Deformation and Plateau Region of Functionally Graded Aluminum Foam by Amount Combinations of Added Blowing Agent.
Ontology highlight
ABSTRACT:
SUBMITTER: Hangai Y
PROVIDER: S-EPMC5455388 | biostudies-other | 2015 Oct
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Aluminum foam is usually used as the core of composite materials by combining it with dense materials, such as in Al foam core sandwich panels and Al-foam-filled tubes, owing to its low tensile and bending strengths. In this study, all-Al foam-filled tubes consisting of ADC12 Al-Si-Cu die-cast aluminum alloy foam and a dense A1050 commercially pure Al tube with metal bonding were fabricated by friction welding. First, it was found that the ADC12 precursor was firmly bonded throughout the inner wall of the A1050 tube without a gap between the precursor and the tube by friction welding. No deformation of the tube or foaming of the precursor was observed during the friction welding. Next, it was shown that by heat treatment of an ADC12-precursor-bonded A1050 tube, gases generated by the decomposition of the blowing agent expand the softened ADC12 to produce the ADC12 foam interior of the dense A1050 tube. A holding time during the foaming process of approximately tH = 8.5 min with a holding temperature of 948 K was found to be suitable for obtaining a sound ADC12-foam-filled A1050 tube with sufficient foaming, almost uniform pore structures over the entire specimen, and no deformation or reduction in the thickness of the tube.
| S-EPMC5455387 | biostudies-other
Project description:Ceramic prostheses often fail from fracture and wear. We hypothesize that these failures may be substantially mitigated by an appropriate grading of elastic modulus at the ceramic surface. In this study, we elucidate the effect of elastic modulus profile on the flexural damage resistance of functionally graded materials (FGMs), providing theoretical guidelines for designing FGMs with superior load-bearing property. The Young's modulus of the graded structure is assumed to vary in a power-law relation with a scaling exponent n; this is in accordance with experimental observations from our laboratory and elsewhere. Based on the theory for bending of graded beams, we examine the effect of n value and bulk-to-surface modulus ratio (E(b)/E(s)) on stress distribution through the graded layer. Theory predicts that a low exponent (0.15<n<0.5), coupled with a relatively small modulus ratio (3<E(b)/E(s)<6), is most desirable for reducing the maximum stress and transferring it into the interior, while keeping the surface stress low. Experimentally, we demonstrate that elastically graded materials with various n values and E(b)/E(s) ratios can be fabricated by infiltrating alumina and zirconia with a low-modulus glass. Flexural tests show that graded alumina and zirconia with suitable values of these parameters exhibit superior load-bearing capacity, 20-50% higher than their homogeneous counterparts. Improving load-bearing capacity of ceramic materials could have broad impacts on biomedical, civil, structural, and an array of other engineering applications.
| S-EPMC3272119 | biostudies-literature
Project description:Functionally graded materials (FGMs) are compositionally gradient materials. They can achieve the controlled distribution of the desired characteristics within the same bulk material. We describe a functionally graded (FG) metal-phosphor adapting the concept of the FGM; copper (Cu) is selected as a metal and Cu- and Cl-doped ZnS (ZnS:Cu,Cl) is selected as a phosphor and FG [Cu]-[ZnS:Cu,Cl] is fabricated by a very simple powder process. The FG [Cu]-[ZnS:Cu,Cl] reveals a dual-structured functional material composed of dense Cu and porous ZnS:Cu,Cl, which is completely combined through six graded mediating layers. The photoluminescence (PL) of FG [Cu]-[ZnS:Cu,Cl] is insensitive to temperature change. FG [Cu]-[ZnS:Cu,Cl] also exhibits diode characteristics and photo reactivity for 365?nm -UV light. Our FG metal-phosphor concept can pave the way to simplified manufacturing of low-cost and can be applied to various electronic devices.
