Upgrade Recycling of Cast Iron Scrap Chips towards β-FeSi₂ Thermoelectric Materials.
Ontology highlight
ABSTRACT:
SUBMITTER: Laila A
PROVIDER: S-EPMC5456158 | biostudies-other | 2014 Sep
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Thermoelectric modules, consisting of multiple pairs of n- and p-type legs, enable converting heat into electricity and vice versa. However, the thermoelectric performance is often asymmetrical, in that one type outperforms the other. In this paper, we identified the relationship between the asymmetrical thermoelectric performance and the weighted mobility ratio, a correlation that can help predict the thermoelectric performance of unreported materials. Here, a reasonably high ZT for the n-type ZrCoBi-based half-Heuslers is first predicted and then experimentally verified. A high peak ZT of ~1 at 973 K can be realized by ZrCo0.9Ni0.1Bi0.85Sb0.15. The measured heat-to-electricity conversion efficiency for the unicouple of ZrCoBi-based materials can be as high as ~10% at the cold-side temperature of ~303 K and at the hot-side temperature of ~983 K. Our work demonstrates that the ZrCoBi-based half-Heuslers are highly promising for the application of mid- and high-temperature thermoelectric power generation.
| S-EPMC6588382 | biostudies-literature
Project description:Liquid-like materials are one family of promising thermoelectric materials discovered in the past years due to their advantanges of ultrahigh thermoelectric figure of merit (zT), low cost, and environmental friendliness. However, their practial applications are greatly limited by the low service stability from the Cu/Ag metal deposition under large current and/or temperature gradient. Both high zT for high efficiency and large critical voltage for good stability are required for liquid-like materials, but they are usually strongly correlated and hard to be tuned individually. Herein, based on the thermodynamic analysis, it is shown that such a correlation can be decoupled through doping immobile ions into the liquid-like sublattice. Taking Cu2- δ S as an example, doping immobile Fe ions in Cu1.90S scarcely degrades the initial large critical voltage, but significantly enhances the zT to 1.5 at 1000 K by tuning the carrier concentration to the optimal range. Combining the low-cost and environmentally friendly features, these Fe-doped Cu2- δ S-based compounds show great potential in civil applications. This study sheds light on the realization of both good stability and high performance for many other liquid-like thermoelectric materials that have not been considered for real applications before.
| S-EPMC6947709 | biostudies-literature
Project description:The best thermoelectric materials are believed to be heavily doped semiconductors. The presence of a band gap is assumed to be essential to achieve large thermoelectric power factor and figure of merit. In this work, we propose semi-metals with large asymmetry between conduction and valence bands as an alternative class of thermoelectric materials. To illustrate the idea, we study semi-metallic HgTe in details experimentally and theoretically. We employ ab initio calculations with hybrid exchange-correlation functional to accurately describe the electronic band structure in conjunction with the Boltzmann Transport theory to investigate the electronic transport properties. We calculate the lattice thermal conductivity using first principles calculations and evaluate the overall figure of merit. To validate our theoretical approach, we prepare semi-metallic HgTe samples and characterize their transport properties. Our first-principles calculations agree well with the experimental data. We show that intrinsic HgTe, a semimetal with large disparity in its electron and hole masses, has a high thermoelectric power factor that is comparable to the best known thermoelectric materials. Finally, we propose other possible materials with similar band structures as potential candidates for thermoelectric applications.
| S-EPMC6026171 | biostudies-literature
Project description:Microbial growth is an exothermic process. Biotechnological industries produce large amounts of heat, usually considered an undesirable by-product. In this work, we report the construction and characterization of the first microbial thermoelectric cell (MTC), in which the metabolic heat produced by a thermally insulated microbial culture is partially converted into electricity through a thermoelectric device optimized for low ?T values. A temperature of 41°C and net electric voltage of around 250-600 mV was achieved with 1.7 L baker's yeast culture. This is the first time microbial metabolic energy has been converted into electricity with an ad hoc thermoelectric device. These results might contribute towards developing a novel strategy to harvest excess heat in the biotechnology industry, in processes such as ethanol fermentation, auto thermal aerobic digestion (ATAD) or bioremediation, which could be coupled with MTCs in a single unit to produce electricity as a valuable by-product of the primary biotechnological product. Additionally, we propose that small portable MTCs could be conceived and inoculated with suitable thermophilic of hyperthermophilic starter cultures and used for powering small electric devices.
| S-EPMC3582603 | biostudies-literature
Project description:Thermoelectric technology offers the opportunity of direct conversion between heat and electricity, and new and exciting materials that can enable this technology to deliver higher efficiencies have been developed in recent years. This mini-review covers the most promising advances in thermoelectric materials as they pertain to their potential in being implemented in devices and modules with an emphasis on thermoelectric power generation. Classified into three groups in terms of their operating temperature, the thermoelectric materials that are most likely to be used in future devices are briefly discussed. We summarize the state-of-the-art thermoelectric modules/devices, among which nanostructured PbTe modules are particularly highlighted. At the end, key issues and the possible strategies that can help thermoelectric power generation technology move forward are considered. This article is part of a discussion meeting issue 'Energy materials for a low carbon future'.
