enables these materials to be used in structural and multifunctional applications in aggressive environments, including acidic ones.
| S-EPMC5455446 | biostudies-other
Project description:Titanium is one of the most used biomaterials for different applications. The aim of this study is to investigate the influence of adenine, thymine, and l-histidine as important biomolecules in the human body on the corrosion behavior of titanium in simulated body solutions. Open circuit measurements, potentiodynamic measurements, electrochemical impedance spectroscopy measurements, and quantum chemical calculations were employed during the investigation. All electrochemical methods used revealed that the investigated biomolecules provide better corrosion resistance to titanium in artificial body solutions. The increase in corrosion resistance is a result of the formation of a stable protective film on the metal surface. Also, quantum chemical calculations are in compliance with electrochemical test results and indicate that adenine, thymine, and l-histidine may act as corrosion inhibitors in the investigated solutions.
| S-EPMC7288364 | biostudies-literature
Project description:In order to improve the corrosion and wear resistance of biomedical Ti-6Al-4V implants, a Ta₂N nanoceramic coating was synthesized on a Ti-6Al-4V substrate by the double glow discharge plasma process. The Ta₂N coating, composed of fine nanocrystals, with an average grain size of 12.8 nm, improved the surface hardness of Ti-6Al-4V and showed good contact damage tolerance and good adhesion strength to the substrate. The corrosion resistance of the Ta₂N coating in Ringer's physiological solution at 37 °C was evaluated by different electrochemical techniques: potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), potentiostatic polarization and capacitance measurements (Mott-Schottky approach). The evolution of the surface composition of the passive films at different applied potentials was determined by X-ray photoelectron spectroscopy (XPS). The results indicated that the Ta₂N coating showed higher corrosion resistance than both commercially pure Ta and uncoated Ti-6Al-4V in this solution, because of the formed oxide film on the Ta₂N coating having a smaller carrier density (Nd) and diffusivity (Do) of point defects. The composition of the surface passive film formed on the Ta₂N coating changed with the applied potential. At low applied potentials, the oxidation of the Ta₂N coating led to the formation of tantalum oxynitride (TaOxNy) but, subsequently, the tantalum oxynitride (TaOxNy) could be chemically converted to Ta₂O₅ at higher applied potentials.
| S-EPMC5457118 | biostudies-other
Project description:Waterborne coating has recently been paid much attention. However, it cannot be used widely due to its performance limitations. Under the specified conditions of the selected resin, selecting the function pigment is key to improving the anticorrosive properties of the coating. Zinc phosphate is an environmentally protective and efficient anticorrosion pigment. In this work, zinc phosphate was used in modifying waterborne acrylic coatings. Moreover, the disbonding resistance of the coating was studied. Results showed that adding zinc phosphate can effectively inhibit the anode process of metal corrosion and enhance the wet adhesion of the coating, and consequently prevent the horizontal diffusion of the corrosive medium into the coating/metal interface and slow down the disbonding of the coating.
| S-EPMC5554035 | biostudies-other
Project description:The x-ray diffraction study of 12?nm CeO2 was carried out up to ~40?GPa using an angle dispersive synchrotron-radiation in a diamond-anvil cell with different pressure transmitting medium (PTM) (4:1 methanol: ethanol mixture, silicone oil and none) at room temperature. While the cubic fluorite-type structure CeO2 was retained to the highest pressure, there is progressive broadening and intensity reduction of the reflections with increasing pressure. At pressures above 12?GPa, an unusual change in the compression curve was detected in all experiments. Significantly, apparent negative volume compressibility was observed at P = 18-27?GPa with silicone oil as PTM, however it was not detected in other circumstances. The expansion of the unit cell volume of cubic CeO2 was about 1% at pressures of 15-27?GPa. To explain this abnormal phenomenon, a dual structure model (hard amorphous shell and relatively soft crystalline core) has been proposed.
| S-EPMC3963033 | biostudies-literature
Project description:The appearance of thin film metallic glasses (TFMGs) is gaining increasing interest because of their unique mechanical and anticorrosion properties and potential engineering applications. In this study, Cu-Zr-Al ternary thin film metallic glasses were fabricated by using DC magnetron sputtering equipment with various target powers. The evolution of the structure was systematically investigated by grazing incidence X-ray diffractometer, scanning electron microscopy, and transmission electron microscopy. The deposition rate increases with the increasing of applied target power. The as-deposited thin films show an amorphous structure. The compositional fluctuations on the nanometer scale indicate the presence of two Cu- and Zr-rich amorphous phases. The electrochemical corrosion measurements indicated that Cu-Zr-Al thin film metallic glasses had good corrosion resistance in the sulfuric acid solution. Nanoindentation results showed that the mechanical deformation was found to be homogenous and reproducible with a high value range for the hardness and modulus.
| S-EPMC6947152 | biostudies-literature
Project description:Metal corrosion is becoming increasingly serious in oil and gas production, and one way to solve this problem is to modify the metal surface. Thus, a corrosion inhibition coating on the N80 steel was constructed via the self-polymerization and assembling of the dopamine. The optimum reaction condition of polydopamine films was determined by the corrosion rate assessment of the films coated N80 steel, which was the reaction at 60 °C and 5 g/L dopamine in the Tris-HCl buffer solution (pH = 8.5) for 1 h. The spectral results confirmed the existence of the polydopamine coating on the surface of N80 steel, and high stability of the coating in the oil well produced water was observed. The anti-corrosion performance of the polydopamine-coated N80 steel confirmed that high temperature accelerated the anti-corrosion effect of the coating, and the corrosion rate of N80 plate in 90 °C oil well produced water was 0.0591 mm·a-1, lower than the standard value. The corrosion rates of the polydopamine coated N80, A3 and J55 plates at 90 °C were 0.0541 mm·a-1, 0.0498 mm·a-1 and 0.0455 mm·a-1, respectively. No significant effects of the categories of corrosive medium and steel plate on the performance of the coating were observed.
| S-EPMC8875011 | biostudies-literature
Project description:The corrosion behavior of X80 steel in the presence of coupled coating defects was simulated and studied under the interference of alternating current (AC) in an alkaline environment. The results from electrochemical measurements showed that the electrode potential of the coating defect with the smaller exposed area was lower than that with the larger area, which indicated that the steel with the smaller coating defect was more prone to corrosion. The result of weight loss tests also showed that the smaller coating defect had induced a higher corrosion rate. However, the corrosion rate of X80 steel at the larger coating defect decreased gradually with the increase of the larger defect area at a constant smaller defect area. The corrosion morphology images showed that the coating defects with smaller areas suffered from more severe pitting corrosion.
| S-EPMC5551763 | biostudies-other