| S-EPMC4789794 | biostudies-literature
Project description:The optimal distribution of the reinforcing fibers for stiffening hollow cylindrical composites is explored using the linear elasticity theory. The spatial distribution of the vascular bundles in wild bamboo, a nature-designed functionally graded material, is the basis for the design. Our results suggest that wild bamboos maximize their flexural rigidity by optimally regulating the radial gradation of their vascular bundle distribution. This fact provides us with a plant-mimetic design principle that enables the realization of high-stiffness and lightweight cylindrical composites.
| S-EPMC5414991 | biostudies-literature
Project description:As a promising actuating material, liquid crystal elastomer (LCE) has been intensively explored in building diverse active structures and devices. Recently, direct ink writing technique has been developed to print LCE structures with various geometries and actuation behaviors. Despite the advancement in printing LCE, it remains challenging to print three-dimensional (3D) LCE structures with graded properties. Here, we report a facile method to tailor both the actuation behavior and mechanical properties of printed LCE filaments by varying printing parameters. On the basis of the comprehensive processing-structure-property relationship, we propose a simple strategy to print functionally graded LCEs, which greatly increases the design space for creating active morphing structures. We further demonstrate mitigation of stress concentration near the interface between an actuatable LCE tube and a rigid glass plate through gradient printing. The strategy developed here will facilitate potential applications of LCEs in different fields.
| S-EPMC7518867 | biostudies-literature
Project description:The ability of liquid interfaces to shape slender elastic structures provides powerful strategies to control the architecture of mechanical self assemblies. However, elastocapillarity-driven intelligent design remains unexplored in more complex architected liquids - such as foams. Here we propose a model system which combines an assembly of bubbles and a slender elastic structure. Arrangements of soap bubbles in confined environments form well-defined periodic structures, dictated by Plateau's laws. We consider a 2D foam column formed in a container with square cross-section in which we introduce an elastomer ribbon, leading to architected structures whose geometry is guided by a competition between elasticity and capillarity. In this system, we quantify both experimentally and theoretically the equilibrium shapes, using X-ray micro-tomography and energy minimisation techniques. Beyond the understanding of the amplitude of the wavy elastic ribbon deformation, we provide a detailed analysis of the profile of the ribbon, and show that such a setup can be used to grant a shape to a UV-curable composite slender structure, as a foam-forming technique suitable to miniaturisation. In more general terms, this work provides a stepping stone towards an improved understanding of the interactions between liquid foams and slender structures.
| S-EPMC9466004 | biostudies-literature
Project description:This work experimentally investigates the effect of layered structure on the static and impact response of a new layered syntactic foam developed for impact energy absorption. The layered syntactic foam had the same density of 1.6 g/cm3 and the same components of 50% large spheres (L) and 50% small spheres (S) with different structures from two layers to five layers. The impact response and energy absorption were investigated by drop-weight impact tests. Under static loading, more layers led to higher yield stress and lower energy absorption. There were three types of progressive failures of layered syntactic form under impact loading. The failure propagation was examined and found to be dependent on the layer number and impact energy. Interestingly, layered syntactic foam absorbed more energy than both of its components in terms of ductility. The ductility of layered syntactic foam decreased with the increase in layer number. The peak stress of layered syntactic foam increased with the increase in layer number. Two-layered syntactic foam LS had the highest ductility under 60 J/g impact, as well as an energy absorption of 35 J/g, compared to other layered syntactic foams. Specifically, its component L had a ductility under 70 J/g and an energy absorption of 25 J/g, while component S had a ductility under 10 J/g and an energy absorption of 10 J/g.
| S-EPMC6947444 | biostudies-literature
Project description:Aluminum matrix (Al99.5) syntactic foam containing expanded perlite particles was produced using the pressure infiltration technique. The dominant deformation mechanisms during compression of this foam were determined by sequential k-means analysis of the acoustic emission data. Since the different deformation mechanisms were concurrently active even at small strains, successive unloading and reloading measurement was proposed for cluster identification. The repetitive unloading and reloading allowed us to identify two mechanical parameters, namely the unloading modulus and the loss for unloading-reloading cycles. Based on the correlations among the strain localization within the specimen, the acoustic emission results, the changes in these mechanical parameters, and the transition from quasi-elastic deformation to plasticity were revealed in this material.