| S-EPMC6635637 | biostudies-literature
Project description:The review embraces a number of research papers concerning the fabrication of oxide thermoelectric systems, with TiO2-SrTiO3 biphase ceramics being emphasized. The ceramics is particularly known for a two-dimensional electron gas (2DEG) forming spontaneously on the TiO2/SrTiO3 heterointerface (modulation doping), unlike ordinary 2DEG occurrence on specially fabricated thin film. Such effect is provided by the SrTiO3 conduction band edge being 0.40 and 0.20 eV higher than that for anatase and rutile TiO2, respectively. That is why, in the case of a checkered arrangement of TiO2 and SrTiO3 grains, the united 2D net is probably formed along the grain boundaries with 2DEG occurring there. To reach such conditions, there should be applied novelties in the field of ceramics materials science, because it is important to obtain highly dense material preserving small (nanoscale) grain size and thin interface boundary. The review also discusses some aspects of reactive spark plasma sintering as a promising method of preparing perovskite-oxide TiO2-SrTiO3 thermoelectric materials for high-temperature applications.
| S-EPMC6766282 | biostudies-literature
Project description:Simultaneously optimizing electrical and thermal transport properties of bulk thermoelectric materials remains a key challenge due to the conflicting combination of material traits. Here, we have explored the electrical and thermal transport features of In-filled CoSb3 through X-ray absorption fine structure, X-ray photoemission spectra, transport measurement and theoretical calculation. The results provide evidence of three types of coexisting multi-localization transport behaviours in the material; these are heat-carrying phonon-localized resonant scattering, accelerated electron movement and increase in density of states near the Fermi level. The 5p-orbital hybridization between In and Sb is discovered in the In-filled CoSb3 compound, which results in a charge transfer from Sb to In and the enhancement of p-d orbital hybridization between Co and Sb. Our work demonstrates that the electrical and thermal properties of filled skutterudite bulk thermoelectric materials can be simultaneously optimized through the three types of coexisting multi-localization transport behaviours in an independent way.
| S-EPMC4327545 | biostudies-literature
Project description:Thermoelectric technology, which possesses potential application in recycling industrial waste heat as energy, calls for novel high-performance materials. The systematic exploration of novel thermoelectric materials with excellent electronic transport properties is severely hindered by limited insight into the underlying bonding orbitals of atomic structures. Here we propose a simple yet successful strategy to discover and design high-performance layered thermoelectric materials through minimizing the crystal field splitting energy of orbitals to realize high orbital degeneracy. The approach naturally leads to design maps for optimizing the thermoelectric power factor through forming solid solutions and biaxial strain. Using this approach, we predict a series of potential thermoelectric candidates from layered CaAl2Si2-type Zintl compounds. Several of them contain nontoxic, low-cost and earth-abundant elements. Moreover, the approach can be extended to several other non-cubic materials, thereby substantially accelerating the screening and design of new thermoelectric materials.
| S-EPMC4786678 | biostudies-literature
Project description:Thermoelectric coolers are attracting significant attention for replacing age-old cooling and refrigeration devices. Localized cooling by wearable thermoelectric coolers will decrease the usage of traditional systems, thereby reducing global warming and providing savings on energy costs. Since human skin as well as ambient air is a poor conductor of heat, wearable thermoelectric coolers operate under huge thermally resistive environment. The external thermal resistances greatly influence thermoelectric material behavior, device design, and device performance, which presents a fundamental challenge in achieving high efficiency for on-body applications. Here, we examine the combined effect of heat source/sink thermal resistances and thermoelectric material properties on thermoelectric cooler performance. Efficient thermoelectric coolers demonstrated here can cool the human skin up to 8.2 °C below the ambient temperature (170% higher cooling than commercial modules). Cost-benefit analysis shows that cooling over material volume for our optimized thermoelectric cooler is 500% higher than that of the commercial modules.
| S-EPMC6468009 | biostudies-literature
Project description:Thermal interface materials (TIMs) are extensively used in electronic devices as efficient heat transfer materials. We fabricated all-carbon TIMs by hybridizing single-wall carbon nanotubes (SWCNTs) with graphite and demonstrated their performance by applying them to a thermoelectric generator (TEG) device. The hybrid carbon TIM exhibited maximum thermal conductivity when the SWCNT content was near 10 wt%. The TIM thermal contact resistance measured by a home-made calorimeter setup was 2.19 × 10-4 m2K/W, which did not vary with temperature but decreased with applied pressure. Post-treatment of the TIM with a silane coupling agent further reduced the TIM thermal contact resistance by 30%. When the TIM was placed between a TEG device and a copper heat reservoir, the TEG output power increased with the temperature difference across the TEG and applied pressure. Moreover, the post-treatment of the TIM enhanced the output power of the TEG device by up to 18.5%. This work provides a simple and effective pathway towards a carbon-based TIM that can be applied to a high temperature TEG.
| S-EPMC7606529 | biostudies-literature