| S-EPMC6829569 | biostudies-literature
Project description:Osteochondral tissue repair remains a significant challenge in orthopedic surgery. Tissue engineering of osteochondral tissue has transpired as a potential therapeutic solution as it can effectively regenerate bone, cartilage, and the bone-cartilage interface. While advancements in scaffold fabrication and stem cell engineering have made significant progress towards the engineering of composite tissues, such as osteochondral tissue, new approaches are required to improve the outcome of such strategies. Herein, we discuss the use of a single-unit trilayer scaffold with depth-varying pore architecture and mineral environment to engineer osteochondral tissues in vivo. The trilayer scaffold includes a biomineralized bottom layer mimicking the calcium phosphate (CaP)-rich bone microenvironment, a cryogel middle layer with anisotropic pore architecture, and a hydrogel top layer. The mineralized bottom layer was designed to support bone formation, while the macroporous middle layer and hydrogel top layer were designed to support cartilage tissue formation. The bottom layer was kept acellular and the top two layers were loaded with cells prior to implantation. When implanted in vivo, these trilayer scaffolds resulted in the formation of osteochondral tissue with a lubricin-rich cartilage surface. The osteochondral tissue formation was a result of continuous differentiation of the transplanted cells to form cartilage tissue and recruitment of endogenous cells through the mineralized bottom layer to form bone tissue. Our results suggest that integrating exogenous cell-based cartilage tissue engineering along with scaffold-driven in situ bone tissue engineering could be a powerful approach to engineer analogs of osteochondral tissue. In addition to offering new therapeutic opportunities, such approaches and systems could also advance our fundamental understanding of osteochondral tissue regeneration and repair. STATEMENT OF SIGNIFICANCE:In this work, we describe the use of a single-unit trilayer scaffold with depth-varying pore architecture and mineral environment to engineer osteochondral tissues in vivo. The trilayer scaffold was designed to support continued differentiation of the donor cells to form cartilage tissue while supporting bone formation through recruitment of endogenous cells. When implanted in vivo, these trilayer scaffolds partially loaded with cells resulted in the formation of osteochondral tissue with a lubricin-rich cartilage surface. Approaches such as the one presented here that integrates ex vivo tissue engineering along with endogenous cell-mediated tissue engineering can have a significant impact in tissue engineering composite tissues with diverse cell populations and functionality.
| S-EPMC6309375 | biostudies-literature
Project description:Functionally graded soft materials (FGSMs) with microstructures and mechanical properties exhibiting gradients across a spatial volume to satisfy specific functions have received interests in recent years. How to characterize the mechanical properties of these FGSMs in vivo/in situ and/or in a non-destructive manner is a great challenge. This paper investigates the use of ultrasound elastography in the mechanical characterization of FGSMs. An efficient finite-element model was built to calculate the dispersion relation for surface waves in FGSMs. For FGSMs with large elastic gradients, the measured dispersion relation can be used to identify mechanical parameters. In the case where the elastic gradient is smaller than a certain critical value calculated here, our analysis on transient wave motion in FGSMs shows that the group velocities measured at different depths can infer the local mechanical properties. Experiments have been performed on polyvinyl alcohol (PVA) cryogel to demonstrate the usefulness of the method. Our analysis and the results may not only find broad applications in mechanical characterization of FGSMs but also facilitate the use of shear wave elastography in clinics because many diseases change the local elastic properties of soft tissues and lead to different material gradients. This article is part of the theme issue 'Rivlin's legacy in continuum mechanics and applied mathematics'.
| S-EPMC6452040 | biostudies-